-- =========================================================================== -- Description: MSDP MIB -- Reference: Module(MSDP-MIB) Extracted from RFC4624.TXT,from 4813 to 49606. -- =========================================================================== MSDP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, experimental, Counter32, Gauge32, TimeTicks, Integer32, IpAddress FROM SNMPv2-SMI RowStatus, TruthValue, TimeStamp, DisplayString FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF; msdpMIB MODULE-IDENTITY LAST-UPDATED "200608010000Z" ORGANIZATION "IETF MBONED Working Group" CONTACT-INFO "Bill Fenner 75 Willow Road Menlo Park, CA 94025 Phone: +1 650 867 6073 E-mail: fenner@research.att.com Dave Thaler One Microsoft Way Redmond, WA 98052 Phone: +1 425 703 8835 Email: dthaler@microsoft.com MBONED Working Group: mboned@lists.uoregon.edu" DESCRIPTION "An experimental MIB module for MSDP Management and Monitoring. Copyright (C) The Internet Society 2006. This version of this MIB module is part of RFC 4624; see the RFC itself for full legal notices." REVISION "200608010000Z" DESCRIPTION "Initial version, published as RFC 4624." ::= { experimental 92 } msdpMIBobjects OBJECT IDENTIFIER ::= { msdpMIB 1 } msdp OBJECT IDENTIFIER ::= { msdpMIBobjects 1 } msdpEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The state of MSDP on this MSDP speaker - globally enabled or disabled. Changes to this object should be stored to non-volatile memory." ::= { msdp 1 } msdpCacheLifetime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-write STATUS current DESCRIPTION "The lifetime given to SA cache entries when created or refreshed. This is the [SG-State-Period] in the MSDP spec. A value of 0 means no SA caching is done by this MSDP speaker. Changes to this object should be stored to non-volatile memory. This object does not measure time per se; instead, it is the delta from the time at which an SA message is received at which it should be expired if not refreshed. (i.e., it is the value of msdpSACacheExpiryTime immediately after receiving an SA message applying to that row.) As such, TimeInterval would be a more appropriate SYNTAX; it remains TimeTicks for backwards compatibility." REFERENCE "RFC 3618 section 5.3" ::= { msdp 2 } msdpNumSACacheEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of entries in the SA Cache table." ::= { msdp 3 } -- -- The spec doesn't define SA-Hold-Down-Period any more. -- msdpSAHoldDownPeriod OBJECT-TYPE -- ::= { msdp 9 } -- This object was introduced in error, with a similar definition -- to msdpCacheLifetime. -- msdpSAStatePeriod OBJECT-TYPE -- ::= { msdp 10 } msdpRPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The Rendezvous Point (RP) address used when sourcing MSDP SA messages. May be 0.0.0.0 on non-RPs. Changes to this object should be stored to non-volatile memory." ::= { msdp 11 } -- -- The MSDP Requests table -- SA Requests were removed from the MSDP spec, so this entire table -- is deprecated. msdpRequestsTable OBJECT-TYPE SYNTAX SEQUENCE OF MsdpRequestsEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The (conceptual) table listing group ranges and MSDP peers used when deciding where to send an SA Request message, when required. If SA Requests are not enabled, this table may be empty. In order to choose a peer to whom to send an SA Request for a given group, G, the subset of entries in this table whose (msdpRequestsPeerType, msdpRequestsPeer) tuple represents a peer whose msdpPeerState is established are examined. The set is further reduced by examining only those entries for which msdpPeerRequestsGroupAddressType equals the address type of G. The entries with the highest value of msdpRequestsGroupPrefix are considered, where the group G falls within the range described by the combination of msdpRequestsGroup and msdpRequestsGroupPrefix. (This sequence is commonly known as a 'longest-match' lookup.) Finally, if multiple entries remain, the entry with the lowest value of msdpRequestsPriority is chosen. The SA Request message is sent to the peer described by this row." ::= { msdp 4 } msdpRequestsEntry OBJECT-TYPE SYNTAX MsdpRequestsEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "An entry (conceptual row) representing a group range used when deciding where to send an SA Request message." INDEX { msdpRequestsGroupAddress, msdpRequestsGroupMask } ::= { msdpRequestsTable 1 } MsdpRequestsEntry ::= SEQUENCE { msdpRequestsGroupAddress IpAddress, msdpRequestsGroupMask IpAddress, msdpRequestsPeer IpAddress, msdpRequestsStatus RowStatus } msdpRequestsGroupAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The group address that, when combined with the mask in this entry, represents the group range to which this row applies." ::= { msdpRequestsEntry 1 } msdpRequestsGroupMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The mask that, when combined with the group address in this entry, represents the group range to which this row applies." ::= { msdpRequestsEntry 2 } msdpRequestsPeer OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The peer to which MSDP SA Requests for groups matching this entry's group range will be sent. This object, combined with msdpRequestsPeerType, must match the INDEX of a row in the msdpPeerTable, and to be considered, this peer's msdpPeerState must be established." ::= { msdpRequestsEntry 3 } msdpRequestsStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The status of this row, by which new rows may be added to the table or old rows may be deleted." ::= { msdpRequestsEntry 4 } -- -- The MSDP Peer table -- msdpPeerTable OBJECT-TYPE SYNTAX SEQUENCE OF MsdpPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the MSDP speaker's peers." ::= { msdp 5 } msdpPeerEntry OBJECT-TYPE SYNTAX MsdpPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing an MSDP peer. If row creation is supported, dynamically added rows are added to the system's stable configuration (corresponding to a StorageType value of nonVolatile). " INDEX { msdpPeerRemoteAddress } ::= { msdpPeerTable 1 } MsdpPeerEntry ::= SEQUENCE { msdpPeerRemoteAddress IpAddress, msdpPeerState INTEGER, msdpPeerRPFFailures Counter32, msdpPeerInSAs Counter32, msdpPeerOutSAs Counter32, msdpPeerInSARequests Counter32, msdpPeerOutSARequests Counter32, msdpPeerInSAResponses Counter32, msdpPeerOutSAResponses Counter32, msdpPeerInControlMessages Counter32, msdpPeerOutControlMessages Counter32, msdpPeerInDataPackets Counter32, msdpPeerOutDataPackets Counter32, msdpPeerFsmEstablishedTransitions Counter32, msdpPeerFsmEstablishedTime TimeStamp, msdpPeerInMessageTime TimeStamp, msdpPeerLocalAddress IpAddress, msdpPeerConnectRetryInterval Integer32, msdpPeerHoldTimeConfigured Integer32, msdpPeerKeepAliveConfigured Integer32, msdpPeerDataTtl Integer32, msdpPeerProcessRequestsFrom TruthValue, msdpPeerStatus RowStatus, msdpPeerRemotePort Integer32, msdpPeerLocalPort Integer32, msdpPeerEncapsulationType INTEGER, msdpPeerConnectionAttempts Counter32, msdpPeerInNotifications Counter32, msdpPeerOutNotifications Counter32, msdpPeerLastError OCTET STRING, msdpPeerDiscontinuityTime TimeStamp } msdpPeerRemoteAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The address of the remote MSDP peer." ::= { msdpPeerEntry 1 } -- dunno what happened to 2. msdpPeerState OBJECT-TYPE SYNTAX INTEGER { inactive(1), listen(2), connecting(3), established(4), disabled(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the MSDP TCP connection with this peer." ::= { msdpPeerEntry 3 } msdpPeerRPFFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of SA messages received from this peer that failed the Peer-RPF check. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 4 } msdpPeerInSAs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MSDP SA messages received on this connection. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 5 } msdpPeerOutSAs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MSDP SA messages transmitted on this connection. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 6 } msdpPeerInSARequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MSDP SA-Request messages received on this connection. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 7 } msdpPeerOutSARequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MSDP SA-Request messages transmitted on this connection. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 8 } msdpPeerInSAResponses OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of MSDP SA-Response messages received on this connection. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 9 } msdpPeerOutSAResponses OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of MSDP SA Response messages transmitted on this TCP connection. