-- ================================================================== -- Copyright (C) 2002 by HUAWEI TECHNOLOGIES. All rights reserved. -- -- Description: HUAWEI Layer Two Interface Management MIB -- Reference: -- Version: V1.0 -- History: -- V1.0 -- ================================================================== HUAWEI-L2IF-MIB DEFINITIONS ::= BEGIN IMPORTS hwDatacomm FROM HUAWEI-MIB TruthValue,TEXTUAL-CONVENTION FROM SNMPv2-TC MODULE-IDENTITY, OBJECT-TYPE, Integer32, IpAddress, OBJECT-IDENTITY, NOTIFICATION-TYPE, Counter64 FROM SNMPv2-SMI ifIndex,InterfaceIndex,ifDescr FROM IF-MIB RowStatus FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF VlanIdOrNone, VlanId FROM Q-BRIDGE-MIB EnabledStatus FROM P-BRIDGE-MIB; hwL2Mgmt OBJECT IDENTIFIER ::= { hwDatacomm 42 } hwL2IfMib MODULE-IDENTITY LAST-UPDATED "200505100836Z" ORGANIZATION "Huawei Technologies co.,Ltd." CONTACT-INFO "VRP Team Huawei Technologies co.,Ltd. Huawei Bld.,NO.3 Xinxi Rd., Shang-Di Information Industry Base, Hai-Dian District Beijing P.R. China http://www.huawei.com Zip:100085 " DESCRIPTION "information of layer2 interface and information of hybrid port and information of trunk port" ::= { hwL2Mgmt 1 } VlanList ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Each octet within this value specifies a set of eight vlans, with the first octet specifying vlans 0 through 7, the second octet specifying vlans 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered vlan, and the least significant bit represents the highest numbered vlan. Thus, each vlan of the link is represented by a single bit within the value of this object. If that bit has a value of '1' then that vlan is included in the set of vlans; the vlan is not included if its bit has a value of '0'." SYNTAX OCTET STRING -- ============================================================================ hwL2IfObjects OBJECT IDENTIFIER ::= { hwL2IfMib 1 } hwL2Interface OBJECT IDENTIFIER ::= { hwL2IfObjects 1 } -- ============================================================================ -- -- ======================= definition begin =================================== -- -- ============================================================================ hwL2IfPortMax OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Max ports that this device supports,BRIDGE-MIB have a resemble definition." ::= { hwL2Interface 1 } hwL2TopologyDetect OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Whether to enable layer2 topology detection." ::= { hwL2Interface 2 } -- =========================================================================== -- layer 2 interface group -- =========================================================================== hwL2IfTable OBJECT-TYPE SYNTAX SEQUENCE OF HwL2IfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " This is a table of layer2 interface,so it displays some attribute of layer2 interface." ::= { hwL2Interface 3 } hwL2IfEntry OBJECT-TYPE SYNTAX HwL2IfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Entries of extended Huawei private interface information table " INDEX { hwL2IfPortNum } ::= { hwL2IfTable 1} HwL2IfEntry ::= SEQUENCE { hwL2IfPortNum Integer32, hwL2IfPortIfIndex InterfaceIndex, hwL2IfPortType INTEGER, hwL2IfPVID Integer32, hwL2IfIsSrcMacFilter TruthValue, hwL2IfMacAddrLearnMode INTEGER, hwL2IfMacAddressLearn INTEGER, hwL2IfBcastRatio Integer32, hwL2IfMcastRatio Integer32, hwL2IfUcastRatio Integer32, hwL2IfOutBcastRatio Integer32, hwL2IfOutMcastRatio Integer32, hwL2IfOutUcastRatio Integer32, hwL2IfDiscardBcast EnabledStatus, hwL2IfDiscardUnknownMcast EnabledStatus, hwL2IfDiscardUnknownUcast EnabledStatus, hwL2IfBpdu EnabledStatus, hwL2IfPortPriority Integer32, hwL2IfPortName OCTET STRING, hwL2IfInInvalidVlanPkts Counter64, hwL2IfFlushEnable EnabledStatus, hwL2IfFlushControlVlan Integer32, hwL2IfTrustDefaultPriority EnabledStatus, hwL2IfOfflineStatus EnabledStatus, hwL2IfQinqVlanTransEnable EnabledStatus, hwL2IfQinqVlanTransMissDrop INTEGER, hwL2IfIpSubnetVlanEnable EnabledStatus, hwL2IfMacVlanEnable EnabledStatus, hwL2IfPolicyVlanEnable EnabledStatus, hwL2IfVlanPrecedence Integer32, hwL2IfIsolateGroupEnable EnabledStatus } hwL2IfPortNum OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Number of layer2 interface port, a unique value, for each port.It is recommended that values are assigned contiguously starting from 1. " ::= { hwL2IfEntry 1 } hwL2IfPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "A unique value, greater than