Merge "Replicate Proxy updates in R4 install guides"
This commit is contained in:
Zuul
Gerrit Code Review
commit
1157f5702f
@ -38,8 +38,8 @@ The items labeled *a* and *b* in the figure indicate two configuration files:
|
||||
* {controller OAM gateway IP/floating IP/host IP}
|
||||
* {controller management floating IP/host IP}
|
||||
* {controller cluster gateway IP}
|
||||
* 10.96.0.1
|
||||
* 10.96.0.10
|
||||
* 10.96.0.1 {apiserver cluster IP for Kubernetes}
|
||||
* 10.96.0.10 {coredns cluster IP for Kubernetes}
|
||||
* `*.cluster.local`
|
||||
|
||||
* Configuration file *b* lists container runtime proxy variables
|
||||
|
||||
@ -116,11 +116,20 @@ Bootstrap system on controller-0
|
||||
admin_username: admin
|
||||
admin_password: <admin-password>
|
||||
ansible_become_pass: <sysadmin-password>
|
||||
|
||||
# Add these lines to configure Docker to use a proxy server
|
||||
# docker_http_proxy: http://my.proxy.com:1080
|
||||
# docker_https_proxy: https://my.proxy.com:1443
|
||||
# docker_no_proxy:
|
||||
# - 1.2.3.4
|
||||
|
||||
EOF
|
||||
|
||||
Refer to :doc:`/deploy_install_guides/r4_release/ansible_bootstrap_configs`
|
||||
for information on additional Ansible bootstrap configurations for advanced
|
||||
Ansible bootstrap scenarios.
|
||||
Ansible bootstrap scenarios, such as Docker proxies when deploying behind a
|
||||
firewall, etc. Refer to :doc:`/../../configuration/docker_proxy_config` for
|
||||
details about Docker proxy settings.
|
||||
|
||||
#. Run the Ansible bootstrap playbook:
|
||||
|
||||
@ -250,6 +259,18 @@ Configure controller-0
|
||||
system host-disk-list controller-0 | awk '/\/dev\/sdb/{print $2}' | xargs -i system host-stor-add controller-0 {}
|
||||
system host-stor-list controller-0
|
||||
|
||||
#. If required, and not already done as part of bootstrap, configure Docker to
|
||||
use a proxy server.
|
||||
|
||||
#. List Docker proxy parameters:
|
||||
|
||||
::
|
||||
|
||||
system service-parameter-list platform docker
|
||||
|
||||
#. Refer to :doc:`/../../configuration/docker_proxy_config` for
|
||||
details about Docker proxy settings.
|
||||
|
||||
*************************************
|
||||
OpenStack-specific host configuration
|
||||
*************************************
|
||||
|
||||
@ -131,11 +131,20 @@ Bootstrap system on controller-0
|
||||
admin_username: admin
|
||||
admin_password: <admin-password>
|
||||
ansible_become_pass: <sysadmin-password>
|
||||
|
||||
# Add these lines to configure Docker to use a proxy server
|
||||
# docker_http_proxy: http://my.proxy.com:1080
|
||||
# docker_https_proxy: https://my.proxy.com:1443
|
||||
# docker_no_proxy:
|
||||
# - 1.2.3.4
|
||||
|
||||
EOF
|
||||
|
||||
Refer to :doc:`/deploy_install_guides/r4_release/ansible_bootstrap_configs`
|
||||
for information on additional Ansible bootstrap configurations for advanced
|
||||
Ansible bootstrap scenarios.
|
||||
Ansible bootstrap scenarios, such as Docker proxies when deploying behind a
|
||||
firewall, etc. Refer to :doc:`/../../configuration/docker_proxy_config` for
|
||||
details about Docker proxy settings.
|
||||
|
||||
#. Run the Ansible bootstrap playbook:
|
||||
|
||||
@ -256,6 +265,18 @@ Configure controller-0
|
||||
system host-disk-list controller-0 | awk '/\/dev\/sdb/{print $2}' | xargs -i system host-stor-add controller-0 {}
|
||||
system host-stor-list controller-0
|
||||
|
||||
#. If required, and not already done as part of bootstrap, configure Docker to
|
||||
use a proxy server.
|
||||
|
||||
#. List Docker proxy parameters:
|
||||
|
||||
::
|
||||
|
||||
system service-parameter-list platform docker
|
||||
|
||||
#. Refer to :doc:`/../../configuration/docker_proxy_config` for
|
||||
details about Docker proxy settings.
|
||||
|
||||
*************************************
|
||||
OpenStack-specific host configuration
|
||||
*************************************
|
||||
|
||||
@ -137,11 +137,20 @@ Bootstrap system on controller-0
|
||||
admin_username: admin
|
||||
admin_password: <admin-password>
|
||||
ansible_become_pass: <sysadmin-password>
|
||||
|
||||
# Add these lines to configure Docker to use a proxy server
|
||||
# docker_http_proxy: http://my.proxy.com:1080
|
||||
# docker_https_proxy: https://my.proxy.com:1443
|
||||
# docker_no_proxy:
|
||||
# - 1.2.3.4
|
||||
|
||||
EOF
|
||||
|
||||
Refer to :doc:`/deploy_install_guides/r4_release/ansible_bootstrap_configs`
|
||||
for information on additional Ansible bootstrap configurations for advanced
|
||||
Ansible bootstrap scenarios.
|
||||
Ansible bootstrap scenarios, such as Docker proxies when deploying behind a
|
||||
firewall, etc. Refer to :doc:`/../../configuration/docker_proxy_config` for
|
||||
details about Docker proxy settings.
|
||||
|
||||
#. Run the Ansible bootstrap playbook:
|
||||
|
||||
@ -165,7 +174,7 @@ Configure controller-0
|
||||
|
||||
::
|
||||
|
||||
source /etc/platform/openrc
|
||||
source /etc/platform/openrc
|
||||
|
||||
#. Configure the OAM and MGMT interfaces of controller-0 and specify the
|
||||
attached networks. Use the OAM and MGMT port names, for example eth0, that are
|
||||
@ -173,24 +182,24 @@ Configure controller-0
|
||||
|
||||
::
|
||||
|
||||
OAM_IF=<OAM-PORT>
|
||||
MGMT_IF=<MGMT-PORT>
|
||||
system host-if-modify controller-0 lo -c none
|
||||
IFNET_UUIDS=$(system interface-network-list controller-0 | awk '{if ($6=="lo") print $4;}')
|
||||
for UUID in $IFNET_UUIDS; do
|
||||
system interface-network-remove ${UUID}
|
||||
done
|
||||
system host-if-modify controller-0 $OAM_IF -c platform
|
||||
system interface-network-assign controller-0 $OAM_IF oam
|
||||
system host-if-modify controller-0 $MGMT_IF -c platform
|
||||
system interface-network-assign controller-0 $MGMT_IF mgmt
|
||||
system interface-network-assign controller-0 $MGMT_IF cluster-host
|
||||
OAM_IF=<OAM-PORT>
|
||||
MGMT_IF=<MGMT-PORT>
|
||||
system host-if-modify controller-0 lo -c none
|
||||
IFNET_UUIDS=$(system interface-network-list controller-0 | awk '{if ($6=="lo") print $4;}')
|
||||
for UUID in $IFNET_UUIDS; do
|
||||
system interface-network-remove ${UUID}
|
||||
done
|
||||
system host-if-modify controller-0 $OAM_IF -c platform
|
||||
system interface-network-assign controller-0 $OAM_IF oam
|
||||
system host-if-modify controller-0 $MGMT_IF -c platform
|
||||
system interface-network-assign controller-0 $MGMT_IF mgmt
|
||||
system interface-network-assign controller-0 $MGMT_IF cluster-host
|
||||
|
||||
#. Configure NTP servers for network time synchronization:
|
||||
|
||||
::
|
||||
|
||||
system ntp-modify ntpservers=0.pool.ntp.org,1.pool.ntp.org
|
||||
system ntp-modify ntpservers=0.pool.ntp.org,1.pool.ntp.org
|
||||
|
||||
#. Configure Ceph storage backend
|
||||
|
||||
@ -206,6 +215,18 @@ Configure controller-0
|
||||
|
||||
system storage-backend-add ceph --confirmed
|
||||
|
||||
#. If required, and not already done as part of bootstrap, configure Docker to
|
||||
use a proxy server.
