Add bifrost manifest

Add class to manage bifrost:
 - clones bifrost from source
 - adds config files
 - runs bifrost install procedure
 - runs custom ansible playbook to generate static dhcp inventory
 - starts an additional dnsmasq instance and runs it like a service

Based on the ironic::bifrost class[1] but with some modifications to
avoid heavy reliance on the puppet DSL.

Co-Authored-By: Clint Byrum <clint@fewbar.com>
Co-Authored-By: greghaynes <greg@greghaynes.net>
Co-Authored-By: Ricardo Carrillo Cruz <ricardo.carrillo.cruz@gmail.com>
Co-Authored-By: Yolanda Robla <info@ysoft.biz>

[1] http://git.openstack.org/cgit/openstack/puppet-ironic/tree/manifests/bifrost.pp

Change-Id: I949344c16cf9ee3965b0bc96850eb208ac65b168

files/dhcp-host.j2

@@ -0,0 +1 @@
+{{ nics[0]['mac'] }},{{ipv4_public_address}},{{name}},12h

files/elements/infra-cloud-networking/element-deps

@@ -0,0 +1,2 @@
+install-static
+package-installs

files/elements/infra-cloud-networking/package-installs.yaml

@@ -0,0 +1,4 @@
+bridge-utils:
+isc-dhcp-client:
+net-tools:
+vlan:

files/elements/infra-cloud-networking/static/etc/network/interfaces

@@ -0,0 +1,4 @@
+# interfaces(5) file used by ifup(8) and ifdown(8)
+# Include files from /etc/network/interfaces.d:
+source-directory /etc/network/interfaces.d
+source /etc/network/interfaces.d/*.cfg

files/elements/puppet/install.d/05-puppet

@@ -0,0 +1,13 @@
+#!/bin/bash
+
+wget https://git.openstack.org/cgit/openstack-infra/system-config/plain/install_puppet.sh
+bash -x install_puppet.sh
+
+mkdir /root/.ssh
+chmod 700 /root/.ssh
+
+cat > /root/.ssh/authorized_keys <<EOF
+from="puppetmaster.openstack.org" ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQDSLlN41ftgxkNeUi/kATYPwMPjJdMaSbgokSb9PSkRPZE7GeNai60BCfhu+ky8h5eMe70Bpwb7mQ7GAtHGXPNU1SRBPhMuVN9EYrQbt5KSiwuiTXtQHsWyYrSKtB+XGbl2PhpMQ/TPVtFoL5usxu/MYaakVkCEbt5IbPYNg88/NKPixicJuhi0qsd+l1X1zoc1+Fn87PlwMoIgfLIktwaL8hw9mzqr+pPcDIjCFQQWnjqJVEObOcMstBT20XwKj/ymiH+6p123nnlIHilACJzXhmIZIZO+EGkNF7KyXpcBSfv9efPI+VCE2TOv/scJFdEHtDFkl2kdUBYPC0wQ92rp puppet-remote-2014-09-15
+EOF
+
+chmod 600 /root/.ssh/authorized_keys