zero, for each interface or interface sub-layer in the managed system. The value is consistent with the ifIndex in ifTable of IF-MIB." ::= { hwL2IfEntry 2 } hwL2IfPortType OBJECT-TYPE SYNTAX INTEGER { invalid(0), trunk(1) , access(2) , hybrid(3) , fabric(4), qinq(5) } MAX-ACCESS read-write STATUS current DESCRIPTION " Layer2 interface Port type, it contains invalid(0), trunk(1), access(2), hybrid(3), fabric(4)and qinq(5).Do not support fabric(4) now.invalid(0),which we read only,can't modify." ::= { hwL2IfEntry 3 } hwL2IfPVID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION " Layer2 interface Port VLAN ID" ::= { hwL2IfEntry 4 } hwL2IfIsSrcMacFilter OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION " Whether to filter source MAC address. We don't support it now." ::= { hwL2IfEntry 5 } hwL2IfMacAddrLearnMode OBJECT-TYPE SYNTAX INTEGER { iVL(1), sVL(2) } MAX-ACCESS read-only STATUS current DESCRIPTION " Status indicates mac address learn mode of the interface. IVL(1) means independent VLAN learning.SVL means shared VLAN learning. We only support iVL now." ::= { hwL2IfEntry 6 } hwL2IfMacAddressLearn OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2), discard(3) } MAX-ACCESS read-write STATUS current DESCRIPTION " Status indicates if the interface is allowed to learn mac address, enable(1) can be setted, (enabled(1) means that the interface can learn mac address), otherwise disabled(2) can be setted. discard(3) means the interface will drop packets." ::= { hwL2IfEntry 7 } --suppression step of percentage mode hwL2IfBcastRatio OBJECT-TYPE SYNTAX Integer32 (0..100) MAX-ACCESS read-write STATUS current DESCRIPTION " Broadcast-suppression ratio. Default is 100% . 100% indicates that the broadcast isn't suppressed." ::= { hwL2IfEntry 8 } hwL2IfMcastRatio OBJECT-TYPE SYNTAX Integer32 (0..100) MAX-ACCESS read-write STATUS current DESCRIPTION " Multicast-suppression ratio.Default is 100%, 100% indicates that the multicast isn't suppressed." ::= { hwL2IfEntry 9 } hwL2IfUcastRatio OBJECT-TYPE SYNTAX Integer32 (0..100) MAX-ACCESS read-write STATUS current DESCRIPTION " Unicastsuppression ratio. Default is 100% , 100% indicates that the broadcast isn't suppressed." ::= { hwL2IfEntry 10 } hwL2IfOutBcastRatio OBJECT-TYPE SYNTAX Integer32 (0..100) MAX-ACCESS read-write STATUS current DESCRIPTION " Outbound broadcast-suppression ratio. Default is 100% . 100% indicates that the broadcast isn't suppressed." ::= { hwL2IfEntry 11 } hwL2IfOutMcastRatio OBJECT-TYPE SYNTAX Integer32 (0..100) MAX-ACCESS read-write STATUS current DESCRIPTION " Outbound multicast-suppression ratio.Default is 100%, 100% indicates that the multicast isn't suppressed." ::= { hwL2IfEntry 12 } hwL2IfOutUcastRatio OBJECT-TYPE SYNTAX Integer32 (0..100) MAX-ACCESS read-write STATUS current DESCRIPTION " Outbound unicastsuppression ratio. Default is 100% , 100% indicates that the broadcast isn't suppressed." ::= { hwL2IfEntry 13 } hwL2IfDiscardBcast OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION " The flag of droping the broadcast packets, 1:discard; 2:forward(default)." ::= { hwL2IfEntry 14 } hwL2IfDiscardUnknownMcast OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION " The flag of droping the unknown mutilcast packets, 1:discard; 2:forward(default)." ::= { hwL2IfEntry 15 } hwL2IfDiscardUnknownUcast OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION " The flag of droping the unknown unicast packets, 1:discard; 2:forward(default)." ::= { hwL2IfEntry 16 } hwL2IfBpdu OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Bpdu enable in port." ::= { hwL2IfEntry 17 } hwL2IfPortPriority OBJECT-TYPE SYNTAX Integer32 (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Port priority about interface." ::= { hwL2IfEntry 18 } hwL2IfPortName OBJECT-TYPE SYNTAX OCTET STRING(SIZE(0..48)) MAX-ACCESS read-only STATUS current DESCRIPTION "The interface name." ::= { hwL2IfEntry 19 } hwL2IfInInvalidVlanPkts OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION " The number of invalid VLAN packets." ::= { hwL2IfEntry 20 } hwL2IfFlushEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION " The flush enable status of layer2 port." ::= { hwL2IfEntry 21 } hwL2IfFlushControlVlan OBJECT-TYPE SYNTAX Integer32 (1..4094 | 65535) MAX-ACCESS read-write STATUS current DESCRIPTION " The control vlan of flush packet." ::= { hwL2IfEntry 22 } hwL2IfTrustDefaultPriority OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION " The flag of qinq port trust