|
||||
|
||||
#. List Docker proxy parameters:
|
||||
|
||||
::
|
||||
|
||||
system service-parameter-list platform docker
|
||||
|
||||
#. Refer to :doc:`/../../configuration/docker_proxy_config` for
|
||||
details about Docker proxy settings.
|
||||
|
||||
*************************************
|
||||
OpenStack-specific host configuration
|
||||
*************************************
|
||||
@ -322,12 +343,12 @@ Install software on controller-1 and worker nodes
|
||||
::
|
||||
|
||||
system host-list
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
| id | hostname | personality | administrative | operational | availability |
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
| 1 | controller-0 | controller | unlocked | enabled | available |
|
||||
| 2 | None | None | locked | disabled | offline |
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
| id | hostname | personality | administrative | operational | availability |
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
| 1 | controller-0 | controller | unlocked | enabled | available |
|
||||
| 2 | None | None | locked | disabled | offline |
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
|
||||
#. Using the host id, set the personality of this host to 'controller':
|
||||
|
||||
@ -361,16 +382,16 @@ Install software on controller-1 and worker nodes
|
||||
|
||||
::
|
||||
|
||||
system host-list
|
||||
system host-list
|
||||
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
| id | hostname | personality | administrative | operational | availability |
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
| 1 | controller-0 | controller | unlocked | enabled | available |
|
||||
| 2 | controller-1 | controller | locked | disabled | online |
|
||||
| 3 | worker-0 | worker | locked | disabled | online |
|
||||
| 4 | worker-1 | worker | locked | disabled | online |
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
| id | hostname | personality | administrative | operational | availability |
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
| 1 | controller-0 | controller | unlocked | enabled | available |
|
||||
| 2 | controller-1 | controller | locked | disabled | online |
|
||||
| 3 | worker-0 | worker | locked | disabled | online |
|
||||
| 4 | worker-1 | worker | locked | disabled | online |
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
|
||||
----------------------
|
||||
Configure controller-1
|
||||
@ -387,11 +408,11 @@ install procedure.)
|
||||
|
||||
::
|
||||
|
||||
OAM_IF=<OAM-PORT>
|
||||
MGMT_IF=<MGMT-PORT>
|
||||
system host-if-modify controller-1 $OAM_IF -c platform
|
||||
system interface-network-assign controller-1 $OAM_IF oam
|
||||
system interface-network-assign controller-1 $MGMT_IF cluster-host
|
||||
OAM_IF=<OAM-PORT>
|
||||
MGMT_IF=<MGMT-PORT>
|
||||
system host-if-modify controller-1 $OAM_IF -c platform
|
||||
system interface-network-assign controller-1 $OAM_IF oam
|
||||
system interface-network-assign controller-1 $MGMT_IF cluster-host
|
||||
|
||||
*************************************
|
||||
OpenStack-specific host configuration
|
||||
@ -407,7 +428,7 @@ of installing the stx-openstack manifest and helm-charts later.
|
||||
|
||||
::
|
||||
|
||||
system host-label-assign controller-1 openstack-control-plane=enabled
|
||||
system host-label-assign controller-1 openstack-control-plane=enabled
|
||||
|
||||
.. incl-config-controller-1-end:
|
||||
|
||||
@ -421,7 +442,7 @@ Unlock controller-1 in order to bring it into service:
|
||||
|
||||
::
|
||||
|
||||
system host-unlock controller-1
|
||||
system host-unlock controller-1
|
||||
|
||||
Controller-1 will reboot in order to apply configuration changes and come into
|
||||
service. This can take 5-10 minutes, depending on the performance of the host
|
||||
@ -440,22 +461,22 @@ Configure worker nodes
|
||||
|
||||
::
|
||||
|
||||
system ceph-mon-add worker-0
|
||||
system ceph-mon-add worker-0
|
||||
|
||||
#. Wait for the worker node monitor to complete configuration:
|
||||
|
||||
::
|
||||
|
||||
system ceph-mon-list
|
||||
+--------------------------------------+-------+--------------+------------+------+
|
||||
| uuid | ceph_ | hostname | state | task |
|
||||
| | mon_g | | | |
|
||||
| | ib | | | |
|
||||
+--------------------------------------+-------+--------------+------------+------+
|
||||
| 64176b6c-e284-4485-bb2a-115dee215279 | 20 | controller-1 | configured | None |
|
||||
| a9ca151b-7f2c-4551-8167-035d49e2df8c | 20 | controller-0 | configured | None |
|
||||
| f76bc385-190c-4d9a-aa0f-107346a9907b | 20 | worker-0 | configured | None |
|
||||
+--------------------------------------+-------+--------------+------------+------+
|
||||
system ceph-mon-list
|
||||
+--------------------------------------+-------+--------------+------------+------+
|
||||
| uuid | ceph_ | hostname | state | task |
|
||||
| | mon_g | | | |
|
||||
| | ib | | | |
|
||||
+--------------------------------------+-------+--------------+------------+------+
|
||||
| 64176b6c-e284-4485-bb2a-115dee215279 | 20 | controller-1 | configured | None |
|
||||
| a9ca151b-7f2c-4551-8167-035d49e2df8c | 20 | controller-0 | configured | None |
|
||||
| f76bc385-190c-4d9a-aa0f-107346a9907b | 20 | worker-0 | configured | None |
|
||||
+--------------------------------------+-------+--------------+------------+------+
|
||||
|
||||
#. Assign the cluster-host network to the MGMT interface for the worker nodes:
|
||||
|
||||
@ -464,19 +485,19 @@ Configure worker nodes
|
||||
|
||||
::
|
||||
|
||||
for NODE in worker-0 worker-1; do
|
||||
system interface-network-assign $NODE mgmt0 cluster-host
|
||||
done
|
||||
for NODE in worker-0 worker-1; do
|
||||
system interface-network-assign $NODE mgmt0 cluster-host
|
||||
done
|
||||
|
||||
#. Configure data interfaces for worker nodes. Use the DATA port names, for
|
||||
example eth0, that are applicable to your deployment environment.
|
||||
|
||||
.. important::
|
||||
|
||||
This step is **required** for OpenStack.
|
||||
This step is **required** for OpenStack.