manifests/bifrost.pp

@@ -0,0 +1,194 @@
+# Copyright 2014 Hewlett-Packard Development Company, L.P.
+#
+# Licensed under the Apache License, Version 2.0 (the "License"); you may
+# not use this file except in compliance with the License. You may obtain
+# a copy of the License at
+#
+#      http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+# WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
+# License for the specific language governing permissions and limitations
+# under the License.
+#
+class infracloud::bifrost (
+  $ironic_inventory,
+  $ironic_db_password,
+  $mysql_password,
+  $region,
+  $ipmi_passwords,
+  $ssh_public_key,
+  $ssh_private_key,
+  $vlan,
+  $gateway_ip,
+) {
+
+  # The configdrive bifrost task defaults to copying the user's local public
+  # ssh key. Let's make sure it's there so that bifrost doesn't error and so we
+  # can log in to nodes from the baremetal host.
+  file { '/root/.ssh/id_rsa':
+    ensure  => present,
+    mode    => '0600',
+    content => $ssh_private_key,
+    before  => Exec['install bifrost'],
+  }
+
+  file { '/root/.ssh/id_rsa.pub':
+    ensure  => present,
+    mode    => '0644',
+    content => $ssh_public_key,
+    before  => Exec['install bifrost'],
+  }
+
+  include ::ansible
+
+  class { '::mysql::server':
+    root_password => $mysql_password,
+  }
+
+  vcsrepo { '/opt/stack/bifrost':
+    ensure   => 'latest',
+    provider => 'git',
+    revision => 'master',
+    source   => 'https://git.openstack.org/openstack/bifrost',
+  }
+
+  file { '/etc/bifrost':
+    ensure => directory,
+  }
+
+  file { '/etc/bifrost/bifrost_global_vars':
+    ensure  => present,
+    content => template("infracloud/bifrost/bifrost_global_vars.${region}.erb"),
+  }
+
+  file { '/opt/stack/baremetal.json':
+    ensure  => file,
+    content => template("infracloud/bifrost/inventory.${region}.json.erb"),
+    require => Vcsrepo['/opt/stack/bifrost'],
+  }
+
+  package { 'uuid-runtime':
+    ensure => installed
+  }
+
+  exec { 'install bifrost dependencies':
+    command     => 'pip install -U -r /opt/stack/bifrost/requirements.txt',
+    path        => '/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin',
+    refreshonly => true,
+    subscribe   => Vcsrepo['/opt/stack/bifrost'],
+  }
+
+  file { '/opt/stack/elements':
+    ensure  => directory,
+    recurse => true,
+    source  => 'puppet:///modules/infracloud/elements',
+    require => Vcsrepo['/opt/stack/bifrost'],
+    before  => Exec['install bifrost'],
+  }
+
+  file { '/opt/stack/elements/infra-cloud-networking/static/etc/network/interfaces.d/eth2.cfg':
+    ensure  => file,
+    content => template('infracloud/bifrost/interfaces.d/eth2.cfg.erb'),
+    require => File['/opt/stack/elements'],
+  }
+  file { "/opt/stack/elements/infra-cloud-networking/static/etc/network/interfaces.d/eth2.${vlan}.cfg":
+    ensure  => file,
+    content => template('infracloud/bifrost/interfaces.d/eth2.tag.cfg.erb'),
+    require => File['/opt/stack/elements'],
+  }
+  file { "/opt/stack/elements/infra-cloud-networking/static/etc/network/interfaces.d/br-vlan${vlan}.cfg":
+    ensure  => file,
+    content => template('infracloud/bifrost/interfaces.d/br-vlan.tag.cfg.erb'),
+    require => File['/opt/stack/elements'],
+  }
+
+  exec { 'install bifrost':
+    environment => ['BIFROST_INVENTORY_SOURCE=/opt/stack/baremetal.json', 'HOME=/root'],
+    command     => "ansible-playbook -e @/etc/bifrost/bifrost_global_vars -vvvv \
+                     -i /opt/stack/bifrost/playbooks/inventory/bifrost_inventory.py \
+                     /opt/stack/bifrost/playbooks/install.yaml \
+                     && touch /var/run/bifrost_install_succeeded",
+    path        => '/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin',
+    creates     => '/var/run/bifrost_install_succeeded',
+    timeout     => 1500,
+    require     => [
+      Exec['install bifrost dependencies'],
+      File['/etc/bifrost/bifrost_global_vars'],
+      Vcsrepo['/opt/stack/bifrost'],
+      Package['uuid-runtime'],
+      Class['::mysql::server'],
+    ],
+  }
+
+  if $region == 'hpuswest' {
+    # This is a temporary workaround while we work on getting glean and
+    # networking init scripts working. dnsmasq was already started by bifrost,
+    # but we need a second one in order to make our infra-cloud-networking
+    # element work properly. Set up an alternate config file and static dhcp host
+    # files, and manage the second dnsmasq as if it was a service.
+    #
+    # This improvement is already activated in hpuseast, so this conditional
+    # will make it easier to run both concurrently and eventually remove this
+    # whole thing.
+    file { "/etc/dnsmasq.conf.vlan${vlan}":
+      ensure  => present,
+      content => template('infracloud/bifrost/dnsmasq.conf.vlan.erb'),
+      mode    => '0644',
+      require => Exec['install bifrost'],
+      notify  => Service['dnsmasq-vlan'],
+    }
+
+    file { '/opt/stack/custom_playbooks':
+      ensure  => directory,
+      require => Exec['install bifrost'],
+    }
+
+    file { '/opt/stack/custom_playbooks/templates':
+      ensure => directory,
+    }
+
+    file { '/opt/stack/custom_playbooks/deploy-public-dnsmasq.yaml':
+      ensure  => present,
+      content => template('infracloud/bifrost/deploy-public-dnsmasq.yaml.erb')
+    }
+
+    file { '/opt/stack/custom_playbooks/templates/dhcp-host.j2':
+      ensure => present,
+      source => 'puppet:///modules/infracloud/dhcp-host.j2',
+    }
+
+    file { '/etc/dnsmasq.d/bifrost.dhcp-hosts.vlan${vlan}.d':
+      ensure  => directory,
+      require => Exec['install bifrost'],
+    }
+
+    exec { 'set up static dhcp hosts':
+      environment => ['BIFROST_INVENTORY_SOURCE=/opt/stack/baremetal.json', 'HOME=/root'],
+      command     => "ansible-playbook -e @/etc/bifrost/bifrost_global_vars -vvvv \
+                       -i /opt/stack/bifrost/playbooks/inventory/bifrost_inventory.py \
+                       /opt/stack/custom_playbooks/deploy-public-dnsmasq.yaml",
+      path        => '/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin',
+      unless      => "test '\$(ls -A /etc/dnsmasq.d/bifrost.dhcp-hosts.vlan${vlan}.d/)'", # onlyif directory is empty
+      notify      => Service['dnsmasq-vlan'],
+      require     => [
+        File['/opt/stack/custom_playbooks/deploy-public-dnsmasq.yaml'],
+        File['/opt/stack/custom_playbooks/templates/dhcp-host.j2'],
+        File['/etc/dnsmasq.d/bifrost.dhcp-hosts.vlan${vlan}.d'],
+      ]
+    }
+
+    service { 'dnsmasq-vlan':
+      ensure     => running,
+      provider   => 'base',
+      binary     => "/usr/sbin/dnsmasq --conf-file=/etc/dnsmasq.conf.vlan${vlan}",
+      hasstatus  => false,
+      hasrestart => false,
+      # This uses the process table to TERM the dnsmasq process matching the
+      # pattern parameter. It does not HUP because that would not reload
+      # /etc/dnsmasq.conf.vlan${vlan}.
+      pattern    => "dnsmasq --conf-file=/etc/dnsmasq.conf.vlan${vlan}"
+    }
+  }
+}