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 10 } msdpPeerInControlMessages OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MSDP messages, excluding encapsulated data packets, received on this TCP connection. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 11 } msdpPeerOutControlMessages OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MSDP messages, excluding encapsulated data packets, transmitted on this TCP connection. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 12 } msdpPeerInDataPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of encapsulated data packets received from this peer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 13 } msdpPeerOutDataPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of encapsulated data packets sent to this peer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of msdpPeerDiscontinuityTime." ::= { msdpPeerEntry 14 } msdpPeerFsmEstablishedTransitions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times the MSDP FSM transitioned into the ESTABLISHED state." REFERENCE "RFC 3618 section 11" ::= { msdpPeerEntry 15 } msdpPeerFsmEstablishedTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This timestamp is set to the value of sysUpTime when a peer transitions into or out of the ESTABLISHED state. It is set to zero when the MSDP speaker is booted." REFERENCE "RFC 3618 section 11" ::= { msdpPeerEntry 16 } msdpPeerInMessageTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The sysUpTime value when the last MSDP message was received from the peer. It is set to zero when the MSDP speaker is booted." ::= { msdpPeerEntry 17 } msdpPeerLocalAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The local IP address used for this entry's MSDP TCP connection." ::= { msdpPeerEntry 18 } -- msdpPeerSAAdvPeriod ([SA-Advertisement-Timer]) has been removed. -- ::= { msdpPeerEntry 19 } -- RFC 3618, Section 5.1, says it MUST be 60 seconds. msdpPeerConnectRetryInterval OBJECT-TYPE SYNTAX Integer32 (1..65535) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Time interval, in seconds, for the [ConnectRetry-period] for this peer." REFERENCE "RFC 3618 section 5.6" DEFVAL { 30 } ::= { msdpPeerEntry 20 } msdpPeerHoldTimeConfigured OBJECT-TYPE SYNTAX Integer32 (0|3..65535) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Time interval, in seconds, for the [HoldTime-Period] configured for this MSDP speaker with this peer. If the value of this object is zero (0), the MSDP connection is never torn down due to the absence of messages from the peer." REFERENCE "RFC 3618 section 5.4" DEFVAL { 75 } ::= { msdpPeerEntry 21 } msdpPeerKeepAliveConfigured OBJECT-TYPE SYNTAX Integer32 (0|1..21845) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Time interval, in seconds, for the [KeepAlive-Period] configured for this MSDP speaker with this peer. If the value of this object is zero (0), no periodic KEEPALIVE messages are sent to the peer after the MSDP connection has been established." REFERENCE "RFC 3618 section 5.5" DEFVAL { 60 } ::= { msdpPeerEntry 22 } msdpPeerDataTtl OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The minimum TTL a packet is required to have before it may be forwarded using SA encapsulation to this peer." DEFVAL { 1 } ::= { msdpPeerEntry 23 } msdpPeerProcessRequestsFrom OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This object indicates whether to process MSDP SA Request messages from this peer. If True(1), MSDP SA Request messages from this peer are processed and replied to (if appropriate) with SA Response messages. If False(2), MSDP SA Request messages from this peer are silently ignored. It defaults to False when msdpCacheLifetime is 0 and to True when msdpCacheLifetime is non-0. This object is deprecated because MSDP SA Requests were removed from the MSDP specification." ::= { msdpPeerEntry 24 } msdpPeerStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The RowStatus object by which peers can be added and deleted. A transition to 'active' will cause the MSDP 'Enable MSDP peering with P' Event to be generated. A transition out of the 'active' state will cause the MSDP 'Disable MSDP peering with P' Event to be generated. Care should be used in providing write access to this object without adequate authentication. msdpPeerRemoteAddress is the only variable that must be set to a valid value before the row can be activated. Since this is the table's