fe76077425
Heat relevant contents will be split out from Horizon in Queens release. After this splitting out, Heat-Dashboard must have its own settings in Heat-Dashboard repository. So this review request includes following. - Create own settings under local_settings.d - Add procedure for installing above settings. - Fix installation procedure according to above changes. Change-Id: I0b9a9907cb0c02aed70e7c1af3d9d07b0ddeffb6
63 lines
2.2 KiB
Bash
63 lines
2.2 KiB
Bash
# plugin.sh - DevStack plugin.sh dispatch script heat-dashboard
|
|
|
|
HEAT_DASHBOARD_DIR=$(cd $(dirname $BASH_SOURCE)/.. && pwd)
|
|
|
|
function install_heat_dashboard {
|
|
# NOTE(shu-mutou): workaround for devstack bug: 1540328
|
|
# where devstack install 'test-requirements' but should not do it
|
|
# for heat-dashboard project as it installs Horizon from url.
|
|
# Remove following two 'mv' commands when mentioned bug is fixed.
|
|
mv $HEAT_DASHBOARD_DIR/test-requirements.txt $HEAT_DASHBOARD_DIR/_test-requirements.txt
|
|
|
|
setup_develop ${HEAT_DASHBOARD_DIR}
|
|
|
|
mv $HEAT_DASHBOARD_DIR/_test-requirements.txt $HEAT_DASHBOARD_DIR/test-requirements.txt
|
|
}
|
|
|
|
function configure_heat_dashboard {
|
|
cp -a ${HEAT_DASHBOARD_DIR}/heat_dashboard/enabled/* ${DEST}/horizon/openstack_dashboard/local/enabled/
|
|
cp -a ${HEAT_DASHBOARD_DIR}/heat_dashboard/local_settings.d ${DEST}/horizon/openstack_dashboard/local/local_settings.d/
|
|
cp -a ${HEAT_DASHBOARD_DIR}/etc/heat_policy.json ${DEST}/horizon/openstack_dashboard/conf/
|
|
# NOTE: If locale directory does not exist, compilemessages will fail,
|
|
# so check for an existence of locale directory is required.
|
|
if [ -d ${HEAT_DASHBOARD_DIR}/heat_dashboard/locale ]; then
|
|
(cd ${HEAT_DASHBOARD_DIR}/heat_dashboard; DJANGO_SETTINGS_MODULE=openstack_dashboard.settings ../manage.py compilemessages)
|
|
fi
|
|
}
|
|
|
|
# check for service enabled
|
|
if is_service_enabled heat-dashboard; then
|
|
|
|
if [[ "$1" == "stack" && "$2" == "pre-install" ]]; then
|
|
# Set up system services
|
|
# no-op
|
|
:
|
|
|
|
elif [[ "$1" == "stack" && "$2" == "install" ]]; then
|
|
# Perform installation of service source
|
|
echo_summary "Installing Heat Dashboard"
|
|
install_heat_dashboard
|
|
|
|
elif [[ "$1" == "stack" && "$2" == "post-config" ]]; then
|
|
# Configure after the other layer 1 and 2 services have been configured
|
|
echo_summary "Configuring Heat Dashboard"
|
|
configure_heat_dashboard
|
|
|
|
elif [[ "$1" == "stack" && "$2" == "extra" ]]; then
|
|
# no-op
|
|
:
|
|
fi
|
|
|
|
if [[ "$1" == "unstack" ]]; then
|
|
# no-op
|
|
:
|
|
fi
|
|
|
|
if [[ "$1" == "clean" ]]; then
|
|
# Remove state and transient data
|
|
# Remember clean.sh first calls unstack.sh
|
|
# no-op
|
|
:
|
|
fi
|
|
fi
|