x/compass-core
Code Issues Proposed changes
0a57fe8f4b
compass-core/mibs/HUAWEI-OSPFV3-MIB.mib

3190 lines
128 KiB
Plaintext
Raw Blame History

-- ==================================================================
-- Copyright (C) 2007 by HUAWEI TECHNOLOGIES. All rights reserved.
--
-- Description: HUAWEI-OSPFV3-MIB.mib, The HUAWEI-OSPFV3-MIB provides information about OSPFv3
-- Reference: draft-ietf-ospf-ospfv3-mib-11
-- Version: V1.0
-- History:
-- ==================================================================
HUAWEI-OSPFV3-MIB DEFINITIONS ::= BEGIN
IMPORTS
hwDatacomm
FROM HUAWEI-MIB
MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, mib-2,
Counter32, Gauge32, Integer32, Unsigned32
FROM SNMPv2-SMI
TEXTUAL-CONVENTION, TruthValue, RowStatus
FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF
InterfaceIndex
FROM IF-MIB
InetAddressType, InetAddress, InetAddressPrefixLength
FROM INET-ADDRESS-MIB
Metric, BigMetric, Status,
HelloRange, DesignatedRouterPriority
FROM OSPF-MIB;
hwOspfv3 MODULE-IDENTITY
LAST-UPDATED "200706122000Z"
ORGANIZATION
"Huawei Technologies co., Ltd."
CONTACT-INFO
" R&D BeiJing, Huawei Technologies co.,Ltd.
Huawei Bld.,NO.3 Xinxi Rd.,
Shang-Di Information Industry Base,
Hai-Dian District Beijing P.R. China
Zip:100085
Http://www.huawei.com
E-mail:support@huawei.com "
DESCRIPTION
"The MIB module for OSPF version 3.
Copyright (C) The Internet Society (2006).
This version of this MIB module is part of
RFC draft-ietf-ospf-ospfv3-mib-11;
see the RFC itself for full legal
notices."
REVISION "200706122100Z"
DESCRIPTION -- RFC Editor assigns RFC xxxx
"Initial version, published as RFC xxxx"
::= { hwDatacomm 147 }
-- Texual conventions
HWOspfv3UpToRefreshIntervalTc ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"The values one might be able to configure for
variables bounded by the Refresh Interval"
SYNTAX Unsigned32 (0..3600)
HWOspfv3DeadIntRangeTc ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"The range, in seconds, of dead interval value."
SYNTAX Unsigned32 (0..'FFFF'h)
HWOspfv3RouterIdTc ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"A 32-bit, unsigned integer uniquely identifying the
router in the Autonomous System. To ensure uniqueness,
this may default to the value of one of the router's
IPv4 host addresses if IPv4 is configured on the
router."
SYNTAX Unsigned32 (0..'FFFFFFFF'h)
HWOspfv3LsIdTC ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"A unique 32-bit identifier of the piece of the
routing domain that is being described by a link
state advertisement. In contrast to OSPFv2, the
Link State ID (LSID) has no addressing semantics."
REFERENCE
"OSPF Version 2, Section 12.1.4, Link State ID"
SYNTAX Unsigned32 (1..'FFFFFFFF'h)
HWOspfv3AreaIdTc ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"An OSPFv3 Area Identifier"
SYNTAX Unsigned32 (0..'FFFFFFFF'h)
HWOspfv3IfInstIdTc ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"An OSPFv3 interface instance ID"
SYNTAX Unsigned32 (0..255)
HWOspfv3LsaSequenceTC ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"The sequence number field is a signed 32-bit
integer. It is used to detect old and duplicate
link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number, the more recent the
advertisement."
REFERENCE
"OSPF Version 2, Section 12.1.6, LS sequence
number"
SYNTAX Integer32
HWOspfv3LsaAgeTC ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"The age of the link state advertisement in
seconds. The high-order bit of the LS age
field is considered the DoNotAge bit for
support of on-demand circuits."
REFERENCE
"OSPF Version 2, Section 12.1.1, LS age;
Extending OSPF to Support Demand Circuits,
Section 2.2, The LS age field"
SYNTAX Unsigned32 (0..3600 | 32768..36368)
HWHelloRange ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The range of intervals on which hello messages are
exchanged."
SYNTAX Integer32 (0..65535)
-- Top-level structure of MIB
hwOspfv3Notifications OBJECT IDENTIFIER ::= { hwOspfv3 0 }
hwOspfv3Objects OBJECT IDENTIFIER ::= { hwOspfv3 1 }
hwOspfv3Conformance OBJECT IDENTIFIER ::= { hwOspfv3 2 }
-- OSPFv3 General Variables
-- These parameters apply globally to the Router's
-- OSPFv3 Process.
hwOspfv3GeneralGroup OBJECT IDENTIFIER ::= { hwOspfv3Objects 1 }
hwOspfv3RouterId OBJECT-TYPE
SYNTAX HWOspfv3RouterIdTc
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A 32-bit integer uniquely identifying the
router in the Autonomous System. To ensure
uniqueness, this may default to the value of
one of the router's IPv4 host addresses,
represented as a 32-bit unsigned integer,
if IPv4 is configured on the router."
::= { hwOspfv3GeneralGroup 1 }
hwOspfv3AdminStatus OBJECT-TYPE
SYNTAX Status
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The administrative status of OSPFv3 in the
router. The value 'enabled' denotes that the
OSPFv3 Process is active on at least one
interface; 'disabled' disables it on all
interfaces."
::= { hwOspfv3GeneralGroup 2 }
hwOspfv3VersionNumber OBJECT-TYPE
SYNTAX INTEGER { version3 (3) }
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The version number of OSPF for IPv6 is 3."
::= { hwOspfv3GeneralGroup 3 }
hwOspfv3AreaBdrRtrStatus OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A flag to note whether this router is an area
border router."
REFERENCE
"OSPF Version 2, Section 3 Splitting the AS into
Areas"
::= { hwOspfv3GeneralGroup 4 }
hwOspfv3AsBdrRtrStatus OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A flag to note whether this router is
configured as an Autonomous System border router."
REFERENCE
"OSPF Version 2, Section 3.3 Classification of
routers"
::= { hwOspfv3GeneralGroup 5 }
hwOspfv3AsScopeLsaCount OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of AS-Scope (e.g. AS-External) link state
advertisements in the link state database."
::= { hwOspfv3GeneralGroup 6 }
hwOspfv3AsScopeLsaCksumSum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 32-bit unsigned sum of the LS checksums of
the AS-scoped link state advertisements
contained in the link state database. This sum
can be used to determine if there has been a
change in a router's link state database, and
to compare the link state database of two
routers."
::= { hwOspfv3GeneralGroup 7 }
hwOspfv3OriginateNewLsas OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of new link-state advertisements
that have been originated. This number is
incremented each time the router originates a new
LSA."
::= { hwOspfv3GeneralGroup 8 }
hwOspfv3RxNewLsas OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of link state advertisements
received determined to be new instantiations.
This number does not include newer
instantiations of self-originated link state
advertisements."
::= { hwOspfv3GeneralGroup 9 }
hwOspfv3ExtLsaCount OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of AS-Scope External(LS type 0x4005) link state
advertisements in the link state database"
::= { hwOspfv3GeneralGroup 10 }
hwOspfv3ExtAreaLsdbLimit OBJECT-TYPE
SYNTAX Integer32 (-1..'7FFFFFFF'h)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum number of non-default
AS-external-LSAs entries that can be stored in the
link state database. If the value is -1, then
there is no limit.
When the number of non-default AS-external-LSAs
in a router's link-state database reaches
ospfv3ExtAreaLsdbLimit, the router enters Overflow
state. The router never holds more than
ospfv3ExtAreaLsdbLimit non-default AS-external-LSAs
in its database. Ospfv3ExtAreaLsdbLimit MUST be set
identically in all routers attached to the OSPFv3
backbone and/or any regular OSPFv3 area. (i.e.,
OSPFv3 stub areas and NSSAs are excluded)."
::= { hwOspfv3GeneralGroup 11 }
hwOspfv3RestartSupport OBJECT-TYPE
SYNTAX INTEGER { none (1),
plannedOnly (2),
plannedAndUnplanned (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The router's support for OSPFv3 Graceful restart.
Options include: no restart support, only planned
restarts or both planned and unplanned restarts."
::= { hwOspfv3GeneralGroup 12 }
hwOspfv3RestartInterval OBJECT-TYPE
SYNTAX HWOspfv3UpToRefreshIntervalTc
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Configured OSPFv3 Graceful restart timeout interval."