templates/bifrost/bifrost_global_vars.hpuswest.erb

@@ -0,0 +1,22 @@
+network_interface: eth2
+node_default_network_interface: eth2
+node_network_info: "{}"
+ipv4_subnet_mask: 255.255.255.192
+ipv4_gateway: <%= @ipaddress_eth2 %>
+ipv4_nameserver: 8.8.8.8
+addressing_mode: "dhcp"
+dhcp_pool_start: 10.10.16.144
+dhcp_pool_end: 10.10.16.190
+inventory_dhcp: true
+dib_os_element: "ubuntu-minimal"
+dib_packages: "openssh-server,vlan,vim,less,bridge-utils"
+dib_trace: true
+extra_dib_elements: "devuser infra-cloud-networking puppet growroot"
+mysql_password: <%= @mysql_password %>
+ironic_db_password: <%= @ironic_db_password %>
+dib_env_vars:
+  DIB_INSTALLTYPE_simple_init: repo
+  DIB_DEV_USER_USERNAME: "baremetal"
+  DIB_DEV_USER_PWDLESS_SUDO: "Y"
+  ELEMENTS_PATH: "/opt/stack/diskimage-builder/elements:/opt/stack/elements:/opt/project-config/nodepool/elements"
+extra_kernel_options: intel_iommu=off

templates/bifrost/deploy-public-dnsmasq.yaml.erb

@@ -0,0 +1,9 @@
+---
+- hosts: baremetal
+  connection: local
+  name: "Set up public dnsmasq"
+  become: no
+  tasks:
+  - name: "Set up static dhcp files"
+    template: src=templates/dhcp-host.j2 dest=/etc/dnsmasq.d/bifrost.dhcp-hosts.vlan<%= @vlan -%>.d/{{ inventory_hostname }}
+    delegate_to: localhost

