Site Authoring and Deployment Guide =================================== The document contains the instructions for standing up a greenfield Airship site. This can be broken down into two high-level pieces: 1. **Site authoring guide(s)**: Describes how to craft site manifests and configs required to perform a deployment. The primary site authoring guide is for deploying Airship sites, where OpenStack is the target platform deployed on top of Airship. 2. **Deployment guide(s)**: Describes how to apply site manifests for a given site. This document is an "all in one" site authoring guide + deployment guide for a standard Airship deployment. For the most part, the site authoring guidance lives within ``airship-seaworthy`` reference site in the form of YAML comments. Terminology ----------- **Cloud**: A platform that provides a standard set of interfaces for `IaaS `__ consumers. **OSH**: (`OpenStack Helm `__) is a collection of Helm charts used to deploy OpenStack on kubernetes. **Undercloud/Overcloud**: Terms used to distinguish which cloud is deployed on top of the other. In Airship sites, OpenStack (overcloud) is deployed on top of Kubernetes (undercloud). **Airship**: A specific implementation of OpenStack Helm charts onto kubernetes, the deployment of which is the primary focus of this document. **Control Plane**: From the point of view of the cloud service provider, the control plane refers to the set of resources (hardware, network, storage, etc) sourced to run cloud services. **Data Plane**: From the point of view of the cloud service provider, the data plane is the set of resources (hardware, network, storage, etc.) sourced to run consumer workloads. When used in this document, "data plane" refers to the data plane of the overcloud (OSH). **Host Profile**: A host profile is a standard way of configuring a bare metal host. Encompasses items such as the number of bonds, bond slaves, physical storage mapping and partitioning, and kernel parameters. Component Overview ~~~~~~~~~~~~~~~~~~ .. image:: diagrams/component_list.png Node Overview ~~~~~~~~~~~~~ This document refers to several types of nodes, which vary in their purpose, and to some degree in their orchestration / setup: - **Build node**: This refers to the environment where configuration documents are built for your environment (e.g., your laptop) - **Genesis node**: The "genesis" or "seed node" refers to a node used to get a new deployment off the ground, and is the first node built in a new deployment environment. - **Control / Controller nodes**: The nodes that make up the control plane. (Note that the Genesis node will be one of the controller nodes.) - **Compute nodes / Worker Nodes**: The nodes that make up the data plane Support ------- Bugs may be viewed and reported at the following locations, depending on the component: - OpenStack Helm: `OpenStack Storyboard group `__ - Airship: Bugs may be filed using OpenStack Storyboard for specific projects in `Airship group `__: - `Airship Armada `__ - `Airship Berth `__ - `Airship Deckhand `__ - `Airship Divingbell `__ - `Airship Drydock `__ - `Airship MaaS `__ - `Airship Pegleg `__ - `Airship Promenade `__ - `Airship Shipyard `__ - `Airship in a Bottle `__ - `Airship Treasuremap `__ Hardware Prep ------------- Disk ~~~~ 1. For servers that are in the control plane (including Genesis): - Two-disk RAID-1: Operating System - Two disks JBOD: Ceph Journal/Meta - Remaining disks JBOD: Ceph OSD 2. For servers that are in the tenant data plane (compute nodes): - Two-disk RAID-1: Operating System - Two disks JBOD: Ceph Journal/Meta - Two disks JBOD: Ceph OSD - Remaining disks need to be configured according to the host profile target for each given server (e.g. RAID-10 for OpenStack Ephemeral). BIOS and IPMI ~~~~~~~~~~~~~ 1. Virtualization enabled in BIOS 2. IPMI enabled in server BIOS (e.g., IPMI over LAN option enabled) 3. IPMI IPs assigned, and routed to the environment you will deploy into Note: Firmware bugs related to IPMI are common. Ensure you are running the latest firmware version for your hardware. Otherwise, it is recommended to perform an iLo/iDrac reset, as IPMI bugs with long-running firmware are not uncommon. 