Heat templates for deploying OpenStack
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

127 lines
5.6 KiB

# List of networks, used for j2 templating of enabled networks
# Supported values:
# name: Name of the network (mandatory)
# name_lower: lowercase version of name used for filenames
# (optional, defaults to name.lower())
# enabled: Is the network enabled (optional, defaults to true)
# NOTE: False will use noop.yaml for unused legacy networks to support upgrades.
# vlan: vlan for the network (optional)
# vip: Enable creation of a virtual IP on this network
# ip_subnet: IP/CIDR, e.g. '' or '2001:db8:fd00:1000::/64'
# (optional, may use parameter defaults instead)
# allocation_pools: IP range list e.g. [{'start':'', 'end':''}]
# gateway_ip: gateway for the network (optional, may use parameter defaults)
# routes: Optional, list of networks that should be routed via network gateway.
# Example: [{'destination':'', 'nexthop':''}]
# A single /16 supernet route could be used for 255 smaller /24 subnets.
# ipv6_subnet: Optional, sets default IPv6 subnet if IPv4 is already defined.
# ipv6_allocation_pools: Set default IPv6 allocation pools if IPv4 allocation pools
# are already defined.
# gateway_ipv6: Set an IPv6 gateway if IPv4 gateway already defined.
# ipv6: If ip_subnet not defined, this specifies that the network is IPv6-only.
# NOTE: IP-related values set parameter defaults in templates, may be overridden,
# either by operators, or e.g in environments/network-isolation-v6.yaml where we
# set some default IPv6 addresses.
# compat_name: for existing stack you may need to override the default
# transformation for the resource's name.
# mtu: Set the maximum transmission unit (MTU) that is guaranteed to pass
# through the data path of the segments in the network.
# (optional, defaults to 1500)
# Example:
# - name Example
# vip: false
# ip_subnet: ''
# allocation_pools: [{'start': '', 'end': ''}]
# gateway_ip: ''
# To support backward compatibility, two versions of the network definitions
# will be created, network/<network>.yaml and network/<network>_v6.yaml. Only
# one of these files may be used in the deployment at a time, since the
# parameters used for configuration are the same in both files. In the
# future, this behavior may be changed to create only one file for custom
# networks. You may specify IPv6 addresses for ip_subnet, allocation_pools,
# and gateway_ip if no IPv4 addresses are used for a custom network, or set
# ipv6: true, and the network/<network>.yaml file will be configured as IPv6.
# For configuring both IPv4 and IPv6 on the same interface, use two separate
# networks, and then assign both IPs to the same interface in a custom NIC
# configuration templates.
# The ordering of the networks below will determine the order in which NICs
# are assigned in the network/config/multiple-nics templates, beginning with
# NIC2, Control Plane is always NIC1.
- name: Storage
vip: true
vlan: 30
name_lower: storage
ip_subnet: ''
allocation_pools: [{'start': '', 'end': ''}]
ipv6_subnet: 'fd00:fd00:fd00:3000::/64'
ipv6_allocation_pools: [{'start': 'fd00:fd00:fd00:3000::10', 'end': 'fd00:fd00:fd00:3000:ffff:ffff:ffff:fffe'}]
mtu: 1500
- name: StorageMgmt
name_lower: storage_mgmt
vip: true
vlan: 40
ip_subnet: ''
allocation_pools: [{'start': '', 'end': ''}]
ipv6_subnet: 'fd00:fd00:fd00:4000::/64'
ipv6_allocation_pools: [{'start': 'fd00:fd00:fd00:4000::10', 'end': 'fd00:fd00:fd00:4000:ffff:ffff:ffff:fffe'}]
mtu: 1500
- name: InternalApi
name_lower: internal_api
vip: true
vlan: 20
ip_subnet: ''
allocation_pools: [{'start': '', 'end': ''}]
ipv6_subnet: 'fd00:fd00:fd00:2000::/64'
ipv6_allocation_pools: [{'start': 'fd00:fd00:fd00:2000::10', 'end': 'fd00:fd00:fd00:2000:ffff:ffff:ffff:fffe'}]
mtu: 1500
- name: Tenant
vip: false # Tenant network does not use VIPs
name_lower: tenant
vlan: 50
ip_subnet: ''
allocation_pools: [{'start': '', 'end': ''}]
ipv6_subnet: 'fd00:fd00:fd00:5000::/64'
ipv6_allocation_pools: [{'start': 'fd00:fd00:fd00:5000::10', 'end': 'fd00:fd00:fd00:5000:ffff:ffff:ffff:fffe'}]
mtu: 1500
- name: External
vip: true
name_lower: external
vlan: 10
ip_subnet: ''
allocation_pools: [{'start': '', 'end': ''}]
gateway_ip: ''
ipv6_subnet: '2001:db8:fd00:1000::/64'
ipv6_allocation_pools: [{'start': '2001:db8:fd00:1000::10', 'end': '2001:db8:fd00:1000:ffff:ffff:ffff:fffe'}]
gateway_ipv6: '2001:db8:fd00:1000::1'
mtu: 1500
- name: Management
# Management network is enabled by default for backwards-compatibility, but
# is not included in any roles by default. Add to role definitions to use.
enabled: true
vip: false # Management network does not use VIPs
name_lower: management
vlan: 60
ip_subnet: ''
allocation_pools: [{'start': '', 'end': ''}]
gateway_ip: ''
gateway_ipv6: 'fd00:fd00:fd00:6000::1'
ipv6_subnet: 'fd00:fd00:fd00:6000::/64'
ipv6_allocation_pools: [{'start': 'fd00:fd00:fd00:6000::10', 'end': 'fd00:fd00:fd00:6000:ffff:ffff:ffff:fffe'}]
mtu: 1500
- name: StorageNFS
enabled: true
vip: true
name_lower: storage_nfs
vlan: 70
ip_subnet: ''
allocation_pools: [{'start': '', 'end': ''}]
ipv6_subnet: 'fd00:fd00:fd00:7000::/64'
ipv6_allocation_pools: [{'start': 'fd00:fd00:fd00:7000::10', 'end': 'fd00:fd00:fd00:7000:ffff:ffff:ffff:fffe'}]
mtu: 1500