---
# You can use this file to override _any_ variable throughout Kolla.
# Additional options can be found in the 'kolla/ansible/group_vars/all.yml' file.
# Default value of all the commented parameters are shown here, To override
# the default value uncomment the parameter and change its value.

###################
# Kolla options
###################
# Valid options are [ COPY_ONCE, COPY_ALWAYS ]
#config_strategy: "COPY_ALWAYS"

# Valid options are [ centos, oraclelinux, ubuntu ]
#kolla_base_distro: "centos"

# Valid options are [ binary, source ]
#kolla_install_type: "binary"

# Valid option is Docker repository tag
#openstack_release: "3.0.0"

# Location of configuration overrides
#node_custom_config: "/etc/kolla/config"

# This should be a VIP, an unused IP on your network that will float between
# the hosts running keepalived for high-availability. When running an All-In-One
# without haproxy and keepalived, this should be the first IP on your
# 'network_interface' as set in the Networking section below.
kolla_internal_vip_address: "10.10.10.254"

# This is the DNS name that maps to the kolla_internal_vip_address VIP. By
# default it is the same as kolla_internal_vip_address.
#kolla_internal_fqdn: "{{ kolla_internal_vip_address }}"

# This should be a VIP, an unused IP on your network that will float between
# the hosts running keepalived for high-availability. It defaults to the
# kolla_internal_vip_address, allowing internal and external communication to
# share the same address.  Specify a kolla_external_vip_address to separate
# internal and external requests between two VIPs.
#kolla_external_vip_address: "{{ kolla_internal_vip_address }}"

# The Public address used to communicate with OpenStack as set in the public_url
# for the endpoints that will be created. This DNS name should map to
# kolla_external_vip_address.
#kolla_external_fqdn: "{{ kolla_external_vip_address }}"

####################
# Docker options
####################
# Below is an example of a private repository with authentication. Note the
# Docker registry password can also be set in the passwords.yml file.

#docker_registry: "172.16.0.10:4000"
#docker_namespace: "companyname"
#docker_registry_username: "sam"
#docker_registry_password: "correcthorsebatterystaple"


###############################
# Neutron - Networking Options
###############################
# This interface is what all your api services will be bound to by default.
# Additionally, all vxlan/tunnel and storage network traffic will go over this
# interface by default. This interface must contain an IPv4 address.
# It is possible for hosts to have non-matching names of interfaces - these can
# be set in an inventory file per host or per group or stored separately, see
#     http://docs.ansible.com/ansible/intro_inventory.html
# Yet another way to workaround the naming problem is to create a bond for the
# interface on all hosts and give the bond name here. Similar strategy can be
# followed for other types of interfaces.
#network_interface: "eth0"

# These can be adjusted for even more customization. The default is the same as
# the 'network_interface'. These interfaces must contain an IPv4 address.
#kolla_external_vip_interface: "{{ network_interface }}"
#api_interface: "{{ network_interface }}"
#storage_interface: "{{ network_interface }}"
#cluster_interface: "{{ network_interface }}"
#tunnel_interface: "{{ network_interface }}"

# This is the raw interface given to neutron as its external network port. Even
# though an IP address can exist on this interface, it will be unusable in most
# configurations. It is recommended this interface not be configured with any IP
# addresses for that reason.
#neutron_external_interface: "eth1"

# Valid options are [ openvswitch, linuxbridge ]
#neutron_plugin_agent: "openvswitch"


####################
# keepalived options
####################
# Arbitrary unique number from 0..255
#keepalived_virtual_router_id: "51"


####################
# TLS options
####################
# To provide encryption and authentication on the kolla_external_vip_interface,
# TLS can be enabled.  When TLS is enabled, certificates must be provided to
# allow clients to perform authentication.
#kolla_enable_tls_external: "no"
#kolla_external_fqdn_cert: "{{ node_config_directory }}/certificates/haproxy.pem"


####################
# OpenStack options
####################
# Use these options to set the various log levels across all OpenStack projects
# Valid options are [ True, False ]
#openstack_logging_debug: "False"