::= { hwOspfv3GeneralGroup 13 }
hwOspfv3RestartStatus OBJECT-TYPE
SYNTAX INTEGER { notRestarting (1),
plannedRestart (2),
unplannedRestart (3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current status of OSPFv3 Graceful restart capability."
::= { hwOspfv3GeneralGroup 14 }
hwOspfv3RestartAge OBJECT-TYPE
SYNTAX HWOspfv3UpToRefreshIntervalTc
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Remaining time in current OSPFv3 Graceful restart
interval."
::= { hwOspfv3GeneralGroup 15 }
hwOspfv3RestartExitRc OBJECT-TYPE
SYNTAX INTEGER { none (1),
inProgress (2),
completed (3),
timedOut (4),
topologyChanged (5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Describes the outcome of the last attempt at a
Graceful restart.
none:............no restart has yet been attempted.
inProgress:......a restart attempt is currently underway.
completed:.......the last restart completed successfully.
timedOut:........the last restart timed out.
topologyChanged:.the last restart was aborted due to
a topology change."
::= { hwOspfv3GeneralGroup 16 }
hwOspfv3NotificationEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If this object is set to true(1), then it enables
the generation of OSPFv3 Notifications. If it is
set to false(2), these notifications are not
generated.
Configured values MUST survive an agent reboot."
::= { hwOspfv3GeneralGroup 17 }
hwOspfv3ReferenceBandwidth OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Reference bandwidth in kilobits per second for
calculating default interface metrics. The
default value is 100,000 KBPS (100 MBPS).
This object is persistent, and when written, the
entity SHOULD save the change to non-volatile
storage."
::= { hwOspfv3GeneralGroup 18 }
-- The OSPFv3 Area Data Structure contains information
-- regarding the various areas. The interfaces and
-- virtual links are configured as part of these areas.
-- Area 0, by definition, is the Backbone Area
hwOspfv3AreaTable OBJECT-TYPE
SYNTAX SEQUENCE OF HwOspfv3AreaEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information describing the configured
parameters and cumulative statistics of the router's
attached areas."
REFERENCE
"OSPF Version 2, Section 6 The Area Data
Structure"
::= { hwOspfv3Objects 2 }
hwOspfv3AreaEntry OBJECT-TYPE
SYNTAX HwOspfv3AreaEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information describing the configured
parameters and cumulative statistics of one of the
router's attached areas."
INDEX { hwOspfv3AreaId }
::= { hwOspfv3AreaTable 1 }
HwOspfv3AreaEntry ::= SEQUENCE {
hwOspfv3AreaId
HWOspfv3AreaIdTc,
hwOspfv3AreaImportAsExtern
INTEGER,
hwOspfv3AreaSpfRuns
Counter32,
hwOspfv3AreaBdrRtrCount
Gauge32,
hwOspfv3AreaAsBdrRtrCount
Gauge32,
hwOspfv3AreaScopeLsaCount
Gauge32,
hwOspfv3AreaScopeLsaCksumSum
Unsigned32,
hwOspfv3AreaSummary
INTEGER,
hwOspfv3AreaRowStatus
RowStatus,
hwOspfv3AreaStubMetric
BigMetric,
hwOspfv3AreaNssaTranslatorRole
INTEGER,
hwOspfv3AreaNssaTranslatorState
INTEGER,
hwOspfv3AreaNssaTranslatorStabInterval
Unsigned32,
hwOspfv3AreaNssaTranslatorEvents
Counter32
}
hwOspfv3AreaId OBJECT-TYPE
SYNTAX HWOspfv3AreaIdTc
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A 32-bit integer uniquely identifying an area.
Area ID 0 is used for the OSPFv3 backbone."
REFERENCE
"OSPF Version 2, Appendix C.2 Area parameters"
::= { hwOspfv3AreaEntry 1 }
hwOspfv3AreaImportAsExtern OBJECT-TYPE
SYNTAX INTEGER {
importExternal(1), -- normal area
importNoExternal(2), -- stub area
importNssa(3) -- not-so-stubby-area
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates whether an area is a Stub area, NSSA, or
standard area. AS-scope LSAs are not imported into Stub
Areas or NSSAs. NSSAs import AS-External data as NSSA
LSAs which have Area-scope"
REFERENCE
"OSPF Version 2, Appendix C.2 Area parameters"
DEFVAL { importExternal }
::= { hwOspfv3AreaEntry 2 }
hwOspfv3AreaSpfRuns OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times that the intra-area route
table has been calculated using this area's
link state database. This is typically done
using Dijkstra's algorithm."
::= { hwOspfv3AreaEntry 3 }
hwOspfv3AreaBdrRtrCount OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of area border routers
reachable within this area. This is initially zero,
and is calculated in each SPF Pass."
::= { hwOspfv3AreaEntry 4 }
hwOspfv3AreaAsBdrRtrCount OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of Autonomous System border
routers reachable within this area. This is
initially zero, and is calculated in each SPF
Pass."
::= { hwOspfv3AreaEntry 5 }
hwOspfv3AreaScopeLsaCount OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of Area-Scope link state
advertisements in this area's link state
database."
::= { hwOspfv3AreaEntry 6 }
hwOspfv3AreaScopeLsaCksumSum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 32-bit unsigned sum of the Area-Scope link state
advertisements' LS checksums contained in this
area's link state database. The sum can be used
to determine if there has been a change in a
router's link state database, and to compare the
link-state database of two routers."
::= { hwOspfv3AreaEntry 7 }
hwOspfv3AreaSummary OBJECT-TYPE
SYNTAX INTEGER {
noAreaSummary(1),
sendAreaSummary(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The variable ospfv3AreaSummary controls the
import of Inter-Area LSAs into stub and
NSSA areas. It has no effect on other areas.
If it is noAreaSummary, the router will neither
originate nor propagate Inter-Area LSAs into the
stub or NSSA area. It will rely entirely on its
default route.
If it is sendAreaSummary, the router will both
summarize and propagate Inter-Area LSAs."
DEFVAL { sendAreaSummary }
::= { hwOspfv3AreaEntry 8 }
hwOspfv3AreaRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object permits management of the table by
facilitating actions such as row creation,
construction and destruction.
The value of this object has no effect on
whether other objects in this conceptual row can be
modified."
::= { hwOspfv3AreaEntry 9 }
hwOspfv3AreaStubMetric OBJECT-TYPE
SYNTAX BigMetric
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The metric value advertised for the default route
into Stub and NSSA areas."
::= { hwOspfv3AreaEntry 10 }
hwOspfv3AreaNssaTranslatorRole OBJECT-TYPE
SYNTAX INTEGER { always(1), candidate(2) }
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates an NSSA border router's policy to
perform NSSA translation of NSSA-LSAs into
AS-External-LSAs."
DEFVAL { candidate }
::= { hwOspfv3AreaEntry 11 }
hwOspfv3AreaNssaTranslatorState OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
elected(2),
disabled(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates if and how an NSSA border router is
performing NSSA translation of NSSA-LSAs into
AS-External-LSAs. When this object is set to
'enabled', the NSSA border router's
ospfv3AreaNssaTranslatorRole has been set to 'always'.
When this object is set to 'elected', a candidate
NSSA border router is translating NSSA-LSAs into
AS-External-LSAs. When this object is set to
'disabled', a candidate NSSA Border router is NOT
translating NSSA-LSAs into AS-External-LSAs."
::= { hwOspfv3AreaEntry 12 }
hwOspfv3AreaNssaTranslatorStabInterval OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The stability interval defined as the number of
seconds after an elected translator determines its
services are no longer required that it should
continue to perform its translation duties."
DEFVAL { 40 }
::= { hwOspfv3AreaEntry 13 }
hwOspfv3AreaNssaTranslatorEvents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the number of Translator state changes
that have occurred since the last start-up of the
OSPFv3 routing process.
Discontinuities in the value of this counter
can occur at re-initialization of the management
system and at other times as indicated by the
value of ospfv3DiscontinuityTime."
::= { hwOspfv3AreaEntry 14 }
-- OSPFv3 AS-Scope Link State Database
-- The Link State Database contains the AS-Scope Link State
-- Advertisements from throughout the areas that the
-- device is attached to.
hwOspfv3AsLsdbTable OBJECT-TYPE
SYNTAX SEQUENCE OF HwOspfv3AsLsdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPFv3 Process's AS-Scope Link State Database."
::= { hwOspfv3Objects 3 }
hwOspfv3AsLsdbEntry OBJECT-TYPE
SYNTAX HwOspfv3AsLsdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A single AS-Scope Link State Advertisement."
