=============== IPMITool driver =============== Overview ======== The IPMI_ (Intelligent Platform Management Interface) drivers manage nodes by using IPMI protocol versions 2.0 or 1.5. They use the IPMItool_ utility which is an open-source command-line interface (CLI) for controlling IPMI-enabled devices. The following hardware types and classic drivers use IPMItool for power and management: * hardware types: * ``ipmi`` * classic drivers: * ``agent_ipmitool`` * ``pxe_ipmitool`` * ``agent_ipmitool_socat`` * ``pxe_ipmitool_socat`` Glossary ======== * IPMI_ - Intelligent Platform Management Interface. * IPMB - Intelligent Platform Management Bus/Bridge. * BMC_ - Baseboard Management Controller. * RMCP - Remote Management Control Protocol. Enabling the IPMItool driver(s) =============================== Please see :doc:`/install/configure-ipmi` for the required dependencies. #. The ``ipmi`` hardware type is enabled by default starting with the Ocata release. To enable it explicitly, add the following to your ``ironic.conf``: .. code-block:: ini [DEFAULT] enabled_hardware_types = ipmi #. The ``pxe_ipmitool`` classic driver is enabled by default. To enable one or more of the other IPMI classic drivers, add them to the ``enabled_drivers`` configuration option in your ``ironic.conf``. The following enables ``pxe_ipmitool`` and ``agent_ipmitool`` drivers: .. code-block:: ini [DEFAULT] enabled_drivers = pxe_ipmitool,agent_ipmitool #. Restart the Ironic conductor service. Please see :doc:`/install/enabling-drivers` for more details. Registering a node with the IPMItool driver =========================================== Nodes configured to use the IPMItool drivers should have the ``driver`` field set to ``ipmi`` (hardware type) or to the name of one of the classic drivers that support IPMItool. The following configuration value is required and has to be added to the node's ``driver_info`` field: - ``ipmi_address``: The IP address or hostname of the BMC. Other options may be needed to match the configuration of the BMC, the following options are optional, but in most cases, it's considered a good practice to have them set: - ``ipmi_username``: The username to access the BMC; defaults to *NULL* user. - ``ipmi_password``: The password to access the BMC; defaults to *NULL*. - ``ipmi_port``: The remote IPMI RMCP port. By default ipmitool will use the port *623*. .. note:: It is highly recommend that you setup a username and password for your BMC. The ``openstack baremetal node create`` command can be used to enroll a node with an IPMItool-based driver. For example:: openstack baremetal node create --driver ipmi \ --driver-info ipmi_address=
\ --driver-info ipmi_username= \ --driver-info ipmi_password= Advanced configuration ====================== When a simple configuration such as providing the ``address``, ``username`` and ``password`` is not enough, the IPMItool driver contains many other options that can be used to address special usages. Single/Double bridging functionality ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ .. note:: A version of IPMItool higher or equal to 1.8.12 is required to use the bridging functionality. There are two different bridging functionalities supported by the IPMItool-based drivers: *single* bridge and *dual* bridge. The following configuration values need to be added to the node's ``driver_info`` field so bridging can be used: - ``ipmi_bridging``: The bridging type; default is *no*; other supported values are *single* for single bridge or *dual* for double bridge. - ``ipmi_local_address``: The local IPMB address for bridged requests. Required only if ``ipmi_bridging`` is set to *single* or *dual*. This configuration is optional, if not specified it will be auto discovered by IPMItool. - ``ipmi_target_address``: The destination address for bridged requests. Required only if ``ipmi_bridging`` is set to *single* or *dual*. - ``ipmi_target_channel``: The destination channel for bridged requests. Required only if ``ipmi_bridging`` is set to *single* or *dual*. Double bridge specific options: - ``ipmi_transit_address``: The transit address for bridged requests. Required only if ``ipmi_bridging`` is set to *dual*. - ``ipmi_transit_channel``: The transit channel for bridged requests. Required only if ``ipmi_bridging`` is set to *dual*. The parameter ``ipmi_bridging`` should specify the type of bridging required: *single* or *dual* to access the bare metal node. If the parameter is not specified, the default value will be set to *no*. The ``openstack baremetal node set`` command can be used to set the required bridging information to the Ironic node enrolled with the IPMItool driver. For example: * Single Bridging:: openstack baremetal node set \ --driver-info ipmi_local_address=
\ --driver-info ipmi_bridging=single \ --driver-info ipmi_target_channel= \ --driver-info ipmi_target_address= * Double Bridging:: openstack baremetal node set \ --driver-info ipmi_local_address=
\ --driver-info ipmi_bridging=dual \ --driver-info ipmi_transit_channel= \ --driver-info ipmi_transit_address= \ --driver-info ipmi_target_channel= \ --driver-info ipmi_target_address= Changing the version of the IPMI protocol ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ The IPMItool-based drivers works with the versions *2.0* and *1.5* of the IPMI protocol. By default, the version *2.0* is used. In order to change the IPMI protocol version in the bare metal node, the following option needs to be set to the node's ``driver_info`` field: - ``ipmi_protocol_version``: The version of the IPMI protocol; default is *2.0*. Supported values are *1.5* or *2.0*. The ``openstack baremetal node set`` command can be used to set the desired protocol version:: openstack baremetal node set --driver-info ipmi_protocol_version= .. warning:: Version *1.5* of the IPMI protocol does not support encryption. Therefore, it is highly recommended that version 2.0 is used. .. TODO(lucasagomes): Write about privilege level .. TODO(lucasagomes): Write about force boot device .. _IPMItool: https://sourceforge.net/projects/ipmitool/ .. _IPMI: https://en.wikipedia.org/wiki/Intelligent_Platform_Management_Interface .. _BMC: https://en.wikipedia.org/wiki/Intelligent_Platform_Management_Interface#Baseboard_management_controller