|
||||
|
||||
This step is optional for Kubernetes: Do this step if using SRIOV network
|
||||
attachments in hosted application containers.
|
||||
This step is optional for Kubernetes: Do this step if using SRIOV network
|
||||
attachments in hosted application containers.
|
||||
|
||||
For Kubernetes SRIOV network attachments:
|
||||
|
||||
@ -484,55 +505,55 @@ Configure worker nodes
|
||||
|
||||
::
|
||||
|
||||
for NODE in worker-0 worker-1; do
|
||||
system host-label-assign ${NODE} sriovdp=enabled
|
||||
done
|
||||
for NODE in worker-0 worker-1; do
|
||||
system host-label-assign ${NODE} sriovdp=enabled
|
||||
done
|
||||
|
||||
* If planning on running DPDK in containers on this host, configure the number
|
||||
of 1G Huge pages required on both NUMA nodes:
|
||||
|
||||
::
|
||||
|
||||
for NODE in worker-0 worker-1; do
|
||||
system host-memory-modify ${NODE} 0 -1G 100
|
||||
system host-memory-modify ${NODE} 1 -1G 100
|
||||
done
|
||||
for NODE in worker-0 worker-1; do
|
||||
system host-memory-modify ${NODE} 0 -1G 100
|
||||
system host-memory-modify ${NODE} 1 -1G 100
|
||||
done
|
||||
|
||||
For both Kubernetes and OpenStack:
|
||||
|
||||
::
|
||||
|
||||
DATA0IF=<DATA-0-PORT>
|
||||
DATA1IF=<DATA-1-PORT>
|
||||
PHYSNET0='physnet0'
|
||||
PHYSNET1='physnet1'
|
||||
SPL=/tmp/tmp-system-port-list
|
||||
SPIL=/tmp/tmp-system-host-if-list
|
||||
DATA0IF=<DATA-0-PORT>
|
||||
DATA1IF=<DATA-1-PORT>
|
||||
PHYSNET0='physnet0'
|
||||
PHYSNET1='physnet1'
|
||||
SPL=/tmp/tmp-system-port-list
|
||||
SPIL=/tmp/tmp-system-host-if-list
|
||||
|
||||
# configure the datanetworks in sysinv, prior to referencing it
|
||||
# in the ``system host-if-modify`` command'.
|
||||
system datanetwork-add ${PHYSNET0} vlan
|
||||
system datanetwork-add ${PHYSNET1} vlan
|
||||
# configure the datanetworks in sysinv, prior to referencing it
|
||||
# in the ``system host-if-modify`` command'.
|
||||
system datanetwork-add ${PHYSNET0} vlan
|
||||
system datanetwork-add ${PHYSNET1} vlan
|
||||
|
||||
for NODE in worker-0 worker-1; do
|
||||
echo "Configuring interface for: $NODE"
|
||||
set -ex
|
||||
system host-port-list ${NODE} --nowrap > ${SPL}
|
||||
system host-if-list -a ${NODE} --nowrap > ${SPIL}
|
||||
DATA0PCIADDR=$(cat $SPL | grep $DATA0IF |awk '{print $8}')
|
||||
DATA1PCIADDR=$(cat $SPL | grep $DATA1IF |awk '{print $8}')
|
||||
DATA0PORTUUID=$(cat $SPL | grep ${DATA0PCIADDR} | awk '{print $2}')
|
||||
DATA1PORTUUID=$(cat $SPL | grep ${DATA1PCIADDR} | awk '{print $2}')
|
||||
DATA0PORTNAME=$(cat $SPL | grep ${DATA0PCIADDR} | awk '{print $4}')
|
||||
DATA1PORTNAME=$(cat $SPL | grep ${DATA1PCIADDR} | awk '{print $4}')
|
||||
DATA0IFUUID=$(cat $SPIL | awk -v DATA0PORTNAME=$DATA0PORTNAME '($12 ~ DATA0PORTNAME) {print $2}')
|
||||
DATA1IFUUID=$(cat $SPIL | awk -v DATA1PORTNAME=$DATA1PORTNAME '($12 ~ DATA1PORTNAME) {print $2}')
|
||||
system host-if-modify -m 1500 -n data0 -c data ${NODE} ${DATA0IFUUID}
|
||||
system host-if-modify -m 1500 -n data1 -c data ${NODE} ${DATA1IFUUID}
|
||||
system interface-datanetwork-assign ${NODE} ${DATA0IFUUID} ${PHYSNET0}
|
||||
system interface-datanetwork-assign ${NODE} ${DATA1IFUUID} ${PHYSNET1}
|
||||
set +ex
|
||||
done
|
||||
for NODE in worker-0 worker-1; do
|
||||
echo "Configuring interface for: $NODE"
|
||||
set -ex
|
||||
system host-port-list ${NODE} --nowrap > ${SPL}
|
||||
system host-if-list -a ${NODE} --nowrap > ${SPIL}
|
||||
DATA0PCIADDR=$(cat $SPL | grep $DATA0IF |awk '{print $8}')
|
||||
DATA1PCIADDR=$(cat $SPL | grep $DATA1IF |awk '{print $8}')
|
||||
DATA0PORTUUID=$(cat $SPL | grep ${DATA0PCIADDR} | awk '{print $2}')
|
||||
DATA1PORTUUID=$(cat $SPL | grep ${DATA1PCIADDR} | awk '{print $2}')
|
||||
DATA0PORTNAME=$(cat $SPL | grep ${DATA0PCIADDR} | awk '{print $4}')
|
||||
DATA1PORTNAME=$(cat $SPL | grep ${DATA1PCIADDR} | awk '{print $4}')
|
||||
DATA0IFUUID=$(cat $SPIL | awk -v DATA0PORTNAME=$DATA0PORTNAME '($12 ~ DATA0PORTNAME) {print $2}')
|
||||
DATA1IFUUID=$(cat $SPIL | awk -v DATA1PORTNAME=$DATA1PORTNAME '($12 ~ DATA1PORTNAME) {print $2}')
|
||||
system host-if-modify -m 1500 -n data0 -c data ${NODE} ${DATA0IFUUID}
|
||||
system host-if-modify -m 1500 -n data1 -c data ${NODE} ${DATA1IFUUID}
|
||||
system interface-datanetwork-assign ${NODE} ${DATA0IFUUID} ${PHYSNET0}
|
||||
system interface-datanetwork-assign ${NODE} ${DATA1IFUUID} ${PHYSNET1}
|
||||
set +ex
|
||||
done
|
||||
|
||||
*************************************
|
||||
OpenStack-specific host configuration
|
||||
@ -548,27 +569,27 @@ OpenStack-specific host configuration
|
||||
|
||||
::
|
||||
|
||||
for NODE in worker-0 worker-1; do
|
||||
system host-label-assign $NODE openstack-compute-node=enabled
|
||||
system host-label-assign $NODE openvswitch=enabled
|
||||
system host-label-assign $NODE sriov=enabled
|
||||
done
|
||||
for NODE in worker-0 worker-1; do
|
||||
system host-label-assign $NODE openstack-compute-node=enabled
|
||||
system host-label-assign $NODE openvswitch=enabled
|
||||
system host-label-assign $NODE sriov=enabled
|
||||
done
|
||||
|
||||
#. **For OpenStack only:** Set up disk partition for nova-local volume group,
|
||||
which is needed for stx-openstack nova ephemeral disks.