INDEX { hwOspfv3AsLsdbType,
hwOspfv3AsLsdbRouterId,
hwOspfv3AsLsdbLsId }
::= { hwOspfv3AsLsdbTable 1 }
HwOspfv3AsLsdbEntry ::= SEQUENCE {
hwOspfv3AsLsdbType
Unsigned32,
hwOspfv3AsLsdbRouterId
HWOspfv3RouterIdTc,
hwOspfv3AsLsdbLsId
Unsigned32,
hwOspfv3AsLsdbSequence
HWOspfv3LsaSequenceTC,
hwOspfv3AsLsdbAge
HWOspfv3LsaAgeTC,
hwOspfv3AsLsdbChecksum
Integer32,
hwOspfv3AsLsdbAdvertisement
OCTET STRING,
hwOspfv3AsLsdbTypeKnown
TruthValue
}
hwOspfv3AsLsdbType OBJECT-TYPE
SYNTAX Unsigned32(0..'FFFFFFFF'h)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The type of the link state advertisement.
Each link state type has a separate
advertisement format. AS-Scope LSAs not recognized
by the router may be stored in the database."
::= { hwOspfv3AsLsdbEntry 1 }
hwOspfv3AsLsdbRouterId OBJECT-TYPE
SYNTAX HWOspfv3RouterIdTc
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The 32 bit number that uniquely identifies the
originating router in the Autonomous System."
REFERENCE
"OSPF Version 2, Appendix C.1 Global parameters"
::= { hwOspfv3AsLsdbEntry 2 }
hwOspfv3AsLsdbLsId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Link State ID is an LS Type Specific field
containing a unique identifier;
it identifies the piece of the routing domain
that is being described by the advertisement.
In contrast to OSPFv2, the LSID has no
addressing semantics."
::= { hwOspfv3AsLsdbEntry 3 }
-- Note that the OSPF Sequence Number is a 32 bit signed
-- integer. It starts with the value '80000001'h,
-- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h
-- Thus, a typical sequence number will be very negative.
hwOspfv3AsLsdbSequence OBJECT-TYPE
SYNTAX HWOspfv3LsaSequenceTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sequence number field is a signed 32-bit
integer. It is used to detect old and duplicate
link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number the more recent the
advertisement."
REFERENCE
"OSPF Version 2, Section 12.1.6 LS sequence
number"
::= { hwOspfv3AsLsdbEntry 4 }
hwOspfv3AsLsdbAge OBJECT-TYPE
SYNTAX HWOspfv3LsaAgeTC -- Should be 0..MaxAge
-- unless DoNotAge bit is set
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This field is the age of the link state
advertisement in seconds."
REFERENCE
"OSPF Version 2, Section 12.1.1 LS age"
::= { hwOspfv3AsLsdbEntry 5 }
hwOspfv3AsLsdbChecksum OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO
connectionless datagrams; it is commonly
referred to as the Fletcher checksum."
REFERENCE
"OSPF Version 2, Section 12.1.7 LS checksum"
::= { hwOspfv3AsLsdbEntry 6 }
hwOspfv3AsLsdbAdvertisement OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1..65535))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The entire Link State Advertisement, including
its header."
::= { hwOspfv3AsLsdbEntry 7 }
hwOspfv3AsLsdbTypeKnown OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether the LSA type is recognized by
this Router."
::= { hwOspfv3AsLsdbEntry 8 }
-- OSPFv3 Area-Scope Link State Database
-- The Link State Database contains the Area-Scope Link State
-- Advertisements from throughout the area that the
-- device is attached to.
hwOspfv3AreaLsdbTable OBJECT-TYPE
SYNTAX SEQUENCE OF HwOspfv3AreaLsdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPFv3 Process's Area-Scope Link State Database."
::= { hwOspfv3Objects 4 }
hwOspfv3AreaLsdbEntry OBJECT-TYPE
SYNTAX HwOspfv3AreaLsdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A single Area-Scope Link State Advertisement."
INDEX { hwOspfv3AreaLsdbAreaId,
hwOspfv3AreaLsdbType,
hwOspfv3AreaLsdbRouterId,
hwOspfv3AreaLsdbLsId }
::= { hwOspfv3AreaLsdbTable 1 }
HwOspfv3AreaLsdbEntry ::= SEQUENCE {
hwOspfv3AreaLsdbAreaId
HWOspfv3AreaIdTc,
hwOspfv3AreaLsdbType
Unsigned32,
hwOspfv3AreaLsdbRouterId
HWOspfv3RouterIdTc,
hwOspfv3AreaLsdbLsId
Unsigned32,
hwOspfv3AreaLsdbSequence
HWOspfv3LsaSequenceTC,
hwOspfv3AreaLsdbAge
HWOspfv3LsaAgeTC,
hwOspfv3AreaLsdbChecksum
Integer32,
hwOspfv3AreaLsdbAdvertisement
OCTET STRING,
hwOspfv3AreaLsdbTypeKnown
TruthValue
}
hwOspfv3AreaLsdbAreaId OBJECT-TYPE
SYNTAX HWOspfv3AreaIdTc
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The 32-bit identifier of the Area from which the
LSA was received."
REFERENCE
"OSPF Version 2, Appendix C.2 Area parameters"
::= { hwOspfv3AreaLsdbEntry 1 }
hwOspfv3AreaLsdbType OBJECT-TYPE
SYNTAX Unsigned32(0..'FFFFFFFF'h)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The type of the link state advertisement.
Each link state type has a separate
advertisement format. Area-Scope LSAs unrecognized
by the router are also stored in this database."
::= { hwOspfv3AreaLsdbEntry 2 }
hwOspfv3AreaLsdbRouterId OBJECT-TYPE
SYNTAX HWOspfv3RouterIdTc
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The 32-bit number that uniquely identifies the
originating router in the Autonomous System."
REFERENCE
"OSPF Version 2, Appendix C.1 Global parameters"
::= { hwOspfv3AreaLsdbEntry 3 }
hwOspfv3AreaLsdbLsId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Link State ID is an LS Type Specific field
containing a unique identifier;
it identifies the piece of the routing domain
that is being described by the advertisement.
In contrast to OSPFv2, the LSID has no
addressing semantics."
::= { hwOspfv3AreaLsdbEntry 4 }
-- Note that the OSPF Sequence Number is a 32 bit signed
-- integer. It starts with the value '80000001'h,
-- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h
-- Thus, a typical sequence number will be very negative.
hwOspfv3AreaLsdbSequence OBJECT-TYPE
SYNTAX HWOspfv3LsaSequenceTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sequence number field is a signed 32-bit
integer. It is used to detect old and
duplicate link state advertisements. The space
of sequence numbers is linearly ordered. The
larger the sequence number the more recent the
advertisement."
REFERENCE
"OSPF Version 2, Section 12.1.6 LS sequence
number"
::= { hwOspfv3AreaLsdbEntry 5 }
hwOspfv3AreaLsdbAge OBJECT-TYPE
SYNTAX HWOspfv3LsaAgeTC -- Should be 0..MaxAge
-- unless DoNotAge bit is set
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This field is the age of the link state
advertisement in seconds."
REFERENCE
"OSPF Version 2, Section 12.1.1 LS age"
::= { hwOspfv3AreaLsdbEntry 6 }
hwOspfv3AreaLsdbChecksum OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO
connectionless datagrams; it is commonly
referred to as the Fletcher checksum."
REFERENCE
"OSPF Version 2, Section 12.1.7 LS checksum"
::= { hwOspfv3AreaLsdbEntry 7 }
hwOspfv3AreaLsdbAdvertisement OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1..65535))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The entire Link State Advertisement, including
its header."
::= { hwOspfv3AreaLsdbEntry 8 }
hwOspfv3AreaLsdbTypeKnown OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether the LSA type is recognized
by this Router."
::= { hwOspfv3AreaLsdbEntry 9 }
-- OSPFv3 Link-Scope Link State Database
-- The Link State Database contains the Link-Scope Link State
-- Advertisements from the links that the
-- device is attached to.
hwOspfv3LinkLsdbTable OBJECT-TYPE
SYNTAX SEQUENCE OF HwOspfv3LinkLsdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPFv3 Process's Link-Scope Link State Database."
::= { hwOspfv3Objects 5 }
hwOspfv3LinkLsdbEntry OBJECT-TYPE
SYNTAX HwOspfv3LinkLsdbEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A single Link-Scope Link State Advertisement."