templates/bifrost/dnsmasq.conf.vlan.erb

@@ -0,0 +1,639 @@
+# Configuration file for dnsmasq.
+#
+# Format is one option per line, legal options are the same
+# as the long options legal on the command line. See
+# "/usr/sbin/dnsmasq --help" or "man 8 dnsmasq" for details.
+
+# Listen on this specific port instead of the standard DNS port
+# (53). Setting this to zero completely disables DNS function,
+# leaving only DHCP and/or TFTP.
+port=0
+
+# The following two options make you a better netizen, since they
+# tell dnsmasq to filter out queries which the public DNS cannot
+# answer, and which load the servers (especially the root servers)
+# unnecessarily. If you have a dial-on-demand link they also stop
+# these requests from bringing up the link unnecessarily.
+
+# Never forward plain names (without a dot or domain part)
+#domain-needed
+# Never forward addresses in the non-routed address spaces.
+#bogus-priv
+
+
+# Uncomment this to filter useless windows-originated DNS requests
+# which can trigger dial-on-demand links needlessly.
+# Note that (amongst other things) this blocks all SRV requests,
+# so don't use it if you use eg Kerberos, SIP, XMMP or Google-talk.
+# This option only affects forwarding, SRV records originating for
+# dnsmasq (via srv-host= lines) are not suppressed by it.
+#filterwin2k
+
+# Change this line if you want dns to get its upstream servers from
+# somewhere other that /etc/resolv.conf
+#resolv-file=
+
+# By  default,  dnsmasq  will  send queries to any of the upstream
+# servers it knows about and tries to favour servers to are  known
+# to  be  up.  Uncommenting this forces dnsmasq to try each query
+# with  each  server  strictly  in  the  order  they   appear   in
+# /etc/resolv.conf
+#strict-order
+
+# If you don't want dnsmasq to read /etc/resolv.conf or any other
+# file, getting its servers from this file instead (see below), then
+# uncomment this.
+#no-resolv
+
+# If you don't want dnsmasq to poll /etc/resolv.conf or other resolv
+# files for changes and re-read them then uncomment this.
+#no-poll
+
+# Add other name servers here, with domain specs if they are for
+# non-public domains.
+#server=/localnet/192.168.0.1
+
+# Example of routing PTR queries to nameservers: this will send all
+# address->name queries for 192.168.3/24 to nameserver 10.1.2.3
+#server=/3.168.192.in-addr.arpa/10.1.2.3
+
+# Add local-only domains here, queries in these domains are answered
+# from /etc/hosts or DHCP only.
+#local=/localnet/
+
+# Add domains which you want to force to an IP address here.
+# The example below send any host in double-click.net to a local
+# web-server.
+#address=/double-click.net/127.0.0.1
+
+# --address (and --server) work with IPv6 addresses too.
+#address=/www.thekelleys.org.uk/fe80::20d:60ff:fe36:f83
+
+# Add the IPs of all queries to yahoo.com, google.com, and their
+# subdomains to the vpn and search ipsets:
+#ipset=/yahoo.com/google.com/vpn,search
+
+# You can control how dnsmasq talks to a server: this forces
+# queries to 10.1.2.3 to be routed via eth1
+# server=10.1.2.3@eth1
+
+# and this sets the source (ie local) address used to talk to
+# 10.1.2.3 to 192.168.1.1 port 55 (there must be a interface with that
+# IP on the machine, obviously).
+# server=10.1.2.3@192.168.1.1#55
+
+# If you want dnsmasq to change uid and gid to something other
+# than the default, edit the following lines.
+#user=
+#group=
+
+# If you want dnsmasq to listen for DHCP and DNS requests only on
+# specified interfaces (and the loopback) give the name of the
+# interface (eg eth0) here.
+# Repeat the line for more than one interface.
+interface=br-vlan<%= @vlan %>
+# Or you can specify which interface _not_ to listen on
+#except-interface=
+except-interface=lo
+# Or which to listen on by address (remember to include 127.0.0.1 if
+# you use this.)
+#listen-address=
+# If you want dnsmasq to provide only DNS service on an interface,
+# configure it as shown above, and then use the following line to
+# disable DHCP and TFTP on it.
+#no-dhcp-interface=
+
+# On systems which support it, dnsmasq binds the wildcard address,
+# even when it is listening on only some interfaces. It then discards
+# requests that it shouldn't reply to. This has the advantage of
+# working even when interfaces come and go and change address. If you
+# want dnsmasq to really bind only the interfaces it is listening on,
+# uncomment this option. About the only time you may need this is when
+# running another nameserver on the same machine.
+bind-interfaces
+
+# If you don't want dnsmasq to read /etc/hosts, uncomment the
+# following line.
+#no-hosts
+# or if you want it to read another file, as well as /etc/hosts, use
+# this.
+#addn-hosts=/etc/banner_add_hosts
+addn-hosts=/etc/dnsmasq.d/bifrost.hosts.vlan<%= @vlan -%>.d
+dhcp-hostsfile=/etc/dnsmasq.d/bifrost.dhcp-hosts.vlan<%= @vlan -%>.d
+
+# Set this (and domain: see below) if you want to have a domain
+# automatically added to simple names in a hosts-file.
+#expand-hosts
+
+# Set the domain for dnsmasq. this is optional, but if it is set, it
+# does the following things.
+# 1) Allows DHCP hosts to have fully qualified domain names, as long
+#     as the domain part matches this setting.
+# 2) Sets the "domain" DHCP option thereby potentially setting the
+#    domain of all systems configured by DHCP
+# 3) Provides the domain part for "expand-hosts"
+#domain=thekelleys.org.uk
+
+# Set a different domain for a particular subnet
+#domain=wireless.thekelleys.org.uk,192.168.2.0/24
+
+# Same idea, but range rather than subnet
+#domain=reserved.thekelleys.org.uk,192.68.3.100,192.168.3.200
+
+# Uncomment this to enable the integrated DHCP server, you need
+# to supply the range of addresses available for lease and optionally
+# a lease time. If you have more than one network, you will need to
+# repeat this for each network on which you want to supply DHCP
+# service.
+
+# This is an example of a DHCP range where the netmask is given. This
+# is needed for networks we reach the dnsmasq DHCP server via a relay
+# agent. If you don't know what a DHCP relay agent is, you probably
+# don't need to worry about this.
+#dhcp-range=192.168.0.50,192.168.0.150,255.255.255.0,12h
+dhcp-range=15.184.52.0,static
+
+# This is an example of a DHCP range which sets a tag, so that
+# some DHCP options may be set only for this network.
+#dhcp-range=set:red,192.168.0.50,192.168.0.150
+
+# Use this DHCP range only when the tag "green" is set.
+#dhcp-range=tag:green,192.168.0.50,192.168.0.150,12h
+