default priority, 1:enable; 2:disable(default)." ::= { hwL2IfEntry 23 } hwL2IfOfflineStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION " The flag of port offline status, 1:enable; 2:disable(default)." ::= { hwL2IfEntry 24 } hwL2IfQinqVlanTransEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enable QinQ VLAN translation, 1:enable; 2:disable(default)." ::= { hwL2IfEntry 25 } hwL2IfQinqVlanTransMissDrop OBJECT-TYPE SYNTAX INTEGER { noDrop(1), drop(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Packets are dropped when a VLAN translation miss occurs, 1:noDrop(default); 2:drop." ::= { hwL2IfEntry 26 } hwL2IfIpSubnetVlanEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enable VLAN assignment based on ip subnet, 1:enable(default); 2:disable." ::= { hwL2IfEntry 27 } hwL2IfMacVlanEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Mac Vlan enable, 1:enable; 2:disable(default)" ::= { hwL2IfEntry 28 } hwL2IfPolicyVlanEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Policy Vlan enable, 1:enable; 2:disable(default)" ::= { hwL2IfEntry 29 } hwL2IfVlanPrecedence OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Determine the priorities for selecting VLAN (MAC-based, subnet-based VLANs), 0:MAC VLAN(default); 1:IPSUBNET VLAN." ::= { hwL2IfEntry 30 } hwL2IfIsolateGroupEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The value enabled(1) indicates that the port is a member of the port-isolate group; disable(2) indicates that the port is not a member of the port-isolate group. The default value is disable(2)." DEFVAL {2} ::= { hwL2IfEntry 31 } -- ============================================================================ -- Hybrid port group -- ============================================================================ hwL2IfHybridPortTable OBJECT-TYPE SYNTAX SEQUENCE OF HwL2IfHybridPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Hybrid-port configuration table " ::= { hwL2Interface 9 } hwL2IfHybridPortEntry OBJECT-TYPE SYNTAX HwL2IfHybridPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Entry of Hybrid-port configuration table " INDEX { hwL2IfHybridPortIndex } ::= { hwL2IfHybridPortTable 1} HwL2IfHybridPortEntry ::= SEQUENCE { hwL2IfHybridPortIndex Integer32, hwL2IfHybridTaggedVlanListLow VlanList, hwL2IfHybridTaggedVlanListHigh VlanList, hwL2IfHybridUnTaggedVlanListLow VlanList, hwL2IfHybridUnTaggedVlanListHigh VlanList } hwL2IfHybridPortIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION " Index of Hybrid-port " ::= { hwL2IfHybridPortEntry 1 } hwL2IfHybridTaggedVlanListLow OBJECT-TYPE SYNTAX VlanList (SIZE(256)) MAX-ACCESS read-write STATUS current DESCRIPTION " The lowest possible value of the tagged vlan list on the Hybrid-port." ::= { hwL2IfHybridPortEntry 2 } hwL2IfHybridTaggedVlanListHigh OBJECT-TYPE SYNTAX VlanList (SIZE(256)) MAX-ACCESS read-write STATUS current DESCRIPTION " The highest possible value of the tagged vlan list on the Hybrid-port." ::= { hwL2IfHybridPortEntry 3 } hwL2IfHybridUnTaggedVlanListLow OBJECT-TYPE SYNTAX VlanList (SIZE(256)) MAX-ACCESS read-write STATUS current DESCRIPTION " The lowest possible value of the untagged vlan list on the Hybrid-port." ::= { hwL2IfHybridPortEntry 4 } hwL2IfHybridUnTaggedVlanListHigh OBJECT-TYPE SYNTAX VlanList (SIZE(256)) MAX-ACCESS read-write STATUS current DESCRIPTION " The highest possible value of the untagged vlan list on the Hybrid-port." ::= { hwL2IfHybridPortEntry 5 } -- ============================================================================ -- Trunk port group -- ============================================================================ hwL2IfTrunkPortTable OBJECT-TYPE SYNTAX SEQUENCE OF HwL2IfTrunkPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Trunk-port configuration table. Trunk-port is a logistic port." ::= { hwL2Interface 10 } hwL2IfTrunkPortEntry OBJECT-TYPE SYNTAX HwL2IfTrunkPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Entry of Trunk-port configuration table " INDEX { hwL2IfTrunkPortIndex } ::= { hwL2IfTrunkPortTable 1} HwL2IfTrunkPortEntry ::= SEQUENCE { hwL2IfTrunkPortIndex Integer32, hwL2IfTrunkAllowPassVlanListLow VlanList, hwL2IfTrunkAllowPassVlanListHigh VlanList } hwL2IfTrunkPortIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION " Index of Trunk-port " ::= { hwL2IfTrunkPortEntry 1 } hwL2IfTrunkAllowPassVlanListLow OBJECT-TYPE SYNTAX VlanList (SIZE(0..256)) MAX-ACCESS read-write STATUS current DESCRIPTION " The lowest possible value of the Vlan list that port Trunk