# Copyright 2012 Cisco Systems, Inc.  All rights reserved.
#
#    Licensed under the Apache License, Version 2.0 (the "License"); you may
#    not use this file except in compliance with the License. You may obtain
#    a copy of the License at
#
#         http://www.apache.org/licenses/LICENSE-2.0
#
#    Unless required by applicable law or agreed to in writing, software
#    distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
#    WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
#    License for the specific language governing permissions and limitations
#    under the License.

from oslo_config import cfg

from neutron._i18n import _

DEFAULT_BRIDGE_MAPPINGS = []
DEFAULT_INTERFACE_MAPPINGS = []
DEFAULT_VXLAN_GROUP = '224.0.0.1'
DEFAULT_KERNEL_HZ_VALUE = 250  # [Hz]
DEFAULT_TC_TBF_LATENCY = 50  # [ms]

vxlan_opts = [
    cfg.BoolOpt('enable_vxlan', default=True,
                help=_("Enable VXLAN on the agent. Can be enabled when "
                       "agent is managed by ml2 plugin using linuxbridge "
                       "mechanism driver")),
    cfg.IntOpt('ttl',
               help=_("TTL for vxlan interface protocol packets.")),
    cfg.IntOpt('tos',
               deprecated_for_removal=True,
               help=_("TOS for vxlan interface protocol packets. This option "
                      "is deprecated in favor of the dscp option in the AGENT "
                      "section and will be removed in a future release. "
                      "To convert the TOS value to DSCP, divide by 4.")),
    cfg.StrOpt('vxlan_group', default=DEFAULT_VXLAN_GROUP,
               help=_("Multicast group(s) for vxlan interface. A range of "
                      "group addresses may be specified by using CIDR "
                      "notation. Specifying a range allows different VNIs to "
                      "use different group addresses, reducing or eliminating "
                      "spurious broadcast traffic to the tunnel endpoints. "
                      "To reserve a unique group for each possible "
                      "(24-bit) VNI, use a /8 such as 239.0.0.0/8. This "
                      "setting must be the same on all the agents.")),
    cfg.IPOpt('local_ip',
              help=_("IP address of local overlay (tunnel) network endpoint. "
                     "Use either an IPv4 or IPv6 address that resides on one "
                     "of the host network interfaces. The IP version of this "
                     "value must match the value of the 'overlay_ip_version' "
                     "option in the ML2 plug-in configuration file on the "
                     "neutron server node(s).")),
    cfg.PortOpt('udp_srcport_min', default=0,
                help=_("The minimum of the UDP source port range used for "
                       "VXLAN communication.")),
    cfg.PortOpt('udp_srcport_max', default=0,
                help=_("The maximum of the UDP source port range used for "
                       "VXLAN communication.")),
    cfg.PortOpt('udp_dstport',
                help=_("The UDP port used for VXLAN communication. By "
                       "default, the Linux kernel doesn't use the IANA "
                       "assigned standard value, so if you want to use it, "
                       "this option must be set to 4789. It is not set by "
                       "default because of backward compatibiltiy.")),
    cfg.BoolOpt('l2_population', default=False,
                help=_("Extension to use alongside ml2 plugin's l2population "
                       "mechanism driver. It enables the plugin to populate "
                       "VXLAN forwarding table.")),
    cfg.BoolOpt('arp_responder', default=False,
                help=_("Enable local ARP responder which provides local "
                       "responses instead of performing ARP broadcast into "
                       "the overlay. Enabling local ARP responder is not "
                       "fully compatible with the allowed-address-pairs "
                       "extension.")
                ),
    cfg.ListOpt('multicast_ranges',
                default=[],
                help=_("Optional comma-separated list of "
                       "<multicast address>:<vni_min>:<vni_max> triples "
                       "describing how to assign a multicast address to "
                       "VXLAN according to its VNI ID.")),
]

bridge_opts = [
    cfg.ListOpt('physical_interface_mappings',
                default=DEFAULT_INTERFACE_MAPPINGS,
                help=_("Comma-separated list of "
                       "<physical_network>:<physical_interface> tuples "
                       "mapping physical network names to the agent's "
                       "node-specific physical network interfaces to be used "
                       "for flat and VLAN networks. All physical networks "
                       "listed in network_vlan_ranges on the server should "
                       "have mappings to appropriate interfaces on each "
                       "agent.")),
    cfg.ListOpt('bridge_mappings',
                default=DEFAULT_BRIDGE_MAPPINGS,
                help=_("List of <physical_network>:<physical_bridge>")),
]

qos_options = [
    cfg.IntOpt('kernel_hz', default=DEFAULT_KERNEL_HZ_VALUE,
               help=_("Value of host kernel tick rate (hz) for calculating "
                      "minimum burst value in bandwidth limit rules for "
                      "a port with QoS. See kernel configuration file for "
                      "HZ value and tc-tbf manual for more information.")),
    cfg.IntOpt('tbf_latency', default=DEFAULT_TC_TBF_LATENCY,
               help=_("Value of latency (ms) for calculating size of queue "
                      "for a port with QoS. See tc-tbf manual for more "
                      "information."))
]


def register_linuxbridge_opts(cfg=cfg.CONF):
    cfg.register_opts(vxlan_opts, "VXLAN")
    cfg.register_opts(bridge_opts, "LINUX_BRIDGE")
    cfg.register_opts(qos_options, "QOS")