+# Specify a subnet which can't be used for dynamic address allocation,
+# is available for hosts with matching --dhcp-host lines. Note that
+# dhcp-host declarations will be ignored unless there is a dhcp-range
+# of some type for the subnet in question.
+# In this case the netmask is implied (it comes from the network
+# configuration on the machine running dnsmasq) it is possible to give
+# an explicit netmask instead.
+#dhcp-range=192.168.0.0,static
+
+# Enable DHCPv6. Note that the prefix-length does not need to be specified
+# and defaults to 64 if missing/
+#dhcp-range=1234::2, 1234::500, 64, 12h
+
+# Do Router Advertisements, BUT NOT DHCP for this subnet.
+#dhcp-range=1234::, ra-only 
+
+# Do Router Advertisements, BUT NOT DHCP for this subnet, also try and
+# add names to the DNS for the IPv6 address of SLAAC-configured dual-stack 
+# hosts. Use the DHCPv4 lease to derive the name, network segment and 
+# MAC address and assume that the host will also have an
+# IPv6 address calculated using the SLAAC alogrithm.
+#dhcp-range=1234::, ra-names
+
+# Do Router Advertisements, BUT NOT DHCP for this subnet.
+# Set the lifetime to 46 hours. (Note: minimum lifetime is 2 hours.)
+#dhcp-range=1234::, ra-only, 48h
+
+# Do DHCP and Router Advertisements for this subnet. Set the A bit in the RA
+# so that clients can use SLAAC addresses as well as DHCP ones.
+#dhcp-range=1234::2, 1234::500, slaac
+
+# Do Router Advertisements and stateless DHCP for this subnet. Clients will
+# not get addresses from DHCP, but they will get other configuration information.
+# They will use SLAAC for addresses.
+#dhcp-range=1234::, ra-stateless
+
+# Do stateless DHCP, SLAAC, and generate DNS names for SLAAC addresses
+# from DHCPv4 leases.
+#dhcp-range=1234::, ra-stateless, ra-names
+
+# Do router advertisements for all subnets where we're doing DHCPv6
+# Unless overriden by ra-stateless, ra-names, et al, the router 
+# advertisements will have the M and O bits set, so that the clients
+# get addresses and configuration from DHCPv6, and the A bit reset, so the 
+# clients don't use SLAAC addresses.
+#enable-ra
+
+# Supply parameters for specified hosts using DHCP. There are lots
+# of valid alternatives, so we will give examples of each. Note that
+# IP addresses DO NOT have to be in the range given above, they just
+# need to be on the same network. The order of the parameters in these
+# do not matter, it's permissible to give name, address and MAC in any
+# order.
+
+# Always allocate the host with Ethernet address 11:22:33:44:55:66
+# The IP address 192.168.0.60
+#dhcp-host=11:22:33:44:55:66,192.168.0.60
+
+# Always set the name of the host with hardware address
+# 11:22:33:44:55:66 to be "fred"
+#dhcp-host=11:22:33:44:55:66,fred
+
+# Always give the host with Ethernet address 11:22:33:44:55:66
+# the name fred and IP address 192.168.0.60 and lease time 45 minutes
+#dhcp-host=11:22:33:44:55:66,fred,192.168.0.60,45m
+
+# Give a host with Ethernet address 11:22:33:44:55:66 or
+# 12:34:56:78:90:12 the IP address 192.168.0.60. Dnsmasq will assume
+# that these two Ethernet interfaces will never be in use at the same
+# time, and give the IP address to the second, even if it is already
+# in use by the first. Useful for laptops with wired and wireless
+# addresses.
+#dhcp-host=11:22:33:44:55:66,12:34:56:78:90:12,192.168.0.60
+
+# Give the machine which says its name is "bert" IP address
+# 192.168.0.70 and an infinite lease
+#dhcp-host=bert,192.168.0.70,infinite
+
+# Always give the host with client identifier 01:02:02:04
+# the IP address 192.168.0.60
+#dhcp-host=id:01:02:02:04,192.168.0.60
+
+# Always give the host with client identifier "marjorie"
+# the IP address 192.168.0.60
+#dhcp-host=id:marjorie,192.168.0.60
+
+# Enable the address given for "judge" in /etc/hosts
+# to be given to a machine presenting the name "judge" when
+# it asks for a DHCP lease.
+#dhcp-host=judge
+
+# Never offer DHCP service to a machine whose Ethernet
+# address is 11:22:33:44:55:66
+#dhcp-host=11:22:33:44:55:66,ignore
+
+# Ignore any client-id presented by the machine with Ethernet
+# address 11:22:33:44:55:66. This is useful to prevent a machine
+# being treated differently when running under different OS's or
+# between PXE boot and OS boot.
+#dhcp-host=11:22:33:44:55:66,id:*
+
+# Send extra options which are tagged as "red" to
+# the machine with Ethernet address 11:22:33:44:55:66
+#dhcp-host=11:22:33:44:55:66,set:red
+
+# Send extra options which are tagged as "red" to
+# any machine with Ethernet address starting 11:22:33:
+#dhcp-host=11:22:33:*:*:*,set:red
+
+# Give a fixed IPv6 address and name to client with 
+# DUID 00:01:00:01:16:d2:83:fc:92:d4:19:e2:d8:b2
+# Note the MAC addresses CANNOT be used to identify DHCPv6 clients.
+# Note also the they [] around the IPv6 address are obilgatory.
+#dhcp-host=id:00:01:00:01:16:d2:83:fc:92:d4:19:e2:d8:b2, fred, [1234::5] 
+
+# Ignore any clients which are not specified in dhcp-host lines
+# or /etc/ethers. Equivalent to ISC "deny unknown-clients".
+# This relies on the special "known" tag which is set when
+# a host is matched.
+#dhcp-ignore=tag:!known
+
+# Send extra options which are tagged as "red" to any machine whose
+# DHCP vendorclass string includes the substring "Linux"
+#dhcp-vendorclass=set:red,Linux
+
+# Send extra options which are tagged as "red" to any machine one
+# of whose DHCP userclass strings includes the substring "accounts"
+#dhcp-userclass=set:red,accounts
+
+# Send extra options which are tagged as "red" to any machine whose
+# MAC address matches the pattern.
+#dhcp-mac=set:red,00:60:8C:*:*:*
+
+# If this line is uncommented, dnsmasq will read /etc/ethers and act
+# on the ethernet-address/IP pairs found there just as if they had
+# been given as --dhcp-host options. Useful if you keep
+# MAC-address/host mappings there for other purposes.
+#read-ethers
+
+# Send options to hosts which ask for a DHCP lease.
+# See RFC 2132 for details of available options.
+# Common options can be given to dnsmasq by name:
+# run "dnsmasq --help dhcp" to get a list.
+# Note that all the common settings, such as netmask and
+# broadcast address, DNS server and default route, are given
+# sane defaults by dnsmasq. You very likely will not need
+# any dhcp-options. If you use Windows clients and Samba, there
+# are some options which are recommended, they are detailed at the
+# end of this section.
+
+# Override the default route supplied by dnsmasq, which assumes the
+# router is the same machine as the one running dnsmasq.