INDEX { hwOspfv3LinkLsdbIfIndex,
hwOspfv3LinkLsdbIfInstId,
hwOspfv3LinkLsdbType,
hwOspfv3LinkLsdbRouterId,
hwOspfv3LinkLsdbLsId }
::= { hwOspfv3LinkLsdbTable 1 }
HwOspfv3LinkLsdbEntry ::= SEQUENCE {
hwOspfv3LinkLsdbIfIndex
InterfaceIndex,
hwOspfv3LinkLsdbIfInstId
HWOspfv3IfInstIdTc,
hwOspfv3LinkLsdbType
Unsigned32,
hwOspfv3LinkLsdbRouterId
HWOspfv3RouterIdTc,
hwOspfv3LinkLsdbLsId
HWOspfv3LsIdTC,
hwOspfv3LinkLsdbSequence
HWOspfv3LsaSequenceTC,
hwOspfv3LinkLsdbAge
HWOspfv3LsaAgeTC,
hwOspfv3LinkLsdbChecksum
Integer32,
hwOspfv3LinkLsdbAdvertisement
OCTET STRING,
hwOspfv3LinkLsdbTypeKnown
TruthValue
}
hwOspfv3LinkLsdbIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The identifier of the link from which the LSA
was received."
::= { hwOspfv3LinkLsdbEntry 1 }
hwOspfv3LinkLsdbIfInstId OBJECT-TYPE
SYNTAX HWOspfv3IfInstIdTc
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The identifier of the interface instance from
which the LSA was received."
::= { hwOspfv3LinkLsdbEntry 2 }
hwOspfv3LinkLsdbType OBJECT-TYPE
SYNTAX Unsigned32(0..'FFFFFFFF'h)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The type of the link state advertisement.
Each link state type has a separate
advertisement format. Link-Scope LSAs unrecognized
by the router are also stored in this database."
::= { hwOspfv3LinkLsdbEntry 3 }
hwOspfv3LinkLsdbRouterId OBJECT-TYPE
SYNTAX HWOspfv3RouterIdTc
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The 32 bit number that uniquely identifies the
originating router in the Autonomous System."
REFERENCE
"OSPF Version 2, Appendix C.1 Global parameters"
::= { hwOspfv3LinkLsdbEntry 4 }
hwOspfv3LinkLsdbLsId OBJECT-TYPE
SYNTAX HWOspfv3LsIdTC
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Link State ID is an LS Type Specific field
containing a unique identifier;
it identifies the piece of the routing domain
that is being described by the advertisement.
In contrast to OSPFv2, the LSID has no
addressing semantics."
::= { hwOspfv3LinkLsdbEntry 5 }
-- Note that the OSPF Sequence Number is a 32 bit signed
-- integer. It starts with the value '80000001'h,
-- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h
-- Thus, a typical sequence number will be very negative.
hwOspfv3LinkLsdbSequence OBJECT-TYPE
SYNTAX HWOspfv3LsaSequenceTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sequence number field is a signed 32-bit
integer. It is used to detect old and duplicate
link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number the more recent the
advertisement."
REFERENCE
"OSPF Version 2, Section 12.1.6 LS sequence
number"
::= { hwOspfv3LinkLsdbEntry 6 }
hwOspfv3LinkLsdbAge OBJECT-TYPE
SYNTAX HWOspfv3LsaAgeTC -- Should be 0..MaxAge
-- unless DoNotAge bit is set
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This field is the age of the link state
advertisement in seconds."
REFERENCE
"OSPF Version 2, Section 12.1.1 LS age"
::= { hwOspfv3LinkLsdbEntry 7 }
hwOspfv3LinkLsdbChecksum OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checksum. The checksum
used is the same that is used for ISO
connectionless datagrams; it is commonly
referred to as the Fletcher checksum."
REFERENCE
"OSPF Version 2, Section 12.1.7 LS checksum"
::= { hwOspfv3LinkLsdbEntry 8 }
hwOspfv3LinkLsdbAdvertisement OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1..65535))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The entire Link State Advertisement, including
its header."
::= { hwOspfv3LinkLsdbEntry 9 }
hwOspfv3LinkLsdbTypeKnown OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether the LSA type is recognized by this
Router."
::= { hwOspfv3LinkLsdbEntry 10 }
-- OSPFv3 Interface Table
hwOspfv3IfTable OBJECT-TYPE
SYNTAX SEQUENCE OF HwOspfv3IfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPFv3 Interface Table describes the
interfaces from the viewpoint of OSPFv3."
REFERENCE
"OSPF Version 2, Appendix C.3 Router interface
parameters"
::= { hwOspfv3Objects 6 }
hwOspfv3IfEntry OBJECT-TYPE
SYNTAX HwOspfv3IfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The OSPFv3 Interface Entry describes one
interface from the viewpoint of OSPFv3."
INDEX { hwOspfv3IfIndex,
hwOspfv3IfInstId }
::= { hwOspfv3IfTable 1 }
HwOspfv3IfEntry ::= SEQUENCE {
hwOspfv3IfIndex
InterfaceIndex,
hwOspfv3IfInstId
HWOspfv3IfInstIdTc,
hwOspfv3IfAreaId
HWOspfv3AreaIdTc,
hwOspfv3IfType
INTEGER,
hwOspfv3IfAdminStatus
Status,
hwOspfv3IfRtrPriority
DesignatedRouterPriority,
hwOspfv3IfTransitDelay
HWOspfv3UpToRefreshIntervalTc,
hwOspfv3IfRetransInterval
HWOspfv3UpToRefreshIntervalTc,
hwOspfv3IfHelloInterval
HWHelloRange,
hwOspfv3IfRtrDeadInterval
HWOspfv3DeadIntRangeTc,
hwOspfv3IfState
INTEGER,
hwOspfv3IfDesignatedRouter
HWOspfv3RouterIdTc,
hwOspfv3IfBackupDesignatedRouter
HWOspfv3RouterIdTc,
hwOspfv3IfEvents
Counter32,
hwOspfv3IfRowStatus
RowStatus,
hwOspfv3IfMetricValue
Metric,
hwOspfv3IfLinkScopeLsaCount
Gauge32,
hwOspfv3IfLinkLsaCksumSum
Unsigned32,
hwOspfv3IfPollInterval
Unsigned32,
hwOspfv3IfMulticastForwarding
INTEGER
}
hwOspfv3IfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interface index of this OSPFv3 interface.
It corresponds to the interface index of the
IPv6 interface on which OSPFv3 is configured."
::= { hwOspfv3IfEntry 1 }
hwOspfv3IfInstId OBJECT-TYPE
SYNTAX HWOspfv3IfInstIdTc
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Enables multiple interface instances of OSPFv3
to be run over a single link. Each protocol
instance would be assigned a separate ID. This ID
has local link significance only."
::= { hwOspfv3IfEntry 2 }
hwOspfv3IfAreaId OBJECT-TYPE
SYNTAX HWOspfv3AreaIdTc
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A 32-bit integer uniquely identifying the area
to which the interface connects. Area ID
0 is used for the OSPFv3 backbone."
DEFVAL { 0 }
::= { hwOspfv3IfEntry 3 }
hwOspfv3IfType OBJECT-TYPE
SYNTAX INTEGER {
broadcast(1),
nbma(2),
pointToPoint(3),
loopback(4),
pointToMultipoint(5),
p2mpNonbroadcast(6)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The OSPFv3 interface type."
::= { hwOspfv3IfEntry 4 }
hwOspfv3IfAdminStatus OBJECT-TYPE
SYNTAX Status
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The OSPFv3 interface's administrative status.
The value formed on the interface, and the
interface will be advertised as an internal route
to some area. The value 'disabled' denotes
that the interface is external to OSPFv3."
DEFVAL { enabled }
::= { hwOspfv3IfEntry 5 }
hwOspfv3IfRtrPriority OBJECT-TYPE
SYNTAX DesignatedRouterPriority
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The priority of this interface. Used in
multi-access networks, this field is used in
the designated router election algorithm. The
value 0 signifies that the router is not
eligible to become the designated router on this
particular network. In the event of a tie in
this value, routers will use their Router ID as
a tie breaker."
DEFVAL { 1 }
::= { hwOspfv3IfEntry 6 }
hwOspfv3IfTransitDelay OBJECT-TYPE
SYNTAX HWOspfv3UpToRefreshIntervalTc
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The estimated number of seconds it takes to
transmit a link state update packet over this
interface."
DEFVAL { 1 }
::= { hwOspfv3IfEntry 7 }
hwOspfv3IfRetransInterval OBJECT-TYPE
SYNTAX HWOspfv3UpToRefreshIntervalTc
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds between link state
advertisement retransmissions, for adjacencies
belonging to this interface. This value is
also used when retransmitting database
description and link state request packets."
DEFVAL { 5 }
::= { hwOspfv3IfEntry 8 }
hwOspfv3IfHelloInterval OBJECT-TYPE
SYNTAX HWHelloRange
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The length of time, in seconds, between the
Hello packets that the router sends on the
interface. This value must be the same for all
routers attached to a common network."