|
||||
|
||||
::
|
||||
|
||||
for NODE in worker-0 worker-1; do
|
||||
echo "Configuring Nova local for: $NODE"
|
||||
ROOT_DISK=$(system host-show ${NODE} | grep rootfs | awk '{print $4}')
|
||||
ROOT_DISK_UUID=$(system host-disk-list ${NODE} --nowrap | grep ${ROOT_DISK} | awk '{print $2}')
|
||||
PARTITION_SIZE=10
|
||||
NOVA_PARTITION=$(system host-disk-partition-add -t lvm_phys_vol ${NODE} ${ROOT_DISK_UUID} ${PARTITION_SIZE})
|
||||
NOVA_PARTITION_UUID=$(echo ${NOVA_PARTITION} | grep -ow "| uuid | [a-z0-9\-]* |" | awk '{print $4}')
|
||||
system host-lvg-add ${NODE} nova-local
|
||||
system host-pv-add ${NODE} nova-local ${NOVA_PARTITION_UUID}
|
||||
done
|
||||
for NODE in worker-0 worker-1; do
|
||||
echo "Configuring Nova local for: $NODE"
|
||||
ROOT_DISK=$(system host-show ${NODE} | grep rootfs | awk '{print $4}')
|
||||
ROOT_DISK_UUID=$(system host-disk-list ${NODE} --nowrap | grep ${ROOT_DISK} | awk '{print $2}')
|
||||
PARTITION_SIZE=10
|
||||
NOVA_PARTITION=$(system host-disk-partition-add -t lvm_phys_vol ${NODE} ${ROOT_DISK_UUID} ${PARTITION_SIZE})
|
||||
NOVA_PARTITION_UUID=$(echo ${NOVA_PARTITION} | grep -ow "| uuid | [a-z0-9\-]* |" | awk '{print $4}')
|
||||
system host-lvg-add ${NODE} nova-local
|
||||
system host-pv-add ${NODE} nova-local ${NOVA_PARTITION_UUID}
|
||||
done
|
||||
|
||||
--------------------
|
||||
Unlock worker nodes
|
||||
@ -578,9 +599,9 @@ Unlock worker nodes in order to bring them into service:
|
||||
|
||||
::
|
||||
|
||||
for NODE in worker-0 worker-1; do
|
||||
system host-unlock $NODE
|
||||
done
|
||||
for NODE in worker-0 worker-1; do
|
||||
system host-unlock $NODE
|
||||
done
|
||||
|
||||
The worker nodes will reboot in order to apply configuration changes and come into
|
||||
service. This can take 5-10 minutes, depending on the performance of the host machine.
|
||||
@ -593,39 +614,39 @@ Add Ceph OSDs to controllers
|
||||
|
||||
.. important::
|
||||
|
||||
This step requires a configured Ceph storage backend
|
||||
This step requires a configured Ceph storage backend.
|
||||
|
||||
::
|
||||
|
||||
HOST=controller-0
|
||||
DISKS=$(system host-disk-list ${HOST})
|
||||
TIERS=$(system storage-tier-list ceph_cluster)
|
||||
OSDs="/dev/sdb"
|
||||
for OSD in $OSDs; do
|
||||
system host-stor-add ${HOST} $(echo "$DISKS" | grep "$OSD" | awk '{print $2}') --tier-uuid $(echo "$TIERS" | grep storage | awk '{print $2}')
|
||||
while true; do system host-stor-list ${HOST} | grep ${OSD} | grep configuring; if [ $? -ne 0 ]; then break; fi; sleep 1; done
|
||||
done
|
||||
HOST=controller-0
|
||||
DISKS=$(system host-disk-list ${HOST})
|
||||
TIERS=$(system storage-tier-list ceph_cluster)
|
||||
OSDs="/dev/sdb"
|
||||
for OSD in $OSDs; do
|
||||
system host-stor-add ${HOST} $(echo "$DISKS" | grep "$OSD" | awk '{print $2}') --tier-uuid $(echo "$TIERS" | grep storage | awk '{print $2}')
|
||||
while true; do system host-stor-list ${HOST} | grep ${OSD} | grep configuring; if [ $? -ne 0 ]; then break; fi; sleep 1; done
|
||||
done
|
||||
|
||||
system host-stor-list $HOST
|
||||
system host-stor-list $HOST
|
||||
|
||||
#. Add OSDs to controller-1. The following example adds OSDs to the `sdb` disk:
|
||||
|
||||
.. important::
|
||||
|
||||
This step requires a configured Ceph storage backend
|
||||
This step requires a configured Ceph storage backend.
|
||||
|
||||
::
|
||||
|
||||
HOST=controller-1
|
||||
DISKS=$(system host-disk-list ${HOST})
|
||||
TIERS=$(system storage-tier-list ceph_cluster)
|
||||
OSDs="/dev/sdb"
|
||||
for OSD in $OSDs; do
|
||||
system host-stor-add ${HOST} $(echo "$DISKS" | grep "$OSD" | awk '{print $2}') --tier-uuid $(echo "$TIERS" | grep storage | awk '{print $2}')
|
||||
while true; do system host-stor-list ${HOST} | grep ${OSD} | grep configuring; if [ $? -ne 0 ]; then break; fi; sleep 1; done
|
||||
done
|
||||
HOST=controller-1
|
||||
DISKS=$(system host-disk-list ${HOST})
|
||||
TIERS=$(system storage-tier-list ceph_cluster)
|
||||
OSDs="/dev/sdb"
|
||||
for OSD in $OSDs; do
|
||||
system host-stor-add ${HOST} $(echo "$DISKS" | grep "$OSD" | awk '{print $2}') --tier-uuid $(echo "$TIERS" | grep storage | awk '{print $2}')
|
||||
while true; do system host-stor-list ${HOST} | grep ${OSD} | grep configuring; if [ $? -ne 0 ]; then break; fi; sleep 1; done
|
||||
done
|
||||
|
||||
system host-stor-list $HOST
|
||||
system host-stor-list $HOST
|
||||
|
||||
----------
|
||||
Next steps
|
||||
|
||||
@ -45,11 +45,11 @@ Configure controller-0
|
||||
Unlock controller-0
|
||||
-------------------
|
||||
|
||||
.. important::
|
||||
.. important::
|
||||
|
||||
Make sure the Ceph storage backend is configured. If it is
|
||||
not configured, you will not be able to configure storage
|
||||
nodes.
|
||||
Make sure the Ceph storage backend is configured. If it is
|
||||
not configured, you will not be able to configure storage
|
||||
nodes.