+#dhcp-option=3,1.2.3.4
+
+# Do the same thing, but using the option name
+#dhcp-option=option:router,1.2.3.4
+
+# Override the default route supplied by dnsmasq and send no default
+# route at all. Note that this only works for the options sent by
+# default (1, 3, 6, 12, 28) the same line will send a zero-length option
+# for all other option numbers.
+#dhcp-option=3
+
+# Set the NTP time server addresses to 192.168.0.4 and 10.10.0.5
+#dhcp-option=option:ntp-server,192.168.0.4,10.10.0.5
+
+# Send DHCPv6 option. Note [] around IPv6 addresses.
+#dhcp-option=option6:dns-server,[1234::77],[1234::88]
+
+# Send DHCPv6 option for namservers as the machine running 
+# dnsmasq and another.
+#dhcp-option=option6:dns-server,[::],[1234::88]
+
+# Ask client to poll for option changes every six hours. (RFC4242)
+#dhcp-option=option6:information-refresh-time,6h
+
+# Set the NTP time server address to be the same machine as
+# is running dnsmasq
+#dhcp-option=42,0.0.0.0
+
+# Set the NIS domain name to "welly"
+#dhcp-option=40,welly
+
+# Set the default time-to-live to 50
+#dhcp-option=23,50
+
+# Set the "all subnets are local" flag
+#dhcp-option=27,1
+
+# Send the etherboot magic flag and then etherboot options (a string).
+#dhcp-option=128,e4:45:74:68:00:00
+#dhcp-option=129,NIC=eepro100
+
+# Specify an option which will only be sent to the "red" network
+# (see dhcp-range for the declaration of the "red" network)
+# Note that the tag: part must precede the option: part.
+#dhcp-option = tag:red, option:ntp-server, 192.168.1.1
+
+# The following DHCP options set up dnsmasq in the same way as is specified
+# for the ISC dhcpcd in
+# http://www.samba.org/samba/ftp/docs/textdocs/DHCP-Server-Configuration.txt
+# adapted for a typical dnsmasq installation where the host running
+# dnsmasq is also the host running samba.
+# you may want to uncomment some or all of them if you use
+# Windows clients and Samba.
+#dhcp-option=19,0           # option ip-forwarding off
+#dhcp-option=44,0.0.0.0     # set netbios-over-TCP/IP nameserver(s) aka WINS server(s)
+#dhcp-option=45,0.0.0.0     # netbios datagram distribution server
+#dhcp-option=46,8           # netbios node type
+
+# Send an empty WPAD option. This may be REQUIRED to get windows 7 to behave.
+#dhcp-option=252,"\n"
+
+# Send RFC-3397 DNS domain search DHCP option. WARNING: Your DHCP client
+# probably doesn't support this......
+#dhcp-option=option:domain-search,eng.apple.com,marketing.apple.com
+
+# Send RFC-3442 classless static routes (note the netmask encoding)
+#dhcp-option=121,192.168.1.0/24,1.2.3.4,10.0.0.0/8,5.6.7.8
+
+# Send vendor-class specific options encapsulated in DHCP option 43.
+# The meaning of the options is defined by the vendor-class so
+# options are sent only when the client supplied vendor class
+# matches the class given here. (A substring match is OK, so "MSFT"
+# matches "MSFT" and "MSFT 5.0"). This example sets the
+# mtftp address to 0.0.0.0 for PXEClients.
+#dhcp-option=vendor:PXEClient,1,0.0.0.0
+
+# Send microsoft-specific option to tell windows to release the DHCP lease
+# when it shuts down. Note the "i" flag, to tell dnsmasq to send the
+# value as a four-byte integer - that's what microsoft wants. See
+# http://technet2.microsoft.com/WindowsServer/en/library/a70f1bb7-d2d4-49f0-96d6-4b7414ecfaae1033.mspx?mfr=true
+#dhcp-option=vendor:MSFT,2,1i
+
+# Send the Encapsulated-vendor-class ID needed by some configurations of
+# Etherboot to allow is to recognise the DHCP server.
+#dhcp-option=vendor:Etherboot,60,"Etherboot"
+
+# Send options to PXELinux. Note that we need to send the options even
+# though they don't appear in the parameter request list, so we need
+# to use dhcp-option-force here.
+# See http://syslinux.zytor.com/pxe.php#special for details.
+# Magic number - needed before anything else is recognised
+#dhcp-option-force=208,f1:00:74:7e
+# Configuration file name
+#dhcp-option-force=209,configs/common
+# Path prefix
+#dhcp-option-force=210,/tftpboot/pxelinux/files/
+# Reboot time. (Note 'i' to send 32-bit value)
+#dhcp-option-force=211,30i
+
+# Set the boot filename for netboot/PXE. You will only need
+# this is you want to boot machines over the network and you will need
+# a TFTP server; either dnsmasq's built in TFTP server or an
+# external one. (See below for how to enable the TFTP server.)
+#dhcp-boot=pxelinux.0
+#dhcp-boot=/tftpboot/undionly.kpxe
+
+# The same as above, but use custom tftp-server instead machine running dnsmasq
+#dhcp-boot=pxelinux,server.name,192.168.1.100
+
+# Boot for Etherboot gPXE. The idea is to send two different
+# filenames, the first loads gPXE, and the second tells gPXE what to
+# load. The dhcp-match sets the gpxe tag for requests from gPXE.
+#dhcp-userclass=set:gpxe,"gPXE"
+#dhcp-boot=tag:gpxe,/ipxe.pxe
+
+#dhcp-match=set:ipxe,175 # iPXE sends a 175 option.
+#dhcp-boot=tag:!ipxe,/undionly.kpxe
+#dhcp-boot=http://15.184.52.3:8080/boot.ipxe
+
+# Encapsulated options for Etherboot gPXE. All the options are
+# encapsulated within option 175
+#dhcp-option=encap:175, 1, 5b         # priority code
+#dhcp-option=encap:175, 176, 1b       # no-proxydhcp
+#dhcp-option=encap:175, 177, string   # bus-id
+#dhcp-option=encap:175, 189, 1b       # BIOS drive code
+#dhcp-option=encap:175, 190, user     # iSCSI username
+#dhcp-option=encap:175, 191, pass     # iSCSI password
+
+# Test for the architecture of a netboot client. PXE clients are
+# supposed to send their architecture as option 93. (See RFC 4578)
+#dhcp-match=peecees, option:client-arch, 0 #x86-32
+#dhcp-match=itanics, option:client-arch, 2 #IA64
+#dhcp-match=hammers, option:client-arch, 6 #x86-64
+#dhcp-match=mactels, option:client-arch, 7 #EFI x86-64
+
+# Do real PXE, rather than just booting a single file, this is an
+# alternative to dhcp-boot.
+#pxe-prompt="What system shall I netboot?"
+# or with timeout before first available action is taken:
+#pxe-prompt="Press F8 for menu.", 60
+
+# Available boot services. for PXE.
+#pxe-service=x86PC, "Boot from local disk"
+
+# Loads <tftp-root>/pxelinux.0 from dnsmasq TFTP server.
+#pxe-service=x86PC, "Install Linux", pxelinux
+
+# Loads <tftp-root>/pxelinux.0 from TFTP server at 1.2.3.4.
+# Beware this fails on old PXE ROMS.
+#pxe-service=x86PC, "Install Linux", pxelinux, 1.2.3.4
+
+# Use bootserver on network, found my multicast or broadcast.
+#pxe-service=x86PC, "Install windows from RIS server", 1
+
+# Use bootserver at a known IP address.
+#pxe-service=x86PC, "Install windows from RIS server", 1, 1.2.3.4
+
+# If you have multicast-FTP available,