DEFVAL { 10 }
::= { hwOspfv3IfEntry 9 }
hwOspfv3IfRtrDeadInterval OBJECT-TYPE
SYNTAX HWOspfv3DeadIntRangeTc
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds that a router's Hello
packets have not been seen before its
neighbors declare the router down on the interface.
This should be some multiple of the Hello interval.
This value must be the same for all routers attached
to a common network."
DEFVAL { 40 }
::= { hwOspfv3IfEntry 10 }
hwOspfv3IfState OBJECT-TYPE
SYNTAX INTEGER {
down(1),
loopback(2),
waiting(3),
pointToPoint(4),
designatedRouter(5),
backupDesignatedRouter(6),
otherDesignatedRouter(7)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The OSPFv3 Interface State."
::= { hwOspfv3IfEntry 11 }
hwOspfv3IfDesignatedRouter OBJECT-TYPE
SYNTAX HWOspfv3RouterIdTc
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Router ID of the Designated Router."
::= { hwOspfv3IfEntry 12 }
hwOspfv3IfBackupDesignatedRouter OBJECT-TYPE
SYNTAX HWOspfv3RouterIdTc
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Router ID of the Backup Designated
Router."
::= { hwOspfv3IfEntry 13 }
hwOspfv3IfEvents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times this OSPFv3 interface has
changed its state, or an error has occurred."
::= { hwOspfv3IfEntry 14 }
hwOspfv3IfRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object permits management of the table by
facilitating actions such as row creation,
construction and destruction.
The value of this object has no effect on
whether other objects in this conceptual row can be
modified."
::= { hwOspfv3IfEntry 15 }
hwOspfv3IfMetricValue OBJECT-TYPE
SYNTAX Metric
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The metric assigned to this interface.
The default value of the Metric is
Reference Bandwidth / ifSpeed. The value
of the reference bandwidth is configured
by the ospfv3ReferenceBandwidth object."
::= { hwOspfv3IfEntry 16 }
hwOspfv3IfLinkScopeLsaCount OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of Link-Scope link state
advertisements in this link's link state
database."
::= { hwOspfv3IfEntry 17 }
hwOspfv3IfLinkLsaCksumSum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 32-bit unsigned sum of the Link-Scope link state
advertisements' LS checksums contained in this
link's link state database. The sum can be used
to determine if there has been a change in a
router's link state database, and to compare the
link state database of two routers."
::= { hwOspfv3IfEntry 18 }
hwOspfv3IfPollInterval OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The larger time interval, in seconds, between
the Hello packets sent to an inactive
non-broadcast multi-access neighbor."
DEFVAL { 120 }
::= { hwOspfv3IfEntry 19 }
hwOspfv3IfMulticastForwarding OBJECT-TYPE
SYNTAX INTEGER {
blocked(1), -- no multicast forwarding
multicast(2), -- using multicast address
unicast(3) -- to each OSPFv3 neighbor
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The way multicasts should forwarded on this
interface; not forwarded, forwarded as data
link multicasts, or forwarded as data link
unicasts. Data link multicasting is not
meaningful on point to point and NBMA interfaces,
and setting ospfv3MulticastForwarding to 0
effectively disables all multicast forwarding."
DEFVAL { blocked }
::= { hwOspfv3IfEntry 20 }
-- OSPFv3 Virtual Interface Table
-- The Virtual Interface Table describes the virtual
-- links that the OSPFv3 Process is configured to
-- carry on.
hwOspfv3VirtIfTable OBJECT-TYPE
SYNTAX SEQUENCE OF HwOspfv3VirtIfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about this router's virtual
interfaces."
REFERENCE
"OSPF Version 2, Appendix C.4 Virtual link
parameters"
::= { hwOspfv3Objects 7 }
hwOspfv3VirtIfEntry OBJECT-TYPE
SYNTAX HwOspfv3VirtIfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a single Virtual Interface."
INDEX { hwOspfv3VirtIfAreaId,
hwOspfv3VirtIfNeighbor }
::= { hwOspfv3VirtIfTable 1 }
HwOspfv3VirtIfEntry ::= SEQUENCE {
hwOspfv3VirtIfAreaId
HWOspfv3AreaIdTc,
hwOspfv3VirtIfNeighbor
HWOspfv3RouterIdTc,
hwOspfv3VirtIfIndex
InterfaceIndex,
hwOspfv3VirtIfInstId
HWOspfv3IfInstIdTc,
hwOspfv3VirtIfTransitDelay
HWOspfv3UpToRefreshIntervalTc,
hwOspfv3VirtIfRetransInterval
HWOspfv3UpToRefreshIntervalTc,
hwOspfv3VirtIfHelloInterval
HelloRange,
hwOspfv3VirtIfRtrDeadInterval
HWOspfv3DeadIntRangeTc,
hwOspfv3VirtIfState
INTEGER,
hwOspfv3VirtIfEvents
Counter32,
hwOspfv3VirtIfRowStatus
RowStatus,
hwOspfv3VirtIfLinkScopeLsaCount
Gauge32,
hwOspfv3VirtIfLinkLsaCksumSum
Unsigned32
}
hwOspfv3VirtIfAreaId OBJECT-TYPE
SYNTAX HWOspfv3AreaIdTc
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Transit Area that the Virtual Link
traverses. By definition, this is not
Area 0"
::= { hwOspfv3VirtIfEntry 1 }
hwOspfv3VirtIfNeighbor OBJECT-TYPE
SYNTAX HWOspfv3RouterIdTc
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Router ID of the Virtual Neighbor."
::= { hwOspfv3VirtIfEntry 2 }
hwOspfv3VirtIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local interface index assigned to this
OSPFv3 virtual interface. It is advertised in
Hello's sent over the virtual link and in the
router's router-LSAs."
::= { hwOspfv3VirtIfEntry 3 }
hwOspfv3VirtIfInstId OBJECT-TYPE
SYNTAX HWOspfv3IfInstIdTc
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the interface instance ID to be used
for the virtual interface. This ID has local link
significance only."
::= { hwOspfv3VirtIfEntry 4 }
hwOspfv3VirtIfTransitDelay OBJECT-TYPE
SYNTAX HWOspfv3UpToRefreshIntervalTc
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The estimated number of seconds it takes to
transmit a link state update packet over this
interface."
DEFVAL { 1 }
::= { hwOspfv3VirtIfEntry 5 }
hwOspfv3VirtIfRetransInterval OBJECT-TYPE
SYNTAX HWOspfv3UpToRefreshIntervalTc
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds between link state
advertisement retransmissions, for adjacencies
belonging to this interface. This value is
also used when retransmitting database
description and link state request packets. This
value should be well over the expected
round-trip time."
DEFVAL { 5 }
::= { hwOspfv3VirtIfEntry 6 }
hwOspfv3VirtIfHelloInterval OBJECT-TYPE
SYNTAX HelloRange
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The length of time, in seconds, between the
Hello packets that the router sends on the
interface. This value must be the same for the
virtual neighbor."
DEFVAL { 10 }
::= { hwOspfv3VirtIfEntry 7 }
hwOspfv3VirtIfRtrDeadInterval OBJECT-TYPE
SYNTAX HWOspfv3DeadIntRangeTc
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds that a router's Hello
packets have not been seen before its
neighbors declare the router down. This should
be some multiple of the Hello interval. This
value must be the same for the virtual
neighbor."
DEFVAL { 40 }
::= { hwOspfv3VirtIfEntry 8 }
hwOspfv3VirtIfState OBJECT-TYPE
SYNTAX INTEGER {
down(1),
pointToPoint(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"OSPFv3 virtual interface states. The same encoding
as the hwOspfv3IfTable is used."
::= { hwOspfv3VirtIfEntry 9 }
hwOspfv3VirtIfEvents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of state changes or error events on
this Virtual Link"
::= { hwOspfv3VirtIfEntry 10 }
hwOspfv3VirtIfRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object permits management of the table by
facilitating actions such as row creation,
construction and destruction.
The value of this object has no effect on
whether other objects in this conceptual row can be
modified."
::= { hwOspfv3VirtIfEntry 11 }
hwOspfv3VirtIfLinkScopeLsaCount OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of Link-Scope link state
advertisements in this virtual link's link state
database."
::= { hwOspfv3VirtIfEntry 12 }
hwOspfv3VirtIfLinkLsaCksumSum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 32-bit unsigned sum of the Link-Scope link-state
advertisements' LS checksums contained in this
virtual link's link-state database. The sum can be used
to determine if there has been a change in a
router's link state database, and to compare the
link state database of two routers."