4. Set PXE as first boot device and ensure the correct NIC is selected for PXE Network ~~~~~~~ 1. You have a network you can successfully PXE boot with your network topology and bonding settings (dedicated PXE interace on untagged/native VLAN in this example) 2. You have (VLAN) segmented, routed networks accessible by all nodes for: 1. Management network(s) (k8s control channel) 2. Calico network(s) 3. Storage network(s) 4. Overlay network(s) 5. Public network(s) HW Sizing and minimum requirements ---------------------------------- +----------+----------+----------+----------+ | Node | disk | memory | cpu | +==========+==========+==========+==========+ | Build | 10 GB | 4 GB | 1 | +----------+----------+----------+----------+ | Genesis | 100 GB | 16 GB | 8 | +----------+----------+----------+----------+ | Control | 10 TB | 128 GB | 24 | +----------+----------+----------+----------+ | Compute | N/A* | N/A* | N/A* | +----------+----------+----------+----------+ * Workload driven (determined by host profile) Establishing build node environment ----------------------------------- 1. On the machine you wish to use to generate deployment files, install required tooling:: sudo apt -y install docker.io git 2. Clone and link the required git repos as follows:: git clone https://git.openstack.org/openstack/airship-pegleg git clone https://git.openstack.org/openstack/airship-treasuremap Building Site documents ----------------------- This section goes over how to put together site documents according to your specific environment, and generate the initial Promenade bundle needed to start the site deployment. Preparing deployment documents ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ In its current form, pegleg provides an organized structure for YAML elements, in order to separate common site elements (i.e., ``global`` folder) from unique site elements (i.e., ``site`` folder). To gain a full understanding of the pegleg structure, it is highly recommended to read pegleg documentation on this `here `__. The ``airship-seaworthy`` site may be used as reference site. It is the principal pipeline for integration and continuous deployment testing of Airship. Change directory to the ``airship-treasuremap/site`` folder and copy the ``airship-seaworthy`` site as follows: :: NEW_SITE=mySite # replace with the name of your site cd airship-treasuremap/site cp -r airship-seaworthy $NEW_SITE Remove ``airship-seaworthy`` specific certificates. :: rm -f airship-treasuremap/site/${NEW_SITE}/secrets/certificates/certificates.yaml You will then need to manually make changes to these files. These site manifests are heavily commented to explain parameters, and importantly identify all of the parameters that need to change when authoring a new site. These areas which must be updated for a new site are flagged with the label ``NEWSITE-CHANGEME`` in YAML commentary. Search for all instances of ``NEWSITE-CHANGEME`` in your new site definition, and follow the instructions that accompany the tag in order to make all needed changes to author your new Airship site. Because some files depend on (or will repeat) information from others, the order in which you should build your site files is as follows: 1. site/$NEW\_SITE/networks/physical/networks.yaml 2. site/$NEW\_SITE/baremetal/nodes.yaml 3. site/$NEW\_SITE/networks/common-addresses.yaml 4. site/$NEW\_SITE/pki/pki-catalog.yaml 5. All other site files Register DNS names ~~~~~~~~~~~~~~~~~~ Register the following list of DNS names: :: cloudformation.DOMAIN compute.DOMAIN dashboard.DOMAIN grafana.DOMAIN iam.DOMAIN identity.DOMAIN image.DOMAIN kibana.DOMAIN nagios.DOMAIN network.DOMAIN nova-novncproxy.DOMAIN object-store.DOMAIN orchestration.DOMAIN placement.DOMAIN shipyard.DOMAIN volume.DOMAIN Here ``DOMAIN`` is a name of ingress domain, you can find it in the ``data.dns.ingress_domain`` section of ``site/${NEW_SITE}/secrets/certificates/ingress.yaml`` configuration file. Run the following command to get up to date list of required DNS names: :: grep -E 'host: .