|
||||
|
||||
Unlock controller-0 in order to bring it into service:
|
||||
|
||||
@ -75,13 +75,13 @@ Install software on controller-1, storage nodes, and worker nodes
|
||||
|
||||
::
|
||||
|
||||
system host-list
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
| id | hostname | personality | administrative | operational | availability |
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
| 1 | controller-0 | controller | unlocked | enabled | available |
|
||||
| 2 | None | None | locked | disabled | offline |
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
system host-list
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
| id | hostname | personality | administrative | operational | availability |
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
| 1 | controller-0 | controller | unlocked | enabled | available |
|
||||
| 2 | None | None | locked | disabled | offline |
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
|
||||
#. Using the host id, set the personality of this host to 'controller':
|
||||
|
||||
@ -101,14 +101,14 @@ Install software on controller-1, storage nodes, and worker nodes
|
||||
|
||||
::
|
||||
|
||||
system host-update 3 personality=storage
|
||||
system host-update 3 personality=storage
|
||||
|
||||
Repeat for storage-1. Power on storage-1 and wait for the new host
|
||||
(hostname=None) to be discovered by checking 'system host-list':
|
||||
|
||||
::
|
||||
|
||||
system host-update 4 personality=storage
|
||||
system host-update 4 personality=storage
|
||||
|
||||
This initiates the software installation on storage-0 and storage-1.
|
||||
This can take 5-10 minutes, depending on the performance of the host machine.
|
||||
@ -128,7 +128,7 @@ Install software on controller-1, storage nodes, and worker nodes
|
||||
|
||||
::
|
||||
|
||||
system host-update 6 personality=worker hostname=worker-1
|
||||
system host-update 6 personality=worker hostname=worker-1
|
||||
|
||||
This initiates the install of software on worker-0 and worker-1.
|
||||
|
||||
@ -138,17 +138,17 @@ Install software on controller-1, storage nodes, and worker nodes
|
||||
|
||||
::
|
||||
|
||||
system host-list
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
| id | hostname | personality | administrative | operational | availability |
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
| 1 | controller-0 | controller | unlocked | enabled | available |
|
||||
| 2 | controller-1 | controller | locked | disabled | online |
|
||||
| 3 | storage-0 | storage | locked | disabled | online |
|
||||
| 4 | storage-1 | storage | locked | disabled | online |
|
||||
| 5 | worker-0 | worker | locked | disabled | online |
|
||||
| 6 | worker-1 | worker | locked | disabled | online |
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
system host-list
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
| id | hostname | personality | administrative | operational | availability |
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
| 1 | controller-0 | controller | unlocked | enabled | available |
|
||||
| 2 | controller-1 | controller | locked | disabled | online |
|
||||
| 3 | storage-0 | storage | locked | disabled | online |
|
||||
| 4 | storage-1 | storage | locked | disabled | online |
|
||||
| 5 | worker-0 | worker | locked | disabled | online |
|
||||
| 6 | worker-1 | worker | locked | disabled | online |
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
|
||||
----------------------
|
||||
Configure controller-1
|
||||
@ -177,39 +177,39 @@ Configure storage nodes
|
||||
|
||||
::
|
||||
|
||||
for NODE in storage-0 storage-1; do
|
||||
system interface-network-assign $NODE mgmt0 cluster-host
|
||||
done
|
||||
for NODE in storage-0 storage-1; do
|
||||
system interface-network-assign $NODE mgmt0 cluster-host
|
||||
done
|
||||
|
||||
#. Add OSDs to storage-0. The following example adds OSDs to the `sdb` disk:
|
||||
|
||||
::
|
||||
|
||||
HOST=storage-0
|
||||
DISKS=$(system host-disk-list ${HOST})
|
||||
TIERS=$(system storage-tier-list ceph_cluster)
|
||||
OSDs="/dev/sdb"
|
||||
for OSD in $OSDs; do
|
||||
system host-stor-add ${HOST} $(echo "$DISKS" | grep "$OSD" | awk '{print $2}') --tier-uuid $(echo "$TIERS" | grep storage | awk '{print $2}')
|
||||
while true; do system host-stor-list ${HOST} | grep ${OSD} | grep configuring; if [ $? -ne 0 ]; then break; fi; sleep 1; done
|
||||
done
|
||||
HOST=storage-0
|
||||
DISKS=$(system host-disk-list ${HOST})
|
||||
TIERS=$(system storage-tier-list ceph_cluster)
|
||||
OSDs="/dev/sdb"
|
||||
for OSD in $OSDs; do
|
||||
system host-stor-add ${HOST} $(echo "$DISKS" | grep "$OSD" | awk '{print $2}') --tier-uuid $(echo "$TIERS" | grep storage | awk '{print $2}')
|
||||
while true; do system host-stor-list ${HOST} | grep ${OSD} | grep configuring; if [ $? -ne 0 ]; then break; fi; sleep 1; done
|
||||
done
|
||||
|
||||
system host-stor-list $HOST
|
||||
system host-stor-list $HOST
|
||||
|
||||
#. Add OSDs to storage-1. The following example adds OSDs to the `sdb` disk:
|
||||
|
||||
::
|
||||
|
||||
HOST=storage-1
|
||||
DISKS=$(system host-disk-list ${HOST})
|
||||
TIERS=$(system storage-tier-list ceph_cluster)
|
||||
OSDs="/dev/sdb"
|
||||
for OSD in $OSDs; do
|
||||
system host-stor-add ${HOST} $(echo "$DISKS" | grep "$OSD" | awk '{print $2}') --tier-uuid $(echo "$TIERS" | grep storage | awk '{print $2}')
|
||||
while true; do system host-stor-list ${HOST} | grep ${OSD} | grep configuring; if [ $? -ne 0 ]; then break; fi; sleep 1; done
|
||||
done
|
||||
HOST=storage-1
|
||||
DISKS=$(system host-disk-list ${HOST})
|
||||
TIERS=$(system storage-tier-list ceph_cluster)
|
||||
OSDs="/dev/sdb"
|
||||
for OSD in $OSDs; do
|
||||
system host-stor-add ${HOST} $(echo "$DISKS" | grep "$OSD" | awk '{print $2}') --tier-uuid $(echo "$TIERS" | grep storage | awk '{print $2}')
|
||||
while true; do system host-stor-list ${HOST} | grep ${OSD} | grep configuring; if [ $? -ne 0 ]; then break; fi; sleep 1; done
|
||||
done
|
||||
|
||||
system host-stor-list $HOST
|
||||
system host-stor-list $HOST
|
||||
|
||||
--------------------
|
||||
Unlock storage nodes
|
||||
@ -219,9 +219,9 @@ Unlock storage nodes in order to bring them into service:
|
||||
|
||||
::
|
||||
|
||||
for STORAGE in storage-0 storage-1; do
|
||||
system host-unlock $STORAGE
|
||||
done
|
||||
for STORAGE in storage-0 storage-1; do
|
||||
system host-unlock $STORAGE
|
||||
done
|
||||
|
||||
The storage nodes will reboot in order to apply configuration changes and come
|
||||
into service. This can take 5-10 minutes, depending on the performance of the
|
||||
@ -238,9 +238,9 @@ Configure worker nodes
|
||||
|
||||
::
|
||||
|
||||
for NODE in worker-0 worker-1; do
|
||||
system interface-network-assign $NODE mgmt0 cluster-host
|
||||
done
|
||||
for NODE in worker-0 worker-1; do
|
||||
system interface-network-assign $NODE mgmt0 cluster-host
|
||||
done
|
||||
|
||||
#. Configure data interfaces for worker nodes. Use the DATA port names, for
|
||||
example eth0, that are applicable to your deployment environment.
