treasuremap/doc/source/troubleshooting_guide.rst

Troubleshooting Guide

This guide provides information on troubleshooting of an Airship environment. Debugging of any software component starts with gathering more information about the failure, so the intention of the document is not to describe specific issues that one can encounter, but to provide a generic set of instructions that a user can follow to find the root cause of the problem.

For additional support you can contact the Airship team via IRC or mailing list, use Airship bug tracker <https://storyboard.openstack.org/#!/ project_group/Airship>__ to search and create issues.

Table of Contents

Additional Troubleshooting

troubleshooting_ceph.rst

Perform Health Checks

The first step in troubleshooting an Airship deployment is to identify unhealthy services by performing health checks.

Verify Peering is established

sudo /opt/cni/bin/calicoctl node status

Calico process is running.
IPv4 BGP status
+--------------+-----------+-------+------------+-------------+
| PEER ADDRESS | PEER TYPE | STATE | SINCE | INFO |
+--------------+-----------+-------+------------+-------------+
| 172.29.0.2 | global | up | 2018-05-22 | Established |
| 172.29.0.3 | global | up | 2018-05-22 | Established |
+--------------+-----------+-------+------------+-------------+
IPv6 BGP status No IPv6 peers found.

Verify that STATE is up and INFO is Established. However, if STATE is start and INFO is Connect, peering has failed.

For more information on Calico troubleshooting, visit the Calico Documentation

Verify the Health of Kubernetes

# Verify that for all nodes, STATE is Ready.
#
# Note: After a reboot, it may take as long as 30 minutes for
# a node to stabilize and reach a Ready condition.
kubectl get nodes

# Verify that liveness probes for all pods are working.
# This command exposes pods whose liveness probe is failing.
kubectl get pods --all-namespaces | grep Running | grep 0/

# Verify that all pods are in the Running or Completed state.
# This command exposes pods that are not running or completed.
kubectl get pods --all-namespaces | grep -v Running | Completed

# Look for crashed pods.
kubectl get pods --all-namespaces -o wide | grep Crash

# Check the health of core services.
kubectl get pods --all-namespaces -o wide | grep core
kubectl get services --all-namespaces | grep core

# Check the health of proxy services.
kubectl get pods --all-namespaces -o wide | grep proxy

# Get all pod details.
kubectl get pods --all-namespaces -o wide -w

# Look for failed jobs.
kubectl get jobs – --all-namespaces -o wide | grep -v "1    1"

Verify the Health of OpenStack

Check OpenStack's health by issuing the following commands at the terminal, in order to do so you must have a set an OpenStack RC file, details here <https://docs.openstack.org/mitaka/cli-reference/common/cli_set_ environment_variables_using_openstack_rc.html#download-and-source-the- openstack-rc-file>__

# Verify Keystone by requesting a token.
openstack token issue

# Verify networks.
openstack network list

# Verify subnets.
openstack subnet list

# Verify VMs.
openstack server list

# Verify compute hypervisors.
openstack hypervisor list

# Verify Images
openstack image list

Check for kube-proxy iptables NAT Issues

# Check the iptables and make sure the IP addresses are the same:
% iptables -n -t nat -L | grep coredns
% kubectl -n kube-system get -o wide pod | grep coredns

Configuring Airship CLI

Many commands from this guide use Airship CLI, this section describes how to get it configured on your environment.

git clone https://opendev.org/airship/treasuremap
cd treasuremap/
# List available tags.
git tag --list
# Switch to the version your site is using.
git checkout {your-tag}
# Go back to a previous directory.
cd ..
# Run it without arguments to get a help message.
sudo ./treasuremap/tools/airship

Manifests Preparation

When you do any configuration changes to the manifests, there are a few commands that you can use to validate the changes without uploading them to the Airship environment.

Run lint command for your site; it helps to catch the errors related to documents duplication, broken references, etc.

Example:

sudo ./treasuremap/tools/airship pegleg site -r airship-treasuremap/ \
    lint {site-name}

If you create configuration overrides or do changes to substitutions, it is recommended to run render command this command merges the layers and renders all substitutions. This allows finding what parameters are passed to Helm as overrides for Charts' defaults.

Example:

# Saves the result into rendered.txt file.
sudo ./treasuremap/tools/airship pegleg site -r treasuremap/ \
    render -o rendered.txt ${SITE}

Deployment Failure

During the deployment, it is important to identify a specific step where it fails, there are two major deployment steps:

1. Drydock build: deploys Operating System.
2. Armada build: deploys Helm Charts.

After Configuring Airship CLI, setup credentials for accessing Shipyard; the password is stored in ucp_shipyard_keystone_password secret, you can find it in site/seaworthy/secrets/passphrases/ucp_shipyard_keystone_password.yaml configuration file of your site.

export OS_USERNAME=shipyard
export OS_PASSWORD={shipyard_password}

Now you can use the following commands to access Shipyard:

# Get all actions that were executed on you environment.
sudo ./treasuremap/tools/airship shipyard get actions
# Show all the steps within the action.
sudo ./treasuremap/tools/airship shipyard describe action/{action_id}
# Get a bit more details on the step.
sudo ./treasuremap/tools/airship shipyard describe step/{action_id}/armada_build
# Print the logs from the step.
sudo ./treasuremap/tools/airship shipyard logs step/{action_id}/armada_build

After the failed step is determined, you can access the logs of a specific service (e.g., drydock-api/maas or armada-api) to get more information on the failure, note that there may be multiple pods of a single service running, you need to check all of them to find where the most recent logs are available.

Example of accessing Armada API logs:

# Get all pods running on the cluster and find a name of the pod you are
# interested in.
kubectl get pods -o wide --all-namespaces

# See the logs of specific pod.
kubectl logs -n ucp -f --tail 200 armada-api-d5f757d5-6z6nv

In some cases you want to restart your pod, there is no dedicated command for that in Kubernetes. However, you can delete the pod, it will be restarted by Kubernetes to satisfy replication factor.

# Restart Armada API service.
kubectl delete pod -n ucp armada-api-d5f757d5-6z6nv