+DOMAIN' site/${NEW_SITE}/software/config/endpoints.yaml | \ sort -u | awk '{print $2}' Update Secrets ~~~~~~~~~~~~~~ Replace passphrases under ``site/${NEW_SITE}/secrets/passphrases/`` with random generated ones: - Passpharses generation ``openssl rand -hex 10`` - UUID generation ``uuidgen`` (e.g. for Ceph filesystem ID) - Update ``secrets/passphrases/ipmi_admin_password.yaml`` with IPMI password - Update ``secrets/passphrases/ubuntu_crypt_password.yaml`` with password hash: :: python3 -c "from crypt import *; print(crypt('', METHOD_SHA512))" Configure certificates in ``site/${NEW_SITE}/secrets/certificates/ingress.yaml``, they need to be issued for the domains configured in ``Register DNS names`` section. .. caution:: It is required to configure valid certificates, self-signed certificates are not supported. Control Plane Ceph Cluster Notes ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Configuration variables for ceph control plane are located in: - ``site/${NEW_SITE}/software/charts/ucp/ceph/ceph-osd.yaml`` - ``site/${NEW_SITE}/software/charts/ucp/ceph/ceph-client.yaml`` Setting highlights: - data/values/conf/storage/osd[\*]/data/location: The block device that will be formatted by the Ceph chart and used as a Ceph OSD disk - data/values/conf/storage/osd[\*]/journal/location: The block device backing the ceph journal used by this OSD. Refer to the journal paradigm below. - data/values/conf/pool/target/osd: Number of OSD disks on each node Assumptions: 1. Ceph OSD disks are not configured for any type of RAID, they are configured as JBOD when connected through a RAID controller. If RAID controller does not support JBOD, put each disk in its own RAID-0 and enable RAID cache and write-back cache if the RAID controller supports it. 2. Ceph disk mapping, disk layout, journal and OSD setup is the same across Ceph nodes, with only their role differing. Out of the 4 control plane nodes, we expect to have 3 actively participating in the Ceph quorom, and the remaining 1 node designated as a standby Ceph node which uses a different control plane profile (cp\_*-secondary) than the other three (cp\_*-primary). 3. If doing a fresh install, disk are unlabeled or not labeled from a previous Ceph install, so that Ceph chart will not fail disk initialization. It's highly recommended to use SSD devices for Ceph Journal partitions. If you have an operating system available on the target hardware, you can determine HDD and SSD devices with: :: lsblk -d -o name,rota where a ``rota`` (rotational) value of ``1`` indicates a spinning HDD, and where a value of ``0`` indicates non-spinning disk (i.e. SSD). (Note - Some SSDs still report a value of ``1``, so it is best to go by your server specifications). For OSDs, pass in the whole block device (e.g., ``/dev/sdd``), and the Ceph chart will take care of disk partitioning, formatting, mounting, etc. For Ceph Journals, you can pass in a specific partition (e.g., ``/dev/sdb1``), note that it's not required to pre-create these partitions, Ceph chart will create journal partitions automatically if they don't exist. By default the size of every journal partition is 10G, make sure there is enough space available to allocate all journal partitions. Consider the following example where: - /dev/sda is an operating system RAID-1 device (SSDs for OS root) - /dev/sd[bc] are SSDs for ceph journals - /dev/sd[efgh] are HDDs for OSDs The data section of this file would look like: :: data: values: conf: storage: osd: - data: type: block-logical location: /dev/sde journal: type: block-logical location: /dev/sdb1 - data: type: block-logical location: /dev/sdf journal: type: block-logical location: /dev/sdb2 - data: type: block-logical location: /dev/sdg journal: type: block-logical location: /dev/sdc1 - data: type: block-logical location: /dev/sdh journal: type: block-logical location: /dev/sdc2 Manifest linting and combining layers ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ After constituent YAML configurations are finalized, use Pegleg to lint your