INDEX, a row can be activated by simply setting the msdpPeerStatus variable. It is possible to modify other columns in the same conceptual row when the status value is active(1)." REFERENCE "RFC 3618 section 11.1" ::= { msdpPeerEntry 25 } msdpPeerRemotePort OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The remote port for the TCP connection between the MSDP peers." DEFVAL { 639 } ::= { msdpPeerEntry 26 } msdpPeerLocalPort OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The local port for the TCP connection between the MSDP peers." DEFVAL { 639 } ::= { msdpPeerEntry 27 } -- msdpPeerEncapsulationState has been removed -- because there is no longer an encapsulation -- state machine. -- ::= { msdpPeerEntry 28 } msdpPeerEncapsulationType OBJECT-TYPE SYNTAX INTEGER { none(0), tcp(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "The encapsulation in use when encapsulating data in SA messages to this peer." ::= { msdpPeerEntry 29 } msdpPeerConnectionAttempts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the state machine has transitioned from INACTIVE to CONNECTING." ::= { msdpPeerEntry 30 } msdpPeerInNotifications OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of MSDP Notification messages received from this peer. This object is deprecated because MSDP Notifications have been removed from the spec." ::= { msdpPeerEntry 31 } msdpPeerOutNotifications OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of MSDP Notification messages transmitted to this peer. This object is deprecated because MSDP Notifications have been removed from the spec." ::= { msdpPeerEntry 32 } msdpPeerLastError OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The last error code and subcode received via Notification from this peer. If no error has occurred, this field is zero. Otherwise, the first byte of this two-byte OCTET STRING contains the O-bit and error code, and the second byte contains the subcode. This object is deprecated because MSDP Notifications have been removed from the spec." DEFVAL { '0000'h } ::= { msdpPeerEntry 33 } msdpPeerDiscontinuityTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime on the most recent occasion at which one or more of this entry's counters suffered a discontinuity. See the DESCRIPTION of each object to see if it is expected to have discontinuities. These discontinuities may occur at peer connection establishment. If no such discontinuities have occurred since the last reinitialization of the local management subsystem, then this object contains a zero value." ::= { msdpPeerEntry 34 } -- -- The MSDP Source-Active Cache table -- msdpSACacheTable OBJECT-TYPE SYNTAX SEQUENCE OF MsdpSACacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the MSDP SA advertisements currently in the MSDP speaker's cache." ::= { msdp 6 } msdpSACacheEntry OBJECT-TYPE SYNTAX MsdpSACacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing an MSDP SA advertisement. The INDEX to this table includes msdpSACacheOriginRP for diagnosing incorrect MSDP advertisements; normally, a Group and Source pair would be unique. Row creation is not permitted; msdpSACacheStatus may only be used to delete rows from this table." INDEX { msdpSACacheGroupAddr, msdpSACacheSourceAddr, msdpSACacheOriginRP } ::= { msdpSACacheTable 1 } MsdpSACacheEntry ::= SEQUENCE { msdpSACacheGroupAddr IpAddress, msdpSACacheSourceAddr IpAddress, msdpSACacheOriginRP IpAddress, msdpSACachePeerLearnedFrom IpAddress, msdpSACacheRPFPeer IpAddress, msdpSACacheInSAs Counter32, msdpSACacheInDataPackets Counter32, msdpSACacheUpTime TimeTicks, msdpSACacheExpiryTime TimeTicks, msdpSACacheStatus RowStatus } msdpSACacheGroupAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The group address of the SA Cache entry." ::= { msdpSACacheEntry 1 } msdpSACacheSourceAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The source address of the SA Cache entry." ::= { msdpSACacheEntry 2 } msdpSACacheOriginRP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RP of the SA Cache entry. This field is in the INDEX in order to catch multiple RP's advertising the same source and group." ::= { msdpSACacheEntry 3 } msdpSACachePeerLearnedFrom OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The peer from which this SA Cache entry was last accepted. This address must correspond to the msdpPeerRemoteAddress value for a row in the MSDP Peer Table. This