::= { hwOspfv3VirtIfEntry 13 }
-- OSPFv3 Neighbor Table
-- The OSPFv3 Neighbor Table describes all neighbors in
-- the locality of the subject router.
hwOspfv3NbrTable OBJECT-TYPE
SYNTAX SEQUENCE OF HwOspfv3NbrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of non-virtual neighbor information."
REFERENCE
"OSPF Version 2, Section 10 The Neighbor Data
Structure"
::= { hwOspfv3Objects 8 }
hwOspfv3NbrEntry OBJECT-TYPE
SYNTAX HwOspfv3NbrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The information regarding a single neighbor."
REFERENCE
"OSPF Version 2, Section 10 The Neighbor Data
Structure"
INDEX { hwOspfv3NbrIfIndex,
hwOspfv3NbrIfInstId,
hwOspfv3NbrRtrId }
::= { hwOspfv3NbrTable 1 }
HwOspfv3NbrEntry ::= SEQUENCE {
hwOspfv3NbrIfIndex
InterfaceIndex,
hwOspfv3NbrIfInstId
HWOspfv3IfInstIdTc,
hwOspfv3NbrRtrId
HWOspfv3RouterIdTc,
hwOspfv3NbrAddressType
InetAddressType,
hwOspfv3NbrAddress
InetAddress,
hwOspfv3NbrOptions
Integer32,
hwOspfv3NbrPriority
DesignatedRouterPriority,
hwOspfv3NbrState
INTEGER,
hwOspfv3NbrEvents
Counter32,
hwOspfv3NbrLsRetransQLen
Gauge32,
hwOspfv3NbrHelloSuppressed
TruthValue,
hwOspfv3NbrIfId
InterfaceIndex,
hwOspfv3NbrRestartHelperStatus
INTEGER,
hwOspfv3NbrRestartHelperAge
HWOspfv3UpToRefreshIntervalTc,
hwOspfv3NbrRestartHelperExitRc
INTEGER
}
hwOspfv3NbrIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The local link ID of the link over which the
neighbor can be reached."
::= { hwOspfv3NbrEntry 1 }
hwOspfv3NbrIfInstId OBJECT-TYPE
SYNTAX HWOspfv3IfInstIdTc
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Interface instance over which the neighbor
can be reached. This ID has local link
significance only."
::= { hwOspfv3NbrEntry 2 }
hwOspfv3NbrRtrId OBJECT-TYPE
SYNTAX HWOspfv3RouterIdTc
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A 32-bit integer uniquely identifying the neighboring
router in the Autonomous System."
::= { hwOspfv3NbrEntry 3 }
hwOspfv3NbrAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address type of ospfv3NbrAddress. Only IPv6
addresses without zone index are expected."
::= { hwOspfv3NbrEntry 4 }
hwOspfv3NbrAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IPv6 address of the neighbor associated with
the local link."
::= { hwOspfv3NbrEntry 5 }
hwOspfv3NbrOptions OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A Bit Mask corresponding to the neighbor's
options field."
REFERENCE
"OSPF Version 3, Appendix A.2 the Options field"
::= { hwOspfv3NbrEntry 6 }
hwOspfv3NbrPriority OBJECT-TYPE
SYNTAX DesignatedRouterPriority
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The priority of this neighbor in the designated
router election algorithm. The value 0 signifies
that the neighbor is not eligible to become the
designated router on this particular network."
::= { hwOspfv3NbrEntry 7 }
hwOspfv3NbrState OBJECT-TYPE
SYNTAX INTEGER {
down(1),
attempt(2),
init(3),
twoWay(4),
exchangeStart(5),
exchange(6),
loading(7),
full(8)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The State of the relationship with this
Neighbor."
REFERENCE
"OSPF Version 2, Section 10.1 Neighbor States"
::= { hwOspfv3NbrEntry 8 }
hwOspfv3NbrEvents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times this neighbor relationship
has changed state, or an error has occurred."
::= { hwOspfv3NbrEntry 9 }
hwOspfv3NbrLsRetransQLen OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current length of the retransmission
queue."
::= { hwOspfv3NbrEntry 10 }
hwOspfv3NbrHelloSuppressed OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether Hellos are being suppressed
to the neighbor"
::= { hwOspfv3NbrEntry 11 }
hwOspfv3NbrIfId OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The interface ID that the neighbor advertises
in its Hello Packets on this link, that is, the
neighbor's local interface index."
::= { hwOspfv3NbrEntry 12 }
hwOspfv3NbrRestartHelperStatus OBJECT-TYPE
SYNTAX INTEGER { notHelping (1),
helping (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether the router is acting
as a Graceful restart helper for the neighbor."
::= { hwOspfv3NbrEntry 13 }
hwOspfv3NbrRestartHelperAge OBJECT-TYPE
SYNTAX HWOspfv3UpToRefreshIntervalTc
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Remaining time in current OSPFv3 Graceful restart
interval, if the router is acting as a restart
helper for the neighbor."
::= { hwOspfv3NbrEntry 14 }
hwOspfv3NbrRestartHelperExitRc OBJECT-TYPE
SYNTAX INTEGER { none (1),
inProgress (2),
completed (3),
timedOut (4),
topologyChanged (5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Describes the outcome of the last attempt at acting
as a Graceful restart helper for the neighbor.
none:............no restart has yet been attempted.
inProgress:......a restart attempt is currently underway.
completed:.......the last restart completed successfully.
timedOut:........the last restart timed out.
topologyChanged:.the last restart was aborted due to
a topology change."
::= { hwOspfv3NbrEntry 15 }
-- OSPFv3 Configured Neighbor Table
-- The OSPFv3 Configured Neighbor Table describes all configured
-- neighbors
hwOspfv3CfgNbrTable OBJECT-TYPE
SYNTAX SEQUENCE OF HwOspfv3CfgNbrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of configured, non-virtual neighbor
information."
REFERENCE
"OSPF Version 2, Section 10 The Neighbor Data
Structure"
::= { hwOspfv3Objects 9 }
hwOspfv3CfgNbrEntry OBJECT-TYPE
SYNTAX HwOspfv3CfgNbrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The information regarding a single configured
neighbor or neighbor discovered by lower-level
protocols such as Inverse Neighbor Discovery."
REFERENCE
"OSPF Version 2, Section 10 The Neighbor Data
Structure"
INDEX { hwOspfv3CfgNbrIfIndex,
hwOspfv3CfgNbrIfInstId,
hwOspfv3CfgNbrRtrId }
::= { hwOspfv3CfgNbrTable 1 }
HwOspfv3CfgNbrEntry ::= SEQUENCE {
hwOspfv3CfgNbrIfIndex
InterfaceIndex,
hwOspfv3CfgNbrIfInstId
HWOspfv3IfInstIdTc,
hwOspfv3CfgNbrRtrId
HWOspfv3RouterIdTc,
hwOspfv3CfgNbrPriority
DesignatedRouterPriority,
hwOspfv3CfgNbrRowStatus
RowStatus
}
hwOspfv3CfgNbrIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The local link ID of the link over which the
neighbor can be reached."
::= { hwOspfv3CfgNbrEntry 1 }
hwOspfv3CfgNbrIfInstId OBJECT-TYPE
SYNTAX HWOspfv3IfInstIdTc
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Interface instance over which the neighbor
can be reached. This ID has local link
significance only."
::= { hwOspfv3CfgNbrEntry 2 }
hwOspfv3CfgNbrRtrId OBJECT-TYPE
SYNTAX HWOspfv3RouterIdTc
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A 32-bit integer uniquely identifying the static neighbor
router in the Autonomous System."
::= { hwOspfv3CfgNbrEntry 3 }
hwOspfv3CfgNbrPriority OBJECT-TYPE
SYNTAX DesignatedRouterPriority
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The priority of this neighbor in the designated
router election algorithm. The value 0 signifies
that the neighbor is not eligible to become the
designated router on this particular network."
DEFVAL { 1 }
::= { hwOspfv3CfgNbrEntry 4 }
hwOspfv3CfgNbrRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object permits management of the table by
facilitating actions such as row creation,
construction and destruction.
The value of this object has no effect on
whether other objects in this conceptual row can be
modified."
::= { hwOspfv3CfgNbrEntry 5 }
-- OSPFv3 Virtual Neighbor Table
-- This table describes all virtual neighbors.
-- Since Virtual Links are configured in the
-- virtual interface table, this table is read-only.
hwOspfv3VirtNbrTable OBJECT-TYPE
SYNTAX SEQUENCE OF HwOspfv3VirtNbrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of virtual neighbor information."