manifests, and resolve any issues that result from linting before proceeding: :: sudo airship-pegleg/tools/pegleg.sh repo \ -r airship-treasuremap lint Note: ``P001`` and ``P003`` linting errors are expected for missing certificates, as they are not generated until the next section. You may suppress these warnings by appending ``-x P001 -x P003`` to the lint command. Next, use pegleg to perform the merge that will yield the combined global + site type + site YAML: :: sudo sh airship-pegleg/tools/pegleg.sh site \ -r airship-treasuremap \ collect $NEW_SITE Perform a visual inspection of the output. If any errors are discovered, you may fix your manifests and re-run the ``lint`` and ``collect`` commands. After you have an error-free output, save the resulting YAML as follows: :: sudo airship-pegleg/tools/pegleg.sh site \ -r airship-treasuremap \ collect $NEW_SITE -s ${NEW_SITE}_collected It is this output which will be used in subsequent steps. Lastly, you should also perform a ``render`` on the documents. The resulting render from Pegleg will not be used as input in subsequent steps, but is useful for understanding what the document will look like once Deckhand has performed all substitutions, replacements, etc. This is also useful for troubleshooting, and addressing any Deckhand errors prior to submitting via Shipyard: :: sudo airship-pegleg/tools/pegleg.sh site \ -r airship-treasuremap \ render $NEW_SITE Inspect the rendered document for any errors. If there are errors, address them in your manifests and re-run this section of the document. Building the Promenade bundle ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Clone the Promenade repo, if not already cloned: :: git clone https://github.com/openstack/airship-promenade Refer to the ``data/charts/ucp/promenade/reference`` field in ``airship-treasuremap/global/software/config/versions.yaml``. If this is a pinned reference (i.e., any reference that's not ``master``), then you should checkout the same version of the Promenade repository. For example, if the Promenade reference was ``86c3c11...`` in the versions file, checkout the same version of the Promenade repo which was cloned previously: :: (cd airship-promenade && git checkout 86c3c11) Likewise, before running the ``simple-deployment.sh`` script, you should refer to the ``data/images/ucp/promenade/promenade`` field in ``~/airship-treasuremap/global/software/config/versions.yaml``. If there is a pinned reference (i.e., any image reference that's not ``latest``), then this reference should be used to set the ``IMAGE_PROMENADE`` environment variable. For example, if the Promenade image was pinned to ``quay.io/airshipit/promenade:d30397f...`` in the versions file, then export the previously mentioned environment variable like so: :: export IMAGE_PROMENADE=quay.io/airshipit/promenade:d30397f... Now, create an output directory for Promenade bundles and run the ``simple-deployment.sh`` script: :: mkdir ${NEW_SITE}_bundle sudo -E airship-promenade/tools/simple-deployment.sh ${NEW_SITE}_collected ${NEW_SITE}_bundle Estimated runtime: About **1 minute** After the bundle has been successfully created, copy the generated certificates into the security folder. Ex: :: mkdir -p airship-treasuremap/site/${NEW_SITE}/secrets/certificates sudo cp ${NEW_SITE}_bundle/certificates.yaml \ airship-treasuremap/site/${NEW_SITE}/secrets/certificates/certificates.yaml Regenerate collected YAML files to include copied certificates: :: sudo airship-pegleg/tools/pegleg.sh site \ -r airship-treasuremap \ collect $NEW_SITE -s ${NEW_SITE}_collected Genesis node ------------ Initial setup ~~~~~~~~~~~~~ Before starting, ensure that the BIOS and IPMI settings match those stated previously in this document. Also ensure that the hardware RAID is setup for this node per the control plane disk configuration stated previously in this document. Then, start with a manual install of Ubuntu 16.04 on the node you wish to use to seed the rest of your environment standard `Ubuntu ISO `__. Ensure to select the following: - UTC timezone - Hostname that matches