+# information for that can be passed in a similar way using options 1
+# to 5. See page 19 of
+# http://download.intel.com/design/archives/wfm/downloads/pxespec.pdf
+
+
+# Enable dnsmasq's built-in TFTP server
+#enable-tftp
+
+# Set the root directory for files available via FTP.
+#tftp-root=/var/ftpd
+
+# Make the TFTP server more secure: with this set, only files owned by
+# the user dnsmasq is running as will be send over the net.
+#tftp-secure
+
+# This option stops dnsmasq from negotiating a larger blocksize for TFTP
+# transfers. It will slow things down, but may rescue some broken TFTP
+# clients.
+#tftp-no-blocksize
+
+# Set the boot file name only when the "red" tag is set.
+#dhcp-boot=tag:red,pxelinux.red-net
+
+# An example of dhcp-boot with an external TFTP server: the name and IP
+# address of the server are given after the filename.
+# Can fail with old PXE ROMS. Overridden by --pxe-service.
+#dhcp-boot=/var/ftpd/pxelinux.0,boothost,192.168.0.3
+
+# If there are multiple external tftp servers having a same name
+# (using /etc/hosts) then that name can be specified as the
+# tftp_servername (the third option to dhcp-boot) and in that
+# case dnsmasq resolves this name and returns the resultant IP
+# addresses in round robin fasion. This facility can be used to
+# load balance the tftp load among a set of servers.
+#dhcp-boot=/var/ftpd/pxelinux.0,boothost,tftp_server_name
+
+# Set the limit on DHCP leases, the default is 150
+#dhcp-lease-max=150
+
+# The DHCP server needs somewhere on disk to keep its lease database.
+# This defaults to a sane location, but if you want to change it, use
+# the line below.
+#dhcp-leasefile=/var/lib/misc/dnsmasq.leases
+dhcp-leasefile=/var/lib/misc/dnsmasq.leases.vlan<%= @vlan -%>
+
+# Set the DHCP server to authoritative mode. In this mode it will barge in
+# and take over the lease for any client which broadcasts on the network,
+# whether it has a record of the lease or not. This avoids long timeouts
+# when a machine wakes up on a new network. DO NOT enable this if there's
+# the slightest chance that you might end up accidentally configuring a DHCP
+# server for your campus/company accidentally. The ISC server uses
+# the same option, and this URL provides more information:
+# http://www.isc.org/files/auth.html
+#dhcp-authoritative
+
+# Run an executable when a DHCP lease is created or destroyed.
+# The arguments sent to the script are "add" or "del",
+# then the MAC address, the IP address and finally the hostname
+# if there is one.
+#dhcp-script=/bin/echo
+
+# Set the cachesize here.
+#cache-size=150
+
+# If you want to disable negative caching, uncomment this.
+#no-negcache
+
+# Normally responses which come from /etc/hosts and the DHCP lease
+# file have Time-To-Live set as zero, which conventionally means
+# do not cache further. If you are happy to trade lower load on the
+# server for potentially stale date, you can set a time-to-live (in
+# seconds) here.
+#local-ttl=
+
+# If you want dnsmasq to detect attempts by Verisign to send queries
+# to unregistered .com and .net hosts to its sitefinder service and
+# have dnsmasq instead return the correct NXDOMAIN response, uncomment
+# this line. You can add similar lines to do the same for other
+# registries which have implemented wildcard A records.
+#bogus-nxdomain=64.94.110.11
+
+# If you want to fix up DNS results from upstream servers, use the
+# alias option. This only works for IPv4.
+# This alias makes a result of 1.2.3.4 appear as 5.6.7.8
+#alias=1.2.3.4,5.6.7.8
+# and this maps 1.2.3.x to 5.6.7.x
+#alias=1.2.3.0,5.6.7.0,255.255.255.0
+# and this maps 192.168.0.10->192.168.0.40 to 10.0.0.10->10.0.0.40
+#alias=192.168.0.10-192.168.0.40,10.0.0.0,255.255.255.0
+
+# Change these lines if you want dnsmasq to serve MX records.
+
+# Return an MX record named "maildomain.com" with target
+# servermachine.com and preference 50
+#mx-host=maildomain.com,servermachine.com,50
+
+# Set the default target for MX records created using the localmx option.
+#mx-target=servermachine.com
+
+# Return an MX record pointing to the mx-target for all local
+# machines.
+#localmx
+
+# Return an MX record pointing to itself for all local machines.
+#selfmx
+
+# Change the following lines if you want dnsmasq to serve SRV
+# records.  These are useful if you want to serve ldap requests for
+# Active Directory and other windows-originated DNS requests.
+# See RFC 2782.
+# You may add multiple srv-host lines.
+# The fields are <name>,<target>,<port>,<priority>,<weight>
+# If the domain part if missing from the name (so that is just has the
+# service and protocol sections) then the domain given by the domain=
+# config option is used. (Note that expand-hosts does not need to be
+# set for this to work.)
+
+# A SRV record sending LDAP for the example.com domain to
+# ldapserver.example.com port 389
+#srv-host=_ldap._tcp.example.com,ldapserver.example.com,389
+
+# A SRV record sending LDAP for the example.com domain to
+# ldapserver.example.com port 389 (using domain=)
+#domain=example.com
+#srv-host=_ldap._tcp,ldapserver.example.com,389
+
+# Two SRV records for LDAP, each with different priorities
+#srv-host=_ldap._tcp.example.com,ldapserver.example.com,389,1
+#srv-host=_ldap._tcp.example.com,ldapserver.example.com,389,2
+
+# A SRV record indicating that there is no LDAP server for the domain
+# example.com
+#srv-host=_ldap._tcp.example.com
+
+# The following line shows how to make dnsmasq serve an arbitrary PTR
+# record. This is useful for DNS-SD. (Note that the
+# domain-name expansion done for SRV records _does_not
+# occur for PTR records.)
+#ptr-record=_http._tcp.dns-sd-services,"New Employee Page._http._tcp.dns-sd-services"
+
+# Change the following lines to enable dnsmasq to serve TXT records.
+# These are used for things like SPF and zeroconf. (Note that the
+# domain-name expansion done for SRV records _does_not
+# occur for TXT records.)
+
+#Example SPF.
+#txt-record=example.com,"v=spf1 a -all"
+
+#Example zeroconf
+#txt-record=_http._tcp.example.com,name=value,paper=A4
+
+# Provide an alias for a "local" DNS name. Note that this _only_ works
+# for targets which are names from DHCP or /etc/hosts. Give host
+# "bert" another name, bertrand
+#cname=bertand,bert
+
+# For debugging purposes, log each DNS query as it passes through
+# dnsmasq.
+#log-queries
+
+# Log lots of extra information about DHCP transactions.
+#log-dhcp
+
+# Include another lot of configuration options.
+#conf-file=/etc/dnsmasq.more.conf
+#conf-dir=/etc/dnsmasq.d
+