allows to pass." ::= { hwL2IfTrunkPortEntry 2 } hwL2IfTrunkAllowPassVlanListHigh OBJECT-TYPE SYNTAX VlanList (SIZE(0..256)) MAX-ACCESS read-write STATUS current DESCRIPTION " The highest possible value of the Vlan list that port Trunk allows to pass." ::= { hwL2IfTrunkPortEntry 3 } hwL2IfPortIsolateTable OBJECT-TYPE SYNTAX SEQUENCE OF HwL2IfPortIsolateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Port isolate in the same Service-instance table. The Service-instance is used to communicate among different vlans." ::= { hwL2Interface 11 } hwL2IfPortIsolateEntry OBJECT-TYPE SYNTAX HwL2IfPortIsolateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Entry of port isolate configuration table." INDEX { hwL2IfPortIsolatePortIndex,hwL2IfPortIsolateSIName } ::= { hwL2IfPortIsolateTable 1} HwL2IfPortIsolateEntry ::= SEQUENCE { hwL2IfPortIsolatePortIndex Integer32, hwL2IfPortIsolateSIName OCTET STRING, hwL2IfPortIsolateRowStatus RowStatus } hwL2IfPortIsolatePortIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION " The port index of L2 interface." ::= { hwL2IfPortIsolateEntry 1 } hwL2IfPortIsolateSIName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION " The name of Service-instance.The Service-instance(S.I.)is used to communicate among different vlans." ::= { hwL2IfPortIsolateEntry 2 } hwL2IfPortIsolateRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION " The RowStatus of hwL2IfPortIsolateTable." ::= { hwL2IfPortIsolateEntry 3 } -- ============================================================================ -- hwL2IfSuppressionTable -- ============================================================================ hwL2IfSuppressionTable OBJECT-TYPE SYNTAX SEQUENCE OF HwL2IfSuppressionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Port suppression configuration table " ::= { hwL2Interface 12 } hwL2IfSuppressionEntry OBJECT-TYPE SYNTAX HwL2IfSuppressionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of port suppression configuration table " INDEX { hwL2IfSuppressionPortIndex ,hwL2IfSuppressionType } ::= { hwL2IfSuppressionTable 1} HwL2IfSuppressionEntry ::= SEQUENCE { hwL2IfSuppressionPortIndex Integer32, hwL2IfSuppressionType INTEGER, hwL2IfSuppressionCir Integer32, hwL2IfSuppressionCbs Integer32, hwL2IfSuppressionRowStatus RowStatus } hwL2IfSuppressionPortIndex OBJECT-TYPE SYNTAX Integer32 (1..512) MAX-ACCESS not-accessible STATUS current DESCRIPTION " The port index of L2 interface." ::= { hwL2IfSuppressionEntry 1 } hwL2IfSuppressionType OBJECT-TYPE SYNTAX INTEGER { broadcast(1), multicast(2), unicast(3) } MAX-ACCESS not-accessible STATUS current DESCRIPTION " Type of port suppression command, a unique value from 1 to 3: 1 means broadcast suppression; 2 means multicast suppression; 3 means unicast suppression." ::= { hwL2IfSuppressionEntry 2 } hwL2IfSuppressionCir OBJECT-TYPE SYNTAX Integer32 (0..10000000) MAX-ACCESS read-create STATUS current DESCRIPTION " Committed Information Rate. Unit: kbps." ::= { hwL2IfSuppressionEntry 3 } hwL2IfSuppressionCbs OBJECT-TYPE SYNTAX Integer32 (2048..64000000) MAX-ACCESS read-create STATUS current DESCRIPTION " Committed Burst Size. Unit: byte" ::= { hwL2IfSuppressionEntry 4 } hwL2IfSuppressionRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION " The RowStatus of hwL2IfSuppressionTable ." ::= { hwL2IfSuppressionEntry 5 } -- ============================================================================ -- hwL2IfVlanSuppressionTable -- ============================================================================ hwL2IfVlanSuppressionTable OBJECT-TYPE SYNTAX SEQUENCE OF HwL2IfVlanSuppressionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Port and Vlan suppression configuration table " ::= { hwL2Interface 13 } hwL2IfVlanSuppressionEntry OBJECT-TYPE SYNTAX HwL2IfVlanSuppressionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of port and Vlan suppression configuration table " INDEX { hwL2IfVlanSuppressionPortIndex ,hwL2IfVlanSuppressionStartVlan, hwL2IfVlanSuppressionEndVlan } ::= { hwL2IfVlanSuppressionTable 1} HwL2IfVlanSuppressionEntry ::= SEQUENCE { hwL2IfVlanSuppressionPortIndex Integer32, hwL2IfVlanSuppressionStartVlan Integer32, hwL2IfVlanSuppressionEndVlan Integer32, hwL2IfVlanSuppressionCir Integer32, hwL2IfVlanSuppressionCbs Integer32, hwL2IfVlanSuppressionRowStatus RowStatus } hwL2IfVlanSuppressionPortIndex OBJECT-TYPE SYNTAX Integer32 (1..512) MAX-ACCESS not-accessible STATUS current DESCRIPTION " The port index of L2 interface." ::= { hwL2IfVlanSuppressionEntry 