the Genesis hostname given in ``/data/genesis/hostname`` in ``airship-treasuremap/site/${NEW_SITE}/networks/common-addresses.yaml``. - At the ``Partition Disks`` screen, select ``Manual`` so that you can setup the same disk partitioning scheme used on the other control plane nodes that will be deployed by MaaS. Select the first logical device that corresponds to one of the RAID-1 arrays already setup in the hardware controller. On this device, setup partitions matching those defined for the ``bootdisk`` in your control plane host profile found in ``airship-treasuremap/site/${NEW_SITE}/profiles/host``. (e.g., 30G for /, 1G for /boot, 100G for /var/log, and all remaining storage for /var). Note that the volume size syntax looking like ``>300g`` in Drydock means that all remaining disk space is allocated to this volume, and that volume needs to be at least 300G in size. - Ensure that OpenSSH and Docker (Docker is needed because of miniMirror) are included as installed packages - When you get to the prompt, "How do you want to manage upgrades on this system?", choose "No automatic updates" so that packages are only updated at the time of our choosing (e.g. maintenance windows). - Ensure the grub bootloader is also installed to the same logical device as in the previous step (this should be default behavior). After installation, ensure the host has outbound internet access and can resolve public DNS entries (e.g., ``nslookup google.com``, ``curl https://www.google.com``). Ensure that the deployed Genesis hostname matches the hostname in ``data/genesis/hostname`` in ``airship-treasuremap/site/${NEW_SITE}/networks/common-addresses.yaml``. If it does not match, then either change the hostname of the node to match the configuration documents, or re-generate the configuration with the correct hostname. In order to change the hostname of the deployed node, you may run the following: :: sudo hostname $NEW_HOSTNAME sudo sh -c "echo $NEW_HOSTNAME > /etc/hostname" sudo vi /etc/hosts # Anywhere the old hostname appears in the file, replace # with the new hostname Or to regenerate manifests, re-run the previous two sections with the after updating the genesis hostname in the site definition. Installing matching kernel version ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Install the same kernel version on the Genesis host that MaaS will use to deploy new baremetal nodes. In order to do this, first you must determine the kernel version that will be deployed to those nodes. Start by looking at the host profile definition used to deploy other control plane nodes by searching for ``control-plane: enabled``. Most likely this will be a file under ``global/profiles/host``. In this file, find the kernel info - e.g.: :: platform: image: 'xenial' kernel: 'hwe-16.04' kernel_params: kernel_package: 'linux-image-4.15.0-34-generic' In this example, the kernel version is ``4.15.0-34-generic``. Define any proxy environment variables needed for your environment to reach public ubuntu package repos, and install the matching kernel on the Genesis host (make sure to run on Genesis host, not on the build host): :: sudo apt -y install linux-modules-4.15.0-34-generic \ linux-modules-extra-4.15.0-34-generic \ linux-image-4.15.0-34-generic linux-headers-4.15.0-34-generic \ linux-headers-4.15.0-34 Check the installed packages on the genesis host with ``dpkg --list``. If there are any later kernel versions installed, remove them with ``sudo apt remove``, so that the newly install kernel is the latest available. Install ntpdate/ntp ~~~~~~~~~~~~~~~~~~~ Install and run ntpdate, to ensure a reasonably sane time on genesis host before proceeding: :: sudo apt -y install ntpdate sudo ntpdate ntp.ubuntu.com If your network policy does not allow time sync with external time sources, specify a local NTP server instead of using ``ntp.ubuntu.com``. Then, install the NTP client: :: sudo apt -y install ntp Add the list of NTP servers specified in ``data/ntp/servers_joined`` in file ``airship-treasuremap/site/${NEW_SITE}/networks/common-address.yaml`` to ``/etc/ntp.conf`` as