should be 0.0.0.0 on the router that originated the entry." ::= { msdpSACacheEntry 4 } msdpSACacheRPFPeer OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The peer from which an SA message corresponding to this cache entry would be accepted (i.e., the RPF peer for msdpSACacheOriginRP). This may be different than msdpSACachePeerLearnedFrom if this entry was created by an MSDP SA-Response. This address must correspond to the msdpPeerRemoteAddress value for a row in the MSDP Peer Table, or it may be 0.0.0.0 if no RPF peer exists." ::= { msdpSACacheEntry 5 } msdpSACacheInSAs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MSDP SA messages received relevant to this cache entry. This object must be initialized to zero when creating a cache entry." ::= { msdpSACacheEntry 6 } msdpSACacheInDataPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of MSDP-encapsulated data packets received relevant to this cache entry. This object must be initialized to zero when creating a cache entry." ::= { msdpSACacheEntry 7 } msdpSACacheUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time since this entry was first placed in the SA cache. The first epoch is the time that the entry was first placed in the SA cache, and the second epoch is the current time." ::= { msdpSACacheEntry 8 } msdpSACacheExpiryTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time remaining before this entry will expire from the SA cache. The first epoch is now, and the second epoch is the time that the entry will expire." ::= { msdpSACacheEntry 9 } msdpSACacheStatus OBJECT-TYPE SYNTAX RowStatus { active(1), destroy(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "The status of this row in the table. The only allowable actions are to retrieve the status, which will be 'active', or to set the status to 'destroy' in order to remove this entry from the cache. Row creation is not permitted. No columnar objects are writable, so there are none that may be changed while the status value is active(1)." ::= { msdpSACacheEntry 10 } -- -- MSDP Mesh Group Membership table -- msdpMeshGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF MsdpMeshGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing MSDP Mesh Group configuration." ::= { msdp 12 } msdpMeshGroupEntry OBJECT-TYPE SYNTAX MsdpMeshGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing a peer in an MSDP Mesh Group. If row creation is supported, dynamically added rows are added to the system's stable configuration (corresponding to a StorageType value of nonVolatile)." INDEX { msdpMeshGroupName, msdpMeshGroupPeerAddress } ::= { msdpMeshGroupTable 1 } MsdpMeshGroupEntry ::= SEQUENCE { msdpMeshGroupName DisplayString, msdpMeshGroupPeerAddress IpAddress, msdpMeshGroupStatus RowStatus } msdpMeshGroupName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..64)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of the mesh group." ::= { msdpMeshGroupEntry 1 } msdpMeshGroupPeerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "A peer address that is a member of the mesh group with name msdpMeshGroupName. The msdpMeshGroupPeerAddress must match a row in the msdpPeerTable." ::= { msdpMeshGroupEntry 2 } msdpMeshGroupStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This entry's status, by which new entries may be added to the table and old entries deleted. msdpMeshGroupName and msdpMeshGroupPeerAddress must be set to valid values before the row can be activated. Since these are the table's INDEX, a row can be activated by simply setting the msdpMeshGroupStatus variable. It is not possible to modify other columns in the same conceptual row when the status value is active(1), because the only other objects in the row are part of the INDEX. Changing one of these changes the row, so an old row must be deleted and a new one created." ::= { msdpMeshGroupEntry 3 } -- Traps msdpTraps OBJECT IDENTIFIER ::= { msdp 0 } msdpEstablished NOTIFICATION-TYPE OBJECTS { msdpPeerFsmEstablishedTransitions } STATUS current DESCRIPTION "The MSDP Established event is generated when the MSDP FSM enters the ESTABLISHED state." ::= { msdpTraps 1 } msdpBackwardTransition NOTIFICATION-TYPE OBJECTS { msdpPeerState } STATUS current DESCRIPTION "The MSDPBackwardTransition Event is generated when the MSDP FSM moves from a higher-numbered state to a lower-numbered state." ::= { msdpTraps 2 } -- conformance information