REFERENCE
"OSPF Version 2, Section 15 Virtual Links"
::= { hwOspfv3Objects 10 }
hwOspfv3VirtNbrEntry OBJECT-TYPE
SYNTAX HwOspfv3VirtNbrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Virtual neighbor information."
INDEX { hwOspfv3VirtNbrArea,
hwOspfv3VirtNbrRtrId }
::= { hwOspfv3VirtNbrTable 1 }
HwOspfv3VirtNbrEntry ::= SEQUENCE {
hwOspfv3VirtNbrArea
HWOspfv3AreaIdTc,
hwOspfv3VirtNbrRtrId
HWOspfv3RouterIdTc,
hwOspfv3VirtNbrIfIndex
InterfaceIndex,
hwOspfv3VirtNbrIfInstId
HWOspfv3IfInstIdTc,
hwOspfv3VirtNbrAddressType
InetAddressType,
hwOspfv3VirtNbrAddress
InetAddress,
hwOspfv3VirtNbrOptions
Integer32,
hwOspfv3VirtNbrState
INTEGER,
hwOspfv3VirtNbrEvents
Counter32,
hwOspfv3VirtNbrLsRetransQLen
Gauge32,
hwOspfv3VirtNbrHelloSuppressed
TruthValue,
hwOspfv3VirtNbrIfId
InterfaceIndex,
hwOspfv3VirtNbrRestartHelperStatus
INTEGER,
hwOspfv3VirtNbrRestartHelperAge
HWOspfv3UpToRefreshIntervalTc,
hwOspfv3VirtNbrRestartHelperExitRc
INTEGER
}
hwOspfv3VirtNbrArea OBJECT-TYPE
SYNTAX HWOspfv3AreaIdTc
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Transit Area Identifier."
::= { hwOspfv3VirtNbrEntry 1 }
hwOspfv3VirtNbrRtrId OBJECT-TYPE
SYNTAX HWOspfv3RouterIdTc
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A 32-bit integer uniquely identifying the
neighboring router in the Autonomous System."
::= { hwOspfv3VirtNbrEntry 2 }
hwOspfv3VirtNbrIfIndex OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local interface ID for the virtual link over
which the neighbor can be reached."
::= { hwOspfv3VirtNbrEntry 3 }
hwOspfv3VirtNbrIfInstId OBJECT-TYPE
SYNTAX HWOspfv3IfInstIdTc
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The interface instance for the virtual link over
which the neighbor can be reached."
::= { hwOspfv3VirtNbrEntry 4 }
hwOspfv3VirtNbrAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address type of ospfv3VirtNbrAddress. Only IPv6
addresses without zone index are expected."
::= { hwOspfv3VirtNbrEntry 5 }
hwOspfv3VirtNbrAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The IPv6 address advertised by this Virtual Neighbor.
It must be a Global scope address."
::= { hwOspfv3VirtNbrEntry 6 }
hwOspfv3VirtNbrOptions OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A Bit Mask corresponding to the neighbor's options
field."
REFERENCE
"OSPF Version 3, Appendix A.2 the Options field"
::= { hwOspfv3VirtNbrEntry 7 }
hwOspfv3VirtNbrState OBJECT-TYPE
SYNTAX INTEGER {
down(1),
attempt(2),
init(3),
twoWay(4),
exchangeStart(5),
exchange(6),
loading(7),
full(8)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state of the Virtual Neighbor Relationship."
::= { hwOspfv3VirtNbrEntry 8 }
hwOspfv3VirtNbrEvents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times this virtual link has
changed its state, or an error has occurred."
::= { hwOspfv3VirtNbrEntry 9 }
hwOspfv3VirtNbrLsRetransQLen OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current length of the retransmission
queue."
::= { hwOspfv3VirtNbrEntry 10 }
hwOspfv3VirtNbrHelloSuppressed OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether Hellos are being suppressed
to the neighbor"
::= { hwOspfv3VirtNbrEntry 11 }
hwOspfv3VirtNbrIfId OBJECT-TYPE
SYNTAX InterfaceIndex
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The interface ID that the neighbor advertises
in its Hello Packets on this virtual link, that is,
the neighbor's local interface ID."
::= { hwOspfv3VirtNbrEntry 12 }
hwOspfv3VirtNbrRestartHelperStatus OBJECT-TYPE
SYNTAX INTEGER { notHelping (1),
helping (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether the router is acting
as a Graceful restart helper for the neighbor."
::= { hwOspfv3VirtNbrEntry 13 }
hwOspfv3VirtNbrRestartHelperAge OBJECT-TYPE
SYNTAX HWOspfv3UpToRefreshIntervalTc
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Remaining time in current OSPFv3 Graceful restart
interval, if the router is acting as a restart
helper for the neighbor."
::= { hwOspfv3VirtNbrEntry 14 }
hwOspfv3VirtNbrRestartHelperExitRc OBJECT-TYPE
SYNTAX INTEGER { none (1),
inProgress (2),
completed (3),
timedOut (4),
topologyChanged (5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Describes the outcome of the last attempt at acting
as a Graceful restart helper for the neighbor.
none:............no restart has yet been attempted.
inProgress:......a restart attempt is currently underway.
completed:.......the last restart completed successfully.
timedOut:........the last restart timed out.
topologyChanged:.the last restart was aborted due to
a topology change."
::= { hwOspfv3VirtNbrEntry 15 }
--
-- The OSPFv3 Area Aggregate Table
--
hwOspfv3AreaAggregateTable OBJECT-TYPE
SYNTAX SEQUENCE OF HwOspfv3AreaAggregateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A range of IPv6 prefixes specified by a
prefix/prefix length pair. Note that if
ranges are configured such that one range
subsumes another range the most specific
match is the preferred one."
::= { hwOspfv3Objects 11 }
hwOspfv3AreaAggregateEntry OBJECT-TYPE
SYNTAX HwOspfv3AreaAggregateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A range of IPv6 prefixes specified by a
prefix/prefix length pair. Note that if
ranges are configured such that one range
subsumes another range the most specific match is
the preferred one."
REFERENCE
"OSPF Version 2, Appendix C.2 Area parameters"
INDEX { hwOspfv3AreaAggregateAreaId,
hwOspfv3AreaAggregateAreaLsdbType,
hwOspfv3AreaAggregatePrefixType,
hwOspfv3AreaAggregatePrefix,
hwOspfv3AreaAggregatePrefixLength }
::= { hwOspfv3AreaAggregateTable 1 }
HwOspfv3AreaAggregateEntry ::= SEQUENCE {
hwOspfv3AreaAggregateAreaId
HWOspfv3AreaIdTc,
hwOspfv3AreaAggregateAreaLsdbType
INTEGER,
hwOspfv3AreaAggregatePrefixType
InetAddressType,
hwOspfv3AreaAggregatePrefix
InetAddress,
hwOspfv3AreaAggregatePrefixLength
InetAddressPrefixLength,
hwOspfv3AreaAggregateRowStatus
RowStatus,
hwOspfv3AreaAggregateEffect
INTEGER
}
hwOspfv3AreaAggregateAreaId OBJECT-TYPE
SYNTAX HWOspfv3AreaIdTc
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Area the Address Aggregate is to be found
within."
REFERENCE
"OSPF Version 2, Appendix C.2 Area parameters"
::= { hwOspfv3AreaAggregateEntry 1 }
hwOspfv3AreaAggregateAreaLsdbType OBJECT-TYPE
SYNTAX INTEGER {
interAreaPrefixLsa(8195), -- 0x2003
nssaExternalLsa(8199) -- 0x2007
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The type of the Address Aggregate. This field
specifies the Area Lsdb type that this Address
Aggregate applies to."
REFERENCE
"OSPF Version 2, Appendix A.4.1 The Link State
Advertisement header"
::= { hwOspfv3AreaAggregateEntry 2 }
hwOspfv3AreaAggregatePrefixType OBJECT-TYPE
SYNTAX InetAddressType --{ ipv6(2) }
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The prefix type of ospfv3AreaAggregatePrefix. Only
IPv6 addresses are expected."
::= { hwOspfv3AreaAggregateEntry 4 }
hwOspfv3AreaAggregatePrefix OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IPv6 Prefix."
REFERENCE
"OSPF Version 2, Appendix C.2 Area parameters"
::= { hwOspfv3AreaAggregateEntry 5 }
hwOspfv3AreaAggregatePrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength (1..128)
UNITS "bits"
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The length of the prefix (in bits). A prefix can
not be shorter than 0 bits."