|
||||
@ -258,55 +258,55 @@ Configure worker nodes
|
||||
|
||||
::
|
||||
|
||||
for NODE in worker-0 worker-1; do
|
||||
system host-label-assign ${NODE} sriovdp=enabled
|
||||
done
|
||||
for NODE in worker-0 worker-1; do
|
||||
system host-label-assign ${NODE} sriovdp=enabled
|
||||
done
|
||||
|
||||
* If planning on running DPDK in containers on this host, configure the number
|
||||
of 1G Huge pages required on both NUMA nodes:
|
||||
|
||||
::
|
||||
|
||||
for NODE in worker-0 worker-1; do
|
||||
system host-memory-modify ${NODE} 0 -1G 100
|
||||
system host-memory-modify ${NODE} 1 -1G 100
|
||||
done
|
||||
for NODE in worker-0 worker-1; do
|
||||
system host-memory-modify ${NODE} 0 -1G 100
|
||||
system host-memory-modify ${NODE} 1 -1G 100
|
||||
done
|
||||
|
||||
For both Kubernetes and OpenStack:
|
||||
|
||||
::
|
||||
|
||||
DATA0IF=<DATA-0-PORT>
|
||||
DATA1IF=<DATA-1-PORT>
|
||||
PHYSNET0='physnet0'
|
||||
PHYSNET1='physnet1'
|
||||
SPL=/tmp/tmp-system-port-list
|
||||
SPIL=/tmp/tmp-system-host-if-list
|
||||
DATA0IF=<DATA-0-PORT>
|
||||
DATA1IF=<DATA-1-PORT>
|
||||
PHYSNET0='physnet0'
|
||||
PHYSNET1='physnet1'
|
||||
SPL=/tmp/tmp-system-port-list
|
||||
SPIL=/tmp/tmp-system-host-if-list
|
||||
|
||||
# configure the datanetworks in sysinv, prior to referencing it
|
||||
# in the ``system host-if-modify`` command'.
|
||||
system datanetwork-add ${PHYSNET0} vlan
|
||||
system datanetwork-add ${PHYSNET1} vlan
|
||||
# configure the datanetworks in sysinv, prior to referencing it
|
||||
# in the ``system host-if-modify`` command'.
|
||||
system datanetwork-add ${PHYSNET0} vlan
|
||||
system datanetwork-add ${PHYSNET1} vlan
|
||||
|
||||
for NODE in worker-0 worker-1; do
|
||||
echo "Configuring interface for: $NODE"
|
||||
set -ex
|
||||
system host-port-list ${NODE} --nowrap > ${SPL}
|
||||
system host-if-list -a ${NODE} --nowrap > ${SPIL}
|
||||
DATA0PCIADDR=$(cat $SPL | grep $DATA0IF |awk '{print $8}')
|
||||
DATA1PCIADDR=$(cat $SPL | grep $DATA1IF |awk '{print $8}')
|
||||
DATA0PORTUUID=$(cat $SPL | grep ${DATA0PCIADDR} | awk '{print $2}')
|
||||
DATA1PORTUUID=$(cat $SPL | grep ${DATA1PCIADDR} | awk '{print $2}')
|
||||
DATA0PORTNAME=$(cat $SPL | grep ${DATA0PCIADDR} | awk '{print $4}')
|
||||
DATA1PORTNAME=$(cat $SPL | grep ${DATA1PCIADDR} | awk '{print $4}')
|
||||
DATA0IFUUID=$(cat $SPIL | awk -v DATA0PORTNAME=$DATA0PORTNAME '($12 ~ DATA0PORTNAME) {print $2}')
|
||||
DATA1IFUUID=$(cat $SPIL | awk -v DATA1PORTNAME=$DATA1PORTNAME '($12 ~ DATA1PORTNAME) {print $2}')
|
||||
system host-if-modify -m 1500 -n data0 -c data ${NODE} ${DATA0IFUUID}
|
||||
system host-if-modify -m 1500 -n data1 -c data ${NODE} ${DATA1IFUUID}
|
||||
system interface-datanetwork-assign ${NODE} ${DATA0IFUUID} ${PHYSNET0}
|
||||
system interface-datanetwork-assign ${NODE} ${DATA1IFUUID} ${PHYSNET1}
|
||||
set +ex
|
||||
done
|
||||
for NODE in worker-0 worker-1; do
|
||||
echo "Configuring interface for: $NODE"
|
||||
set -ex
|
||||
system host-port-list ${NODE} --nowrap > ${SPL}
|
||||
system host-if-list -a ${NODE} --nowrap > ${SPIL}
|
||||
DATA0PCIADDR=$(cat $SPL | grep $DATA0IF |awk '{print $8}')
|
||||
DATA1PCIADDR=$(cat $SPL | grep $DATA1IF |awk '{print $8}')
|
||||
DATA0PORTUUID=$(cat $SPL | grep ${DATA0PCIADDR} | awk '{print $2}')
|
||||
DATA1PORTUUID=$(cat $SPL | grep ${DATA1PCIADDR} | awk '{print $2}')
|
||||
DATA0PORTNAME=$(cat $SPL | grep ${DATA0PCIADDR} | awk '{print $4}')
|
||||
DATA1PORTNAME=$(cat $SPL | grep ${DATA1PCIADDR} | awk '{print $4}')
|
||||
DATA0IFUUID=$(cat $SPIL | awk -v DATA0PORTNAME=$DATA0PORTNAME '($12 ~ DATA0PORTNAME) {print $2}')
|
||||
DATA1IFUUID=$(cat $SPIL | awk -v DATA1PORTNAME=$DATA1PORTNAME '($12 ~ DATA1PORTNAME) {print $2}')
|
||||
system host-if-modify -m 1500 -n data0 -c data ${NODE} ${DATA0IFUUID}
|
||||
system host-if-modify -m 1500 -n data1 -c data ${NODE} ${DATA1IFUUID}
|
||||
system interface-datanetwork-assign ${NODE} ${DATA0IFUUID} ${PHYSNET0}
|
||||
system interface-datanetwork-assign ${NODE} ${DATA1IFUUID} ${PHYSNET1}
|
||||
set +ex
|
||||
done
|
||||
|
||||
*************************************
|
||||
OpenStack-specific host configuration
|
||||
@ -322,27 +322,27 @@ OpenStack-specific host configuration
|
||||
|
||||
::
|
||||
|
||||
for NODE in worker-0 worker-1; do
|
||||
system host-label-assign $NODE openstack-compute-node=enabled
|
||||
system host-label-assign $NODE openvswitch=enabled
|
||||
system host-label-assign $NODE sriov=enabled
|
||||
done
|
||||
for NODE in worker-0 worker-1; do
|
||||
system host-label-assign $NODE openstack-compute-node=enabled
|
||||
system host-label-assign $NODE openvswitch=enabled
|
||||
system host-label-assign $NODE sriov=enabled
|
||||
done
|
||||
|
||||
#. **For OpenStack only:** Set up disk partition for nova-local volume group,
|
||||
which is needed for stx-openstack nova ephemeral disks.