1 } hwL2IfVlanSuppressionStartVlan OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS not-accessible STATUS current DESCRIPTION " The start vlan-id of port and vlan suppression." ::= { hwL2IfVlanSuppressionEntry 2 } hwL2IfVlanSuppressionEndVlan OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS not-accessible STATUS current DESCRIPTION " The end vlan-id of port and vlan suppression." ::= { hwL2IfVlanSuppressionEntry 3 } hwL2IfVlanSuppressionCir OBJECT-TYPE SYNTAX Integer32 (0..10000000) MAX-ACCESS read-create STATUS current DESCRIPTION " Committed Information Rate. Unit: kbps." ::= { hwL2IfVlanSuppressionEntry 4 } hwL2IfVlanSuppressionCbs OBJECT-TYPE SYNTAX Integer32 (2048..64000000) MAX-ACCESS read-create STATUS current DESCRIPTION " Committed Burst Size. Unit: byte" ::= { hwL2IfVlanSuppressionEntry 5 } hwL2IfVlanSuppressionRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION " The RowStatus of hwL2IfVlanSuppressionTable ." ::= { hwL2IfVlanSuppressionEntry 6 } hwL2IfPortTcnTable OBJECT-TYPE SYNTAX SEQUENCE OF HwL2IfPortTcnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Port TCN in the same Service-instance table. The Service-instance is used to configure TCN." ::= { hwL2Interface 14 } hwL2IfPortTcnEntry OBJECT-TYPE SYNTAX HwL2IfPortTcnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " Entry of port TCN configuration table." INDEX { hwL2IfTcnPortIndex } ::= { hwL2IfPortTcnTable 1} HwL2IfPortTcnEntry ::= SEQUENCE { hwL2IfTcnPortIndex Integer32, hwL2IfTcnStp EnabledStatus, hwL2IfTcnSmartLink EnabledStatus, hwL2IfTcnVlanListLow OCTET STRING, hwL2IfTcnVlanListHigh OCTET STRING } hwL2IfTcnPortIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION " The port index of L2 interface." ::= { hwL2IfPortTcnEntry 1 } hwL2IfTcnStp OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION " Status indicates if the interface is allowed to notify stp TCN message , enable(1) can be setted, (enabled(1) means that the interface can notify TCN), otherwise disabled(2) can be setted." ::= { hwL2IfPortTcnEntry 2 } hwL2IfTcnSmartLink OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION " Status indicates if the interface is allowed to notify SmartLink TCN message, enable(1) can be setted, (enabled(1) means that the interface can notify TCN), otherwise disabled(2) can be setted." ::= { hwL2IfPortTcnEntry 3 } hwL2IfTcnVlanListLow OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..31)) MAX-ACCESS read-write STATUS current DESCRIPTION "The lowest possible value of the vlan list on the Tcn-port." ::= { hwL2IfPortTcnEntry 4 } hwL2IfTcnVlanListHigh OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..31)) MAX-ACCESS read-write STATUS current DESCRIPTION " The highest possible value of the vlan list on the Tcn-port." ::= { hwL2IfPortTcnEntry 5 } hwL2IfPortLoopDetectTable OBJECT-TYPE SYNTAX SEQUENCE OF HwL2IfPortLoopDetectEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing the port external loopback detection information for device. It can protect the port from external loopback." ::= { hwL2Interface 15 } hwL2IfPortLoopDetectEntry OBJECT-TYPE SYNTAX HwL2IfPortLoopDetectEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entries of the port external loopback detection table." INDEX { hwL2IfPortLoopDetectPort } ::= { hwL2IfPortLoopDetectTable 1 } HwL2IfPortLoopDetectEntry ::= SEQUENCE { hwL2IfPortLoopDetectPort Integer32, hwL2IfPortLoopDetectEnabled EnabledStatus, hwL2IfPortLoopDetectInterval Integer32, hwL2IfPortLoopDetectAction INTEGER, hwL2IfPortLoopDetectStatus INTEGER, hwL2IfPortLoopDetectProtocol OCTET STRING } hwL2IfPortLoopDetectPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port number which will be configured port external loopback detection." ::= { hwL2IfPortLoopDetectEntry 1 } hwL2IfPortLoopDetectEnabled OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "When this object is set to 'enabled(1)' Port external loopback detection is enabled on this port else disabled." ::= { hwL2IfPortLoopDetectEntry 2 } hwL2IfPortLoopDetectInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The detect period of port external loopback detection." ::= { hwL2IfPortLoopDetectEntry 3 } hwL2IfPortLoopDetectAction OBJECT-TYPE SYNTAX INTEGER { shutdown(1), block(2), trap(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The port external loopback detection protect action of this entry." ::= { hwL2IfPortLoopDetectEntry 4 } hwL2IfPortLoopDetectStatus OBJECT-TYPE SYNTAX INTEGER { normal(1), block(2), shutdown(3), trap(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current status of port(block/shutdown/trap/normal)." ::= { hwL2IfPortLoopDetectEntry 5 } hwL2IfPortLoopDetectProtocol OBJECT-TYPE SYNTAX OCTET STRING (SIZE(2)) MAX-ACCESS read-write STATUS current DESCRIPTION "The ethernet type of the detecting packet to port external loopback detection." ::= { hwL2IfPortLoopDetectEntry 6 } hwL2IfPortProtocolVlanDataTable OBJECT-TYPE SYNTAX SEQUENCE OF HwL2IfPortProtocolVlanDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of protocol vlan by port." ::= { hwL2Interface 16 } hwL2IfPortProtocolVlanDataEntry OBJECT-TYPE SYNTAX HwL2IfPortProtocolVlanDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of protocol vlan by port." INDEX { hwL2IfPortProtocolVlanDataPortIndex } ::= { hwL2IfPortProtocolVlanDataTable 1 } HwL2IfPortProtocolVlanDataEntry ::= SEQUENCE { hwL2IfPortProtocolVlanDataPortIndex Integer32, hwL2IfPortProtocolVlanDataVlan Integer32, hwL2IfPortProtocolVlanDataPri Integer32, hwL2IfPortProtocolVlanDataRowStatus RowStatus } hwL2IfPortProtocolVlanDataPortIndex OBJECT-TYPE SYNTAX Integer32 (1..479) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The protocol vlan Index of port ." ::= { hwL2IfPortProtocolVlanDataEntry 1 } hwL2IfPortProtocolVlanDataVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "VLAN ID." ::= { hwL2IfPortProtocolVlanDataEntry 2 } hwL2IfPortProtocolVlanDataPri OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "VLAN PRI." ::= { hwL2IfPortProtocolVlanDataEntry 3 } hwL2IfPortProtocolVlanDataRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Operation status." ::= { hwL2IfPortProtocolVlanDataEntry 4 } -- ============================================================================ -- hwL2IfPwSuppressionTable -- ============================================================================ hwL2IfPwSuppressionTable OBJECT-TYPE SYNTAX SEQUENCE OF HwL2IfPwSuppressionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Pw suppression configuration table " ::= { hwL2Interface 17 } hwL2IfPwSuppressionEntry OBJECT-TYPE SYNTAX HwL2IfPwSuppressionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the configuration table for PW-based unknown traffic suppression." INDEX { hwL2IfPwSuppressionVsiName,hwL2IfPwSuppressionPwName,hwL2IfPwSuppressionType } ::= { hwL2IfPwSuppressionTable 1} HwL2IfPwSuppressionEntry ::= SEQUENCE { hwL2IfPwSuppressionVsiName OCTET STRING, hwL2IfPwSuppressionPwName OCTET STRING, hwL2IfPwSuppressionType INTEGER, hwL2IfPwSuppressionCir Integer32, hwL2IfPwSuppressionCbs Integer32, hwL2IfPwSuppressionRowStatus RowStatus } hwL2IfPwSuppressionVsiName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the name of the VSI that is configured with PW-based unknown traffic suppression." ::= { hwL2IfPwSuppressionEntry 1 } hwL2IfPwSuppressionPwName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..16)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the name of the PW that is configured with PW-based unknown traffic suppression." ::= { hwL2IfPwSuppressionEntry 2 } hwL2IfPwSuppressionType OBJECT-TYPE SYNTAX INTEGER { broadcast(1), multicast(2), unicast(3) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of this object identifies the type of PW-based unknown traffic suppression: 1: broadcast suppression 2: multicast suppression 3: unknown unicast suppression" ::= { hwL2IfPwSuppressionEntry 3 } hwL2IfPwSuppressionCir OBJECT-TYPE SYNTAX Integer32 (100..1000000) MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the Committed Information Rate. Unit: kbit/s." ::= { hwL2IfPwSuppressionEntry 4 } hwL2IfPwSuppressionCbs OBJECT-TYPE SYNTAX Integer32 (100..33554432) MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the Committed Burst Size. Unit: byte." ::= { hwL2IfPwSuppressionEntry 5 } hwL2IfPwSuppressionRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the RowStatus of hwPwSuppressionTable." ::= { hwL2IfPwSuppressionEntry 50 } -- ============================================================================ -- hwL2IfLoopDetectInterval -- ============================================================================ hwL2IfLoopDetectInterval OBJECT-TYPE SYNTAX Integer32 (5..300) MAX-ACCESS read-write STATUS current DESCRIPTION "The detect period of system external loopback detection." ::= { hwL2Interface 18 } -- ============================================================================ -- real-time relationship of port-vlan -- ============================================================================ hwL2IfDynamicPortVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF HwL2IfDynamicPortVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for dynamic relationship of port-vlan." ::= { hwL2Interface 19 } hwL2IfDynamicPortVlanEntry OBJECT-TYPE SYNTAX HwL2IfDynamicPortVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of dynamic port-vlan relationship table." INDEX { hwL2IfDynamicPortVlanPortIndex,hwL2IfDynamicPortVlanServiceType } ::= { hwL2IfDynamicPortVlanTable 1} HwL2IfDynamicPortVlanEntry ::= SEQUENCE { hwL2IfDynamicPortVlanPortIndex Integer32, hwL2IfDynamicPortVlanServiceType INTEGER, hwL2IfDynamicPortVlanPvid VlanIdOrNone, hwL2IfDynamicPortVlanUntaggedVlanListLow VlanList, hwL2IfDynamicPortVlanUntaggedVlanListHigh VlanList, hwL2IfDynamicPortVlanTaggedVlanListLow VlanList, hwL2IfDynamicPortVlanTaggedVlanListHigh VlanList } hwL2IfDynamicPortVlanPortIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Port index of switch-port." ::= { hwL2IfDynamicPortVlanEntry 1 } hwL2IfDynamicPortVlanServiceType OBJECT-TYPE SYNTAX INTEGER { configured(1), gvrp(2), voiceVLAN(3), unAuthenUserVLAN(4), dynAuthenVLAN(5), hvrp(6), elmi(7) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Service type of dynamic port-vlan relationship table." ::= { hwL2IfDynamicPortVlanEntry 2 } hwL2IfDynamicPortVlanPvid OBJECT-TYPE SYNTAX VlanIdOrNone MAX-ACCESS read-only STATUS current DESCRIPTION "The Dynamic PVID of port-vlan table." ::= { hwL2IfDynamicPortVlanEntry 3 } hwL2IfDynamicPortVlanUntaggedVlanListLow OBJECT-TYPE SYNTAX VlanList (SIZE(256)) MAX-ACCESS read-only STATUS current DESCRIPTION "The lowest possible value of the untagged vlan list of dynamic port-vlan table." ::= { hwL2IfDynamicPortVlanEntry 4 } hwL2IfDynamicPortVlanUntaggedVlanListHigh OBJECT-TYPE SYNTAX VlanList (SIZE(256)) MAX-ACCESS read-only STATUS current DESCRIPTION "The highest possible value of the untagged vlan list of Dynamic port-vlan table." ::= { hwL2IfDynamicPortVlanEntry 5 } hwL2IfDynamicPortVlanTaggedVlanListLow OBJECT-TYPE SYNTAX VlanList (SIZE(256)) MAX-ACCESS read-only STATUS current DESCRIPTION "The lowest possible value of the tagged vlan list of Dynamic port-vlan table." ::= { hwL2IfDynamicPortVlanEntry 6 } hwL2IfDynamicPortVlanTaggedVlanListHigh OBJECT-TYPE SYNTAX VlanList (SIZE(256)) MAX-ACCESS read-only STATUS current DESCRIPTION "The highest possible value of the tagged vlan list of Dynamic port-vlan table." ::= { hwL2IfDynamicPortVlanEntry 7 } hwL2IfTraps OBJECT IDENTIFIER ::= { hwL2IfObjects 2 } hwL2IfInvalidVlanPacketAlarm NOTIFICATION-TYPE OBJECTS {hwL2IfPortName,hwL2IfInInvalidVlanPkts} STATUS current DESCRIPTION "Warning of receiving invalid VLAN packets in the interface." ::= { hwL2IfTraps 1 } hwLoopDetectStatusAlarm NOTIFICATION-TYPE OBJECTS {ifDescr,hwL2IfPortLoopDetectStatus} STATUS current DESCRIPTION "Port status changed because loopback detect.(Normal/Block/Shutdown/Trap)" ::= { hwL2IfTraps 2 } hwL2IfConformance OBJECT IDENTIFIER ::= { hwL2IfMib 2 } hwL2IfCompliances OBJECT IDENTIFIER ::= { hwL2IfConformance 1 } hwL2IfMacAddrGroup OBJECT-GROUP OBJECTS{ hwL2IfMacAddrLearnMode , hwL2IfMacAddressLearn } STATUS current DESCRIPTION "A collection of objects indicate mac address learn of the interface." ::= { hwL2IfGroups 1 } hwL2IfBroadcastRatioGroup OBJECT-GROUP OBJECTS { hwL2IfBcastRatio, hwL2IfMcastRatio, hwL2IfUcastRatio, hwL2IfOutBcastRatio , hwL2IfOutMcastRatio , hwL2IfOutUcastRatio } STATUS current DESCRIPTION "A collection of objects indicate broadcast-suppression ratio." ::= { hwL2IfGroups 2 } hwL2IfHybridTaggedVlanGroup OBJECT-GROUP OBJECTS { hwL2IfHybridTaggedVlanListLow , hwL2IfHybridTaggedVlanListHigh , hwL2IfHybridUnTaggedVlanListLow , hwL2IfHybridUnTaggedVlanListHigh } STATUS current DESCRIPTION "A collection of objects indicate lowest/highest possible value of the tagged/untagged vlan list on the Hybrid-port." ::= { hwL2IfGroups 3 } hwL2IfTrunkAllowPassVlanListGroup OBJECT-GROUP OBJECTS { hwL2IfTrunkAllowPassVlanListLow , hwL2IfTrunkAllowPassVlanListHigh } STATUS current DESCRIPTION "A collection of objects indicate lowest/highed possible value of the allowed and passed vlan list on the Trunk-port." ::= { hwL2IfGroups 4 } hwL2IfPortGroup OBJECT-GROUP OBJECTS { hwL2IfPortIfIndex, hwL2IfIsSrcMacFilter } STATUS current DESCRIPTION "A collection of objects indicate index of layer2 port." ::= { hwL2IfGroups 5 } hwL2IfPVIDGroup OBJECT-GROUP OBJECTS { hwL2IfPVID } STATUS current