templates/bifrost/interfaces.d/br-vlan.tag.cfg.erb

@@ -0,0 +1,7 @@
+auto br-vlan<%= @vlan -%>
+iface br-vlan<%= @vlan -%> inet dhcp
+bridge_ports eth2.<%= @vlan -%>
+bridge_hello 2
+bridge_maxage 12
+bridge_stp off
+post-up ip route add default via <%= @gateway_ip -%> dev br-vlan<%= @vlan -%>

templates/bifrost/interfaces.d/eth2.cfg.erb

@@ -0,0 +1,3 @@
+auto eth2
+iface eth2 inet dhcp
+post-up route del default dev eth2

templates/bifrost/interfaces.d/eth2.tag.cfg.erb

@@ -0,0 +1,3 @@
+auto eth2.<%= @vlan -%>
+iface eth2.<%= @vlan -%> inet manual
+vlan-raw-device eth2

templates/bifrost/inventory.hpuswest.json.erb

@@ -0,0 +1,3 @@
+<% @ironic_deployed_inventory = @ironic_inventory.reject { |k,v| v['disabled'] } -%>
+<% @ironic_deployed_inventory.each { |k,v| v['driver_info']['power']['ipmi_password'] = @ipmi_passwords[v['driver_info']['power']['ipmi_address']] } -%>
+<%= JSON.pretty_generate(@ironic_deployed_inventory) %>