msdpMIBConformance OBJECT IDENTIFIER ::= { msdp 8 } msdpMIBCompliances OBJECT IDENTIFIER ::= { msdpMIBConformance 1 } msdpMIBGroups OBJECT IDENTIFIER ::= { msdpMIBConformance 2 } -- compliance statements msdpMIBCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for entities that implement a pre- RFC version of MSDP. This statement is deprecated because it includes objects used for managing/monitoring aspects of MSDP that were removed before it was published as an RFC." MODULE -- this module MANDATORY-GROUPS { msdpMIBGlobalsGroup, msdpMIBPeerGroup, msdpMIBNotificationGroup } GROUP msdpMIBEncapsulationGroup DESCRIPTION "This group is mandatory if MSDP encapsulation interfaces are not given their own interface index numbers." GROUP msdpMIBSACacheGroup DESCRIPTION "This group is mandatory if the MSDP speaker has the ability to cache SA messages." GROUP msdpMIBRequestsGroup DESCRIPTION "This group is mandatory if the MSDP speaker has the ability to send SA-Request messages and to parse SA-Response messages." GROUP msdpMIBRPGroup DESCRIPTION "This group is mandatory if the MSDP speaker sources (as opposed to forwards) MSDP messages." GROUP msdpMIBMeshGroupGroup DESCRIPTION "This group is mandatory if the MSDP speaker can participate in MSDP Mesh Groups." ::= { msdpMIBCompliances 1 } msdpMIBFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities that implement MSDP (RFC3618)." MODULE -- this module MANDATORY-GROUPS { msdpMIBGlobalsGroup, msdpMIBPeerGroup2, msdpMIBSACacheGroup, msdpMIBEncapsulationGroup } GROUP msdpMIBRPGroup DESCRIPTION "This group is mandatory if the MSDP speaker sources (as opposed to forwards) MSDP messages." GROUP msdpMIBMeshGroupGroup DESCRIPTION "This group is mandatory if the MSDP speaker can participate in MSDP Mesh Groups." ::= { msdpMIBCompliances 2 } msdpMIBReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities that implement MSDP (RFC3618), but do not permit configuration (or only permit partial configuration) via SNMP." MODULE -- this module MANDATORY-GROUPS { msdpMIBGlobalsGroup, msdpMIBPeerGroup2, msdpMIBSACacheGroup, msdpMIBEncapsulationGroup } GROUP msdpMIBRPGroup DESCRIPTION "This group is mandatory if the MSDP speaker sources (as opposed to forwards) MSDP messages." GROUP msdpMIBMeshGroupGroup DESCRIPTION "This group is mandatory if the MSDP speaker can participate in MSDP Mesh Groups." OBJECT msdpEnabled MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT msdpCacheLifetime MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT msdpPeerLocalAddress MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT msdpPeerConnectRetryInterval MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT msdpPeerHoldTimeConfigured MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT msdpPeerKeepAliveConfigured MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT msdpPeerDataTtl MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT msdpPeerStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT msdpPeerEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT msdpSACacheStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT msdpRPAddress MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT msdpMeshGroupStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { msdpMIBCompliances 3 } -- units of conformance msdpMIBGlobalsGroup OBJECT-GROUP OBJECTS { msdpEnabled } STATUS current DESCRIPTION "A collection of objects providing information on global MSDP state." ::= { msdpMIBGroups 1 } msdpMIBPeerGroup OBJECT-GROUP OBJECTS { msdpPeerRPFFailures, msdpPeerState, msdpPeerInSAs, msdpPeerOutSAs, msdpPeerInSARequests, msdpPeerOutSARequests, msdpPeerInSAResponses, msdpPeerOutSAResponses, msdpPeerInNotifications, msdpPeerOutNotifications, msdpPeerInControlMessages, msdpPeerOutControlMessages, msdpPeerFsmEstablishedTransitions, msdpPeerFsmEstablishedTime, msdpPeerLocalAddress, msdpPeerRemotePort, msdpPeerLocalPort, msdpPeerConnectRetryInterval, msdpPeerHoldTimeConfigured, msdpPeerKeepAliveConfigured, msdpPeerInMessageTime, msdpPeerProcessRequestsFrom, msdpPeerConnectionAttempts, msdpPeerLastError, msdpPeerStatus, msdpPeerDiscontinuityTime } STATUS deprecated DESCRIPTION "A collection of objects for managing MSDP peers. This group is deprecated in favor of msdpMIBPeerGroup2 because it contains objects for managing aspects of MSDP that were removed before it was published as an