REFERENCE
"OSPF Version 2, Appendix C.2 Area parameters"
::= { hwOspfv3AreaAggregateEntry 6 }
hwOspfv3AreaAggregateRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object permits management of the table by
facilitating actions such as row creation,
construction and destruction.
The value of this object has no effect on
whether other objects in this conceptual row can be
modified."
::= { hwOspfv3AreaAggregateEntry 7 }
hwOspfv3AreaAggregateEffect OBJECT-TYPE
SYNTAX INTEGER {
advertiseMatching(1),
doNotAdvertiseMatching(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Prefixes subsumed by ranges either trigger the
advertisement of the indicated aggregate
(advertiseMatching), or result in the prefix not
being advertised at all outside the area."
DEFVAL { advertiseMatching }
::= { hwOspfv3AreaAggregateEntry 8 }
-- The Ospfv3 Notification Table
-- The Ospfv3 Notification Table records fields that are
-- required for notifications
hwOspfv3NotificationEntry OBJECT IDENTIFIER
::= { hwOspfv3Objects 12 }
hwOspfv3ConfigErrorType OBJECT-TYPE
SYNTAX INTEGER {
badVersion (1),
areaMismatch (2),
unknownNbmaNbr (3), -- Router is DR eligible
unknownVirtualNbr (4),
helloIntervalMismatch (5),
deadIntervalMismatch (6),
optionMismatch (7),
mtuMismatch (8),
duplicateRouterId (9),
noError (10) }
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Potential types of configuration conflicts.
Used by the ospfv3ConfigError and
ospfv3ConfigVirtError notifications. When the last value
of a notification using this object is needed, but no
notifications of that type have been sent, this value
pertaining to this object should be returned as
noError"
::= { hwOspfv3NotificationEntry 1 }
hwOspfv3PacketType OBJECT-TYPE
SYNTAX INTEGER {
hello (1),
dbDescript (2),
lsReq (3),
lsUpdate (4),
lsAck (5),
nullPacket (6) }
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"OSPFv3 packet types. When the last value of a notification
using this object is needed, but no notifications of
that type have been sent, the value pertaining
to this object should be returned as nullPacket"
::= { hwOspfv3NotificationEntry 2 }
hwOspfv3PacketSrc OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The IPv6 address of an inbound packet that cannot
be identified by a neighbor instance. When
the last value of a notification using this object is
needed, but no notifications of that type have been sent,
the value pertaining to this object should
be returned as 0.
Only IPv6 addresses without zone index are expected."
::= { hwOspfv3NotificationEntry 3 }
hwOspfv3IfName OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1..64))
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"The interface name"
::= { hwOspfv3NotificationEntry 4 }
hwOspfv3IfStateChgReason OBJECT-TYPE
SYNTAX INTEGER {
noEvent(1),
interfaceUp(2),
waitTimerExpired(3),
backupSeenOccured(4),
neighborChangeEventOccured(5),
loopInd(6),
unloopInd(7),
interfaceDown(8)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Interface state change reason."
::= { hwOspfv3NotificationEntry 5 }
hwOspfv3NbrStateChgReason OBJECT-TYPE
SYNTAX INTEGER {
noEvent(1),
receivedHelloPacket(2),
start(3),
receivedTwoWay(4),
negotiationDone(5),
exchangeDone(6),
receivedBadLSRequest(7),
loadingDone(8),
establishedAdjacency(9),
mismatchInSeqNumber(10),
receivedOneWay(11),
nbrKilled(12),
inactivityTimerExpired(13),
linkDown(14)
}
MAX-ACCESS accessible-for-notify
STATUS current
DESCRIPTION
"Neighbor state change reason."
::= { hwOspfv3NotificationEntry 6 }
-- Notification definitions
hwOspfv3VirtIfStateChange NOTIFICATION-TYPE
OBJECTS { hwOspfv3RouterId, -- The originator of the notification
hwOspfv3VirtIfState, -- The new state
hwOspfv3IfStateChgReason -- The interface state change reason
}
STATUS current
DESCRIPTION
"An ospfv3VirtIfStateChange notification signifies that there
has been a change in the state of an OSPFv3 virtual
interface.
This notification should be generated when the interface
state regresses (e.g., goes from Point-to-Point to Down)
or progresses to a terminal state (i.e., Point-to-Point)."
::= { hwOspfv3Notifications 1 }
hwOspfv3NbrStateChange NOTIFICATION-TYPE
OBJECTS { hwOspfv3RouterId, -- The originator of the notification
hwOspfv3NbrState, -- The new state
hwOspfv3IfName, -- The interface name
hwOspfv3NbrStateChgReason -- The neighbor state change reason
}
STATUS current
DESCRIPTION
"An ospfv3NbrStateChange notification signifies that
there has been a change in the state of a
non-virtual OSPFv3 neighbor. This notification should be
generated when the neighbor state regresses
(e.g., goes from Attempt or Full to 1-Way or
Down) or progresses to a terminal state (e.g.,
2-Way or Full). When an neighbor transitions
from or to Full on non-broadcast multi-access
and broadcast networks, the notification should be
generated by the designated router. A designated
router transitioning to Down will be noted by
ospfIfStateChange."
::= { hwOspfv3Notifications 2 }
hwOspfv3VirtNbrStateChange NOTIFICATION-TYPE
OBJECTS { hwOspfv3RouterId, -- The originator of the notification
hwOspfv3VirtNbrState, -- The new state
hwOspfv3NbrStateChgReason -- The neighbor state change reason
}
STATUS current
DESCRIPTION
"An ospfv3VirtNbrStateChange notification signifies
that there has been a change in the state of an OSPFv3
virtual neighbor. This notification should be generated
when the neighbor state regresses (e.g., goes
from Attempt or Full to 1-Way or Down) or
progresses to a terminal state (e.g., Full)."
::= { hwOspfv3Notifications 3 }
hwOspfv3IfConfigError NOTIFICATION-TYPE
OBJECTS { hwOspfv3RouterId, -- The originator of the notification
hwOspfv3IfState, -- State of the interface
hwOspfv3PacketSrc, -- IPv6 address of source
hwOspfv3ConfigErrorType, -- Type of error
hwOspfv3PacketType -- Type of packet
}
STATUS current
DESCRIPTION
"An ospfv3IfConfigError notification signifies that a
packet has been received on a non-virtual
interface from a router whose configuration
parameters conflict with this router's
configuration parameters. Note that the event
optionMismatch should cause a notification only if it
prevents an adjacency from forming."
::= { hwOspfv3Notifications 4 }
hwOspfv3VirtIfConfigError NOTIFICATION-TYPE
OBJECTS { hwOspfv3RouterId, -- The originator of the notification
hwOspfv3VirtIfState, -- State of the interface
hwOspfv3ConfigErrorType, -- Type of error
hwOspfv3PacketType
}
STATUS current
DESCRIPTION
"An ospfv3VirtIfConfigError notification signifies that a
packet has been received on a virtual interface
from a router whose configuration parameters
conflict with this router's configuration
parameters. Note that the event optionMismatch
should cause a notification only if it prevents an
adjacency from forming."
::= { hwOspfv3Notifications 5 }
hwOspfv3IfRxBadPacket NOTIFICATION-TYPE
OBJECTS { hwOspfv3RouterId, -- The originator of the notification
hwOspfv3IfState, -- State of the interface
hwOspfv3PacketSrc, -- The source IPv6 address
hwOspfv3PacketType -- Type of packet
}
STATUS current
DESCRIPTION
"An ospfv3IfRxBadPacket notification signifies that an
OSPFv3 packet that cannot be parsed has been received on a
non-virtual interface."
::= { hwOspfv3Notifications 6 }
hwOspfv3VirtIfRxBadPacket NOTIFICATION-TYPE
OBJECTS { hwOspfv3RouterId, -- The originator of the notification
hwOspfv3VirtIfState, -- State of the interface
hwOspfv3PacketType -- Type of packet
}
STATUS current
DESCRIPTION
"An ospfv3VirtIfRxBadPacket notification signifies
that an OSPFv3 packet that cannot be parsed has been received
on a virtual interface."
::= { hwOspfv3Notifications 7 }
hwOspfv3IfStateChange NOTIFICATION-TYPE
OBJECTS { hwOspfv3RouterId, -- The originator of the notification
hwOspfv3IfState, -- The new state
hwOspfv3IfName, -- The interface name
hwOspfv3IfStateChgReason -- The interface state change reason
}
STATUS current
DESCRIPTION
"An ospfv3IfStateChange notification signifies that there
has been a change in the state of a non-virtual
OSPFv3 interface. This notification should be generated
when the interface state regresses (e.g., goes
from Dr to Down) or progresses to a terminal
state (i.e., Point-to-