|
||||
|
||||
::
|
||||
|
||||
for NODE in worker-0 worker-1; do
|
||||
echo "Configuring Nova local for: $NODE"
|
||||
ROOT_DISK=$(system host-show ${NODE} | grep rootfs | awk '{print $4}')
|
||||
ROOT_DISK_UUID=$(system host-disk-list ${NODE} --nowrap | grep ${ROOT_DISK} | awk '{print $2}')
|
||||
PARTITION_SIZE=10
|
||||
NOVA_PARTITION=$(system host-disk-partition-add -t lvm_phys_vol ${NODE} ${ROOT_DISK_UUID} ${PARTITION_SIZE})
|
||||
NOVA_PARTITION_UUID=$(echo ${NOVA_PARTITION} | grep -ow "| uuid | [a-z0-9\-]* |" | awk '{print $4}')
|
||||
system host-lvg-add ${NODE} nova-local
|
||||
system host-pv-add ${NODE} nova-local ${NOVA_PARTITION_UUID}
|
||||
done
|
||||
for NODE in worker-0 worker-1; do
|
||||
echo "Configuring Nova local for: $NODE"
|
||||
ROOT_DISK=$(system host-show ${NODE} | grep rootfs | awk '{print $4}')
|
||||
ROOT_DISK_UUID=$(system host-disk-list ${NODE} --nowrap | grep ${ROOT_DISK} | awk '{print $2}')
|
||||
PARTITION_SIZE=10
|
||||
NOVA_PARTITION=$(system host-disk-partition-add -t lvm_phys_vol ${NODE} ${ROOT_DISK_UUID} ${PARTITION_SIZE})
|
||||
NOVA_PARTITION_UUID=$(echo ${NOVA_PARTITION} | grep -ow "| uuid | [a-z0-9\-]* |" | awk '{print $4}')
|
||||
system host-lvg-add ${NODE} nova-local
|
||||
system host-pv-add ${NODE} nova-local ${NOVA_PARTITION_UUID}
|
||||
done
|
||||
|
||||
-------------------
|
||||
Unlock worker nodes
|
||||
@ -352,9 +352,9 @@ Unlock worker nodes in order to bring them into service:
|
||||
|
||||
::
|
||||
|
||||
for NODE in worker-0 worker-1; do
|
||||
system host-unlock $NODE
|
||||
done
|
||||
for NODE in worker-0 worker-1; do
|
||||
system host-unlock $NODE
|
||||
done
|
||||
|
||||
The worker nodes will reboot in order to apply configuration changes and come
|
||||
into service. This can take 5-10 minutes, depending on the performance of the
|
||||
|
||||
@ -14,8 +14,14 @@ End user applications can be deployed on bare metal servers (instead of
|
||||
virtual machines) by configuring OpenStack Ironic and deploying a pool of 1 or
|
||||
more bare metal servers.
|
||||
|
||||
.. note::
|
||||
|
||||
If you are behind a corporate firewall or proxy, you need to set proxy
|
||||
settings. Refer to :doc:`/../../configuration/docker_proxy_config` for
|
||||
details.
|
||||
|
||||
.. figure:: ../figures/starlingx-deployment-options-ironic.png
|
||||
:scale: 90%
|
||||
:scale: 50%
|
||||
:alt: Standard with Ironic deployment configuration
|
||||
|
||||
*Figure 1: Standard with Ironic deployment configuration*
|
||||
|
||||
@ -16,6 +16,12 @@ An AIO-DX configuration provides the following benefits:
|
||||
* All controller HA services go active on the remaining healthy server
|
||||
* All virtual machines are recovered on the remaining healthy server
|
||||
|
||||
.. note::
|
||||
|
||||
If you are behind a corporate firewall or proxy, you need to set proxy
|
||||
settings. Refer to :doc:`/../../configuration/docker_proxy_config` for
|
||||
details.
|
||||
|
||||
.. figure:: ../figures/starlingx-deployment-options-duplex.png
|
||||
:scale: 50%
|
||||
:alt: All-in-one Duplex deployment configuration
|
||||
|
||||
@ -7,6 +7,12 @@ following benefits:
|
||||
single pair of physical servers
|
||||
* A storage backend solution using a single-node CEPH deployment
|
||||
|
||||
.. note::
|
||||
|
||||
If you are behind a corporate firewall or proxy, you need to set proxy
|
||||
settings. Refer to :doc:`/../../configuration/docker_proxy_config` for
|
||||
details.
|
||||
|
||||
.. figure:: ../figures/starlingx-deployment-options-simplex.png
|
||||
:scale: 50%
|
||||
:alt: All-in-one Simplex deployment configuration
|
||||
|
||||
@ -15,6 +15,12 @@ A Standard with Controller Storage configuration provides the following benefits
|
||||
* On overall worker node failure, virtual machines and containers are
|
||||
recovered on the remaining healthy worker nodes
|
||||
|
||||
.. note::
|
||||
|
||||
If you are behind a corporate firewall or proxy, you need to set proxy
|
||||
settings. Refer to :doc:`/../../configuration/docker_proxy_config` for
|
||||
details.
|
||||
|
||||
.. figure:: ../figures/starlingx-deployment-options-controller-storage.png
|
||||
:scale: 50%
|
||||
:alt: Standard with Controller Storage deployment configuration
|
||||
|
||||
@ -8,7 +8,14 @@ A Standard with Dedicated Storage configuration provides the following benefits:
|
||||
across the controller nodes in either active/active or active/standby mode
|
||||
* A storage back end solution using a two-to-9x node HA CEPH storage cluster
|
||||
that supports a replication factor of two or three
|
||||
* Up to four groups of 2x storage nodes, or up to three groups of 3x storage nodes
|
||||
* Up to four groups of 2x storage nodes, or up to three groups of 3x storage
|
||||
nodes
|
||||
|
||||
.. note::
|
||||
|
||||
If you are behind a corporate firewall or proxy, you need to set proxy
|
||||
settings. Refer to :doc:`/../../configuration/docker_proxy_config` for
|
||||
details.
|
||||
|
||||
.. figure:: ../figures/starlingx-deployment-options-dedicated-storage.png
|
||||
:scale: 50%
|
||||
|
||||
Binary file not shown.
|
Before Width: | Height: | Size: 103 KiB After Width: | Height: | Size: 101 KiB |
@ -25,7 +25,7 @@ Install application manifest and helm-charts
|
||||
|
||||
::
|
||||
|
||||
system application-upload stx-openstack-<version>-centos-stable-latest.tgz
|
||||
system application-upload stx-openstack-<version>-centos-stable-latest.tgz
|
||||
|
||||
This will:
|
||||
|
||||
@ -36,11 +36,20 @@ Install application manifest and helm-charts
|
||||
recommended StarlingX configuration of OpenStack services.
|
||||
|
||||
#. Apply the stx-openstack application in order to bring StarlingX OpenStack into
|
||||
service.
|
||||
service. If your environment is preconfigured with a proxy server, then
|
||||
make sure HTTPS proxy is set before applying stx-openstack.
|
||||
|
||||
::
|
||||
|
||||
system application-apply stx-openstack
|
||||
system application-apply stx-openstack
|
||||
|
||||
.. note::
|
||||
|
||||
To set the HTTPS proxy at bootstrap time, refer to
|
||||
`Ansible Bootstrap Configurations <https://docs.starlingx.io/deploy_install_guides/r3_release/ansible_bootstrap_configs.html#docker-proxy>`_.
|
||||
|
||||
To set the HTTPS proxy after installation, refer to
|
||||
`Docker Proxy Configuration <https://docs.starlingx.io/configuration/docker_proxy_config.html>`_.