RFC." ::= { msdpMIBGroups 2 } msdpMIBEncapsulationGroup OBJECT-GROUP OBJECTS { msdpPeerInDataPackets, msdpPeerOutDataPackets, msdpPeerDataTtl, msdpPeerEncapsulationType } STATUS current DESCRIPTION "A collection of objects for managing encapsulations if the MSDP encapsulation interfaces are not given interface indices." ::= { msdpMIBGroups 3 } msdpMIBSACacheGroup OBJECT-GROUP OBJECTS { msdpCacheLifetime, msdpNumSACacheEntries, msdpSACachePeerLearnedFrom, msdpSACacheRPFPeer, msdpSACacheInSAs, msdpSACacheInDataPackets, msdpSACacheUpTime, msdpSACacheExpiryTime, msdpSACacheStatus } STATUS current DESCRIPTION "A collection of objects for managing MSDP SA cache entries." ::= { msdpMIBGroups 4 } msdpMIBNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { msdpEstablished, msdpBackwardTransition } STATUS current DESCRIPTION "A collection of notifications for signaling changes in MSDP peer relationships." ::= { msdpMIBGroups 5 } msdpMIBRequestsGroup OBJECT-GROUP OBJECTS { msdpRequestsPeer, msdpRequestsStatus } STATUS deprecated DESCRIPTION "A collection of objects for managing MSDP Request transmission. This group is deprecated because Requests were removed from MSDP before its publication as an RFC." ::= { msdpMIBGroups 6 } msdpMIBRPGroup OBJECT-GROUP OBJECTS { msdpRPAddress } STATUS current DESCRIPTION "A collection of objects for MSDP speakers that source MSDP messages." ::= { msdpMIBGroups 7 } msdpMIBMeshGroupGroup OBJECT-GROUP OBJECTS { msdpMeshGroupStatus } STATUS current DESCRIPTION "A collection of objects for MSDP speakers that can participate in MSDP mesh groups." ::= { msdpMIBGroups 8 } msdpMIBPeerGroup2 OBJECT-GROUP OBJECTS { msdpPeerRPFFailures, msdpPeerState, msdpPeerInSAs, msdpPeerOutSAs, msdpPeerInSARequests, msdpPeerOutSARequests, msdpPeerInControlMessages, msdpPeerOutControlMessages, msdpPeerFsmEstablishedTransitions, msdpPeerFsmEstablishedTime, msdpPeerLocalAddress, msdpPeerRemotePort, msdpPeerLocalPort, msdpPeerConnectRetryInterval, msdpPeerHoldTimeConfigured, msdpPeerKeepAliveConfigured, msdpPeerInMessageTime, msdpPeerConnectionAttempts, msdpPeerStatus, msdpPeerDiscontinuityTime } STATUS current DESCRIPTION "A collection of objects for managing MSDP peers." ::= { msdpMIBGroups 9 } END -- =========================================================================== -- Full Copyright Statement -- -- Copyright (C) The Internet Society (2004). This document is subject -- to the rights, licenses and restrictions contained in BCP 78, and -- except as set forth therein, the authors retain all their rights. -- -- This document and the information contained herein are provided on an -- "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS -- OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET -- ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, -- INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE -- INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED -- WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. -- -- Intellectual Property -- -- The IETF takes no position regarding the validity or scope of any -- Intellectual Property Rights or other rights that might be claimed to -- pertain to the implementation or use of the technology described in -- this document or the extent to which any license under such rights -- might or might not be available; nor does it represent that it has -- made any independent effort to identify any such rights. Information -- on the procedures with respect to rights in RFC documents can be -- found in BCP 78 and BCP 79. -- -- Copies of IPR disclosures made to the IETF Secretariat and any -- assurances of licenses to be made available, or the result of an -- attempt made to obtain a general license or permission for the use of -- such proprietary rights by implementers or users of this -- specification can be obtained from the IETF on-line IPR repository at -- http://www.ietf.org/ipr. -- -- The IETF invites any interested party to bring to its attention any -- copyrights, patents or patent applications, or other proprietary -- rights that may cover technology that may be required to implement -- this standard. Please address the information to the IETF at ietf- -- ipr@ietf.org. -- -- Acknowledgement -- -- Funding for the RFC Editor function is currently provided by the -- Internet Society. -- ===========================================================================