DESCRIPTION "A collection of objects indicate PVID of layer2 interface." ::= { hwL2IfGroups 6 } hwL2IfPortTypeGroup OBJECT-GROUP OBJECTS { hwL2IfPortType } STATUS current DESCRIPTION "A collection of objects indicate VLAN type of layer2 interface." ::= { hwL2IfGroups 7 } hwL2IfPortMaxGroup OBJECT-GROUP OBJECTS { hwL2IfPortMax, hwL2TopologyDetect } STATUS current DESCRIPTION "A collection of objects indicate that the device supports maxmum of port ." ::= { hwL2IfGroups 8 } hwL2IfPortExtGroup OBJECT-GROUP OBJECTS { hwL2IfBpdu, hwL2IfDiscardBcast, hwL2IfDiscardUnknownMcast, hwL2IfDiscardUnknownUcast, hwL2IfPortPriority, hwL2IfPortName, hwL2IfInInvalidVlanPkts, hwL2IfFlushEnable, hwL2IfFlushControlVlan, hwL2IfTrustDefaultPriority, hwL2IfOfflineStatus, hwL2IfQinqVlanTransEnable, hwL2IfQinqVlanTransMissDrop, hwL2IfIpSubnetVlanEnable, hwL2IfMacVlanEnable, hwL2IfPolicyVlanEnable, hwL2IfVlanPrecedence, hwL2IfIsolateGroupEnable } STATUS current DESCRIPTION "A collection of objects indicate that the device supports attribute of port ." ::= { hwL2IfGroups 9 } hwL2IfPortIsolateGroup OBJECT-GROUP OBJECTS { hwL2IfPortIsolateRowStatus } STATUS current DESCRIPTION "A collection of objects indicate that the device supports islation of port ." ::= { hwL2IfGroups 10 } hwL2IfAlarmGroup NOTIFICATION-GROUP NOTIFICATIONS { hwL2IfInvalidVlanPacketAlarm, hwLoopDetectStatusAlarm } STATUS current DESCRIPTION "A collection of objects indicate that the device supports alarm of port ." ::= { hwL2IfGroups 11 } hwL2IfSuppressionGroup OBJECT-GROUP OBJECTS { hwL2IfSuppressionCir, hwL2IfSuppressionCbs, hwL2IfSuppressionRowStatus } STATUS current DESCRIPTION "A collection of objects that L2IfSuppression." ::= { hwL2IfGroups 12 } hwL2IfVlanSuppressionGroup OBJECT-GROUP OBJECTS { hwL2IfVlanSuppressionCir, hwL2IfVlanSuppressionCbs, hwL2IfVlanSuppressionRowStatus } STATUS current DESCRIPTION "A collection of values indicate that 'Committed infomation rate'." ::= { hwL2IfGroups 13 } hwL2IfPortTcnGroup OBJECT-GROUP OBJECTS { hwL2IfTcnStp, hwL2IfTcnSmartLink, hwL2IfTcnVlanListLow, hwL2IfTcnVlanListHigh } STATUS current DESCRIPTION "A collection of objects indicate that the device supports islation of port ." ::= { hwL2IfGroups 14 } hwL2IfPortLoopDetectGroup OBJECT-GROUP OBJECTS { hwL2IfPortLoopDetectEnabled, hwL2IfPortLoopDetectInterval, hwL2IfPortLoopDetectAction, hwL2IfPortLoopDetectStatus, hwL2IfPortLoopDetectProtocol, hwL2IfLoopDetectInterval } STATUS current DESCRIPTION "A collection of objects indicate that the port external loopback detection." ::= { hwL2IfGroups 15 } hwL2IfPortProtocolVlanDataGroup OBJECT-GROUP OBJECTS { hwL2IfPortProtocolVlanDataVlan, hwL2IfPortProtocolVlanDataPri, hwL2IfPortProtocolVlanDataRowStatus } STATUS current DESCRIPTION "The entry of protocol vlan by port." ::= { hwL2IfGroups 16 } hwL2IfPwSuppressionGroup OBJECT-GROUP OBJECTS { hwL2IfPwSuppressionCir, hwL2IfPwSuppressionCbs, hwL2IfPwSuppressionRowStatus } STATUS current DESCRIPTION "A collection of objects in L2IfPwSuppression." ::= { hwL2IfGroups 17 } hwL2IfDynamicPortVlanTableGroup OBJECT-GROUP OBJECTS { hwL2IfDynamicPortVlanPvid, hwL2IfDynamicPortVlanUntaggedVlanListLow, hwL2IfDynamicPortVlanUntaggedVlanListHigh, hwL2IfDynamicPortVlanTaggedVlanListLow, hwL2IfDynamicPortVlanTaggedVlanListHigh } STATUS current DESCRIPTION "A collection of objects of dynamic relationship of port-vlan." ::= { hwL2IfGroups 19 } -- ---------------------------------------------------------------------------- -- compliance statements -- ---------------------------------------------------------------------------- hwL2IfCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities implementing the Huawei layer two interface management MIB" MODULE MANDATORY-GROUPS { hwL2IfMacAddrGroup } GROUP hwL2IfBroadcastRatioGroup DESCRIPTION "This group supports in every device." GROUP hwL2IfHybridTaggedVlanGroup DESCRIPTION "This group supports in every device." GROUP hwL2IfTrunkAllowPassVlanListGroup DESCRIPTION "This group supports in every device." GROUP hwL2IfPortGroup DESCRIPTION "This group supports in every device." GROUP hwL2IfPVIDGroup DESCRIPTION "This group supports in every device." GROUP hwL2IfPortTypeGroup DESCRIPTION "This group supports in every device." GROUP hwL2IfPortMaxGroup DESCRIPTION "This group supports in every device." GROUP hwL2IfPortExtGroup DESCRIPTION "This group supports in every device." ::= { hwL2IfCompliances 1 } hwL2IfGroups OBJECT IDENTIFIER ::= { hwL2IfConformance 2 } END