follows: :: pool NTP_SERVER1 iburst pool NTP_SERVER2 iburst (repeat for each NTP server with correct NTP IP or FQDN) Then, restart the NTP service: :: sudo service ntp restart If you cannot get good time to your selected time servers, consider using alternate time sources for your deployment. Disable the apparmor profile for ntpd: :: sudo ln -s /etc/apparmor.d/usr.sbin.ntpd /etc/apparmor.d/disable/ sudo apparmor_parser -R /etc/apparmor.d/usr.sbin.ntpd This prevents an issue with the MaaS containers, which otherwise get permission denied errors from apparmor when the MaaS container tries to leverage libc6 for /bin/sh when MaaS container ntpd is forcefully disabled. Promenade bootstrap ~~~~~~~~~~~~~~~~~~~ Copy the ``${NEW_SITE}_bundle`` and ``${NEW_SITE}_collected`` directories from the build node to the genesis node, into the home directory of the user there (e.g., ``/home/ubuntu``). Then, run the following script as sudo on the genesis node: :: cd ${NEW_SITE}_bundle sudo ./genesis.sh Estimated runtime: **40m** Following completion, run the ``validate-genesis.sh`` script to ensure correct provisioning of the genesis node: :: cd ${NEW_SITE}_bundle sudo ./validate-genesis.sh Estimated runtime: **2m** Deploy Site with Shipyard ------------------------- Start by cloning the shipyard repository to the Genesis node: :: git clone https://github.com/openstack/airship-shipyard Refer to the ``data/charts/ucp/shipyard/reference`` field in ``airship-treasuremap/global/software/config/versions.yaml``. If this is a pinned reference (i.e., any reference that's not ``master``), then you should checkout the same version of the Shipyard repository. For example, if the Shipyard reference was ``7046ad3...`` in the versions file, checkout the same version of the Shipyard repo which was cloned previously: :: (cd airship-shipyard && git checkout 7046ad3) Likewise, before running the ``deckhand_load_yaml.sh`` script, you should refer to the ``data/images/ucp/shipyard/shipyard`` field in ``airship-treasuremap/global/software/config/versions.yaml``. If there is a pinned reference (i.e., any image reference that's not ``latest``), then this reference should be used to set the ``SHIPYARD_IMAGE`` environment variable. For example, if the Shipyard image was pinned to ``quay.io/airshipit/shipyard@sha256:dfc25e1...`` in the versions file, then export the previously mentioned environment variable: :: export SHIPYARD_IMAGE=quay.io/airshipit/shipyard@sha256:dfc25e1... Export valid login credentials for one of the Airship Keystone users defined for the site. Currently there is no authorization checks in place, so the credentials for any of the site-defined users will work. For example, we can use the ``shipyard`` user, with the password that was defined in ``airship-treasuremap/site/${NEW_SITE}/secrets/passphrases/ucp_shipyard_keystone_password.yaml``. Ex: :: export OS_USERNAME=shipyard export OS_PASSWORD=46a75e4... (Note: Default auth variables are defined `here `__, and should otherwise be correct, barring any customizations of these site parameters). Next, run the deckhand\_load\_yaml.sh script providing an absolute path to a directory that contains collected manifests: :: sudo -E airship-shipyard/tools/deckhand_load_yaml.sh ${NEW_SITE} $(pwd)/${NEW_SITE}_collected Estimated runtime: **3m** Now deploy the site with shipyard: :: cd airship-shipyard/tools/ sudo -E ./deploy_site.sh Estimated runtime: **1h30m** The message ``Site Successfully Deployed`` is the expected output at the end of a successful deployment. In this example, this means that Airship and OSH should be fully deployed. Disable password-based login on Genesis --------------------------------------- Before proceeding, verify that your SSH access to the Genesis node is working with your SSH key (i.e., not using password-based authentication). Then, disable password-based SSH authentication on Genesis in ``/etc/ssh/sshd_config`` by uncommenting the ``PasswordAuthentication`` and setting its value to ``no``. Ex: :: PasswordAuthentication no Then, restart the ssh service: :: sudo systemctl restart ssh