|
||||
|
||||
#. Wait for the activation of stx-openstack to complete.
|
||||
|
||||
@ -50,7 +59,7 @@ Install application manifest and helm-charts
|
||||
|
||||
::
|
||||
|
||||
watch -n 5 system application-list
|
||||
watch -n 5 system application-list
|
||||
|
||||
----------
|
||||
Next steps
|
||||
|
||||
@ -117,11 +117,20 @@ On virtual controller-0:
|
||||
admin_username: admin
|
||||
admin_password: <admin-password>
|
||||
ansible_become_pass: <sysadmin-password>
|
||||
|
||||
# Add these lines to configure Docker to use a proxy server
|
||||
# docker_http_proxy: http://my.proxy.com:1080
|
||||
# docker_https_proxy: https://my.proxy.com:1443
|
||||
# docker_no_proxy:
|
||||
# - 1.2.3.4
|
||||
|
||||
EOF
|
||||
|
||||
Refer to :doc:`/deploy_install_guides/r4_release/ansible_bootstrap_configs`
|
||||
for information on additional Ansible bootstrap configurations for advanced
|
||||
Ansible bootstrap scenarios.
|
||||
Ansible bootstrap scenarios, such as Docker proxies when deploying behind a
|
||||
firewall, etc. Refer to :doc:`/../../configuration/docker_proxy_config` for
|
||||
details about Docker proxy settings.
|
||||
|
||||
#. Run the Ansible bootstrap playbook:
|
||||
|
||||
@ -233,7 +242,7 @@ On virtual controller-0:
|
||||
|
||||
.. important::
|
||||
|
||||
This step requires a configured Ceph storage backend
|
||||
This step requires a configured Ceph storage backend.
|
||||
|
||||
::
|
||||
|
||||
@ -241,6 +250,19 @@ On virtual controller-0:
|
||||
system host-disk-list controller-0 | awk '/\/dev\/sdb/{print $2}' | xargs -i system host-stor-add controller-0 {}
|
||||
system host-stor-list controller-0
|
||||
|
||||
#. If required, and not already done as part of bootstrap, configure Docker to
|
||||
use a proxy server.
|
||||
|
||||
#. List Docker proxy parameters:
|
||||
|
||||
::
|
||||
|
||||
system service-parameter-list platform docker
|
||||
|
||||
#. Refer to :doc:`/../../configuration/docker_proxy_config` for
|
||||
details about Docker proxy settings.
|
||||
|
||||
|
||||
*************************************
|
||||
OpenStack-specific host configuration
|
||||
*************************************
|
||||
@ -313,7 +335,7 @@ Install software on controller-1 node
|
||||
| id | hostname | personality | administrative | operational | availability |
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
| 1 | controller-0 | controller | unlocked | enabled | available |
|
||||
| 2 | controller-1 | controller | locked | disabled | online |
|
||||
| 2 | controller-1 | controller | locked | disabled | online |
|
||||
+----+--------------+-------------+----------------+-------------+--------------+
|
||||
|
||||
----------------------
|
||||
|
||||
@ -116,11 +116,20 @@ On virtual controller-0:
|
||||
admin_username: admin
|
||||
admin_password: <admin-password>
|
||||
ansible_become_pass: <sysadmin-password>
|
||||
|
||||
# Add these lines to configure Docker to use a proxy server
|
||||
# docker_http_proxy: http://my.proxy.com:1080
|
||||
# docker_https_proxy: https://my.proxy.com:1443
|
||||
# docker_no_proxy:
|
||||
# - 1.2.3.4
|
||||
|
||||
EOF
|
||||
|
||||
Refer to :doc:`/deploy_install_guides/r4_release/ansible_bootstrap_configs`
|
||||
for information on additional Ansible bootstrap configurations for advanced
|
||||
Ansible bootstrap scenarios.
|
||||
Ansible bootstrap scenarios, such as Docker proxies when deploying behind a
|
||||
firewall, etc. Refer to :doc:`/../../configuration/docker_proxy_config` for
|
||||
details about Docker proxy settings.
|
||||
|
||||
#. Run the Ansible bootstrap playbook:
|
||||
|
||||
@ -232,6 +241,18 @@ On virtual controller-0:
|
||||
system host-disk-list controller-0 | awk '/\/dev\/sdb/{print $2}' | xargs -i system host-stor-add controller-0 {}
|
||||
system host-stor-list controller-0
|
||||
|
||||
#. If required, and not already done as part of bootstrap, configure Docker to
|
||||
use a proxy server.
|
||||
|
||||
#. List Docker proxy parameters:
|
||||
|
||||
::
|
||||
|
||||
system service-parameter-list platform docker
|
||||
|
||||
#. Refer to :doc:`/../../configuration/docker_proxy_config` for
|
||||
details about Docker proxy settings.
|
||||
|
||||
*************************************
|
||||
OpenStack-specific host configuration
|
||||
*************************************
|
||||
|
||||
@ -122,11 +122,20 @@ On virtual controller-0:
|
||||
admin_username: admin
|
||||
admin_password: <admin-password>
|
||||
ansible_become_pass: <sysadmin-password>
|
||||
|
||||
# Add these lines to configure Docker to use a proxy server
|
||||
# docker_http_proxy: http://my.proxy.com:1080
|
||||
# docker_https_proxy: https://my.proxy.com:1443
|
||||
# docker_no_proxy:
|
||||
# - 1.2.3.4
|
||||
|
||||
EOF
|
||||
|
||||
Refer to :doc:`/deploy_install_guides/r4_release/ansible_bootstrap_configs`
|
||||
for information on additional Ansible bootstrap configurations for advanced
|
||||
Ansible bootstrap scenarios.
|
||||
Ansible bootstrap scenarios, such as Docker proxies when deploying behind a
|
||||
firewall, etc. Refer to :doc:`/../../configuration/docker_proxy_config` for
|
||||
details about Docker proxy settings.
|
||||
|
||||
#. Run the Ansible bootstrap playbook:
|
||||
|
||||
@ -197,6 +206,18 @@ On virtual controller-0:
|
||||
|
||||
system storage-backend-add ceph --confirmed
|
||||
|
||||
#. If required, and not already done as part of bootstrap, configure Docker to
|
||||
use a proxy server.
|
||||
|
||||
#. List Docker proxy parameters:
|
||||
|
||||
::
|
||||
|
||||
system service-parameter-list platform docker
|
||||
|
||||
#. Refer to :doc:`/../../configuration/docker_proxy_config` for
|
||||
details about Docker proxy settings.
|
||||
|
||||
*************************************
|
||||
OpenStack-specific host configuration
|
||||
*************************************
|
||||
|
||||
@ -61,11 +61,11 @@ Configure controller-0
|
||||
Unlock controller-0
|
||||
-------------------
|
||||
|
||||
.. important::
|
||||
.. important::
|
||||
|
||||
Make sure the Ceph storage backend is configured. If it is
|
||||
not configured, you will not be able to configure storage
|
||||
nodes.
|
||||
Make sure the Ceph storage backend is configured. If it is
|
||||
not configured, you will not be able to configure storage
|
||||
nodes.
|
||||
|
||||
Unlock virtual controller-0 in order to bring it into service:
|
||||
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user