# Valid options are [ novnc, spice ]
#nova_console: "novnc"

# OpenStack services can be enabled or disabled with these options
#enable_aodh: "no"
#enable_barbican: "no"
#enable_ceilometer: "no"
#enable_central_logging: "no"
#enable_ceph: "no"
#enable_ceph_rgw: "no"
#enable_cinder: "no"
#enable_cinder_backend_iscsi: "no"
#enable_cinder_backend_lvm: "no"
#enable_cloudkitty: "no"
#enable_congress: "no"
#enable_etcd: "no"
#enable_gnocchi: "no"
#enable_grafana: "no"
#enable_heat: "yes"
#enable_horizon: "yes"
#enable_influxdb: "no"
#enable_ironic: "no"
#enable_kuryr: "no"
#enable_magnum: "no"
#enable_manila: "no"
#enable_manila_backend_generic: "no"
#enable_manila_backend_hnas: "no"
#enable_mistral: "no"
#enable_mongodb: "no"
#enable_murano: "no"
#enable_multipathd: "no"
#enable_neutron_dvr: "no"
#enable_neutron_lbaas: "no"
#enable_neutron_fwaas: "no"
#enable_neutron_qos: "no"
#enable_neutron_agent_ha: "no"
#enable_neutron_vpnaas: "no"
#enable_rally: "no"
#enable_sahara: "no"
#enable_searchlight: "no"
#enable_senlin: "no"
#enable_swift: "no"
#enable_telegraf: "no"
#enable_tempest: "no"
#enable_watcher: "no"

###################
# Ceph options
###################
# Ceph can be setup with a caching to improve performance. To use the cache you
# must provide separate disks than those for the OSDs
#ceph_enable_cache: "no"
# Valid options are [ forward, none, writeback ]
#ceph_cache_mode: "writeback"

# A requirement for using the erasure-coded pools is you must setup a cache tier
# Valid options are [ erasure, replicated ]
#ceph_pool_type: "replicated"


##############################
# Keystone - Identity Options
##############################

# Valid options are [ uuid, fernet ]
#keystone_token_provider: 'uuid'

# Interval to rotate fernet keys by (in seconds). Must be an interval of
# 60(1 min), 120(2 min), 180(3 min), 240(4 min), 300(5 min), 360(6 min),
# 600(10 min), 720(12 min), 900(15 min), 1200(20 min), 1800(30 min),
# 3600(1 hour), 7200(2 hour), 10800(3 hour), 14400(4 hour), 21600(6 hour),
# 28800(8 hour), 43200(12 hour), 86400(1 day), 604800(1 week).
#fernet_token_expiry: 86400


#########################
# Glance - Image Options
#########################
# Configure image backend.
#glance_backend_file: "yes"
#glance_backend_ceph: "no"

#######################
# Ceilometer options
#######################
# Valid options are [ mongodb, mysql, gnocchi ]
#ceilometer_database_type: "mongodb"


#######################
# Gnocchi options
#######################
# Valid options are [ file, ceph ]
#gnocchi_backend_storage: "{{ 'ceph' if enable_ceph|bool else 'file' }}"


#################################
# Cinder - Block Storage Options
#################################
# Enable / disable Cinder backends
#cinder_backend_ceph: "{{ enable_ceph }}"

#cinder_volume_group: "cinder-volumes"


#########################
# Nova - Compute Options
#########################
#nova_backend_ceph: "{{ enable_ceph }}"


##############################
# Horizon - Dashboard Options
##############################
#horizon_backend_database: "no"


#######################################
# Manila - Shared File Systems Options
#######################################
# HNAS backend configuration
#hnas_ip:
#hnas_user:
#hnas_password:
#hnas_evs_id:
#hnas_evs_ip:
#hnas_file_system_name:

##################################
# Swift - Object Storage Options
##################################
# Swift expects block devices to be available for storage. Two types of storage
# are supported: 1 - storage device with a special partition name and filesystem
# label, 2 - unpartitioned disk  with a filesystem. The label of this filesystem
# is used to detect the disk which Swift will be using.

# Swift support two mathcing modes, valid options are [ prefix, strict ]
#swift_devices_match_mode: "strict"

# This parameter defines matching pattern: if "strict" mode was selected,
# for swift_devices_match_mode then swift_device_name should specify the name of
# the special swift partition for example: "KOLLA_SWIFT_DATA", if "prefix" mode was
# selected then swift_devices_name should specify a pattern which would match to
# filesystems' labels prepared for swift.
#swift_devices_name: "KOLLA_SWIFT_DATA"


################################################
# Tempest - The OpenStack Integration Test Suite
################################################
# following value must be set when enable tempest
tempest_image_id:
tempest_flavor_ref_id:
tempest_public_network_id:
tempest_floating_network_name:

# tempest_image_alt_id: "{{ tempest_image_id }}"
# tempest_flavor_ref_alt_id: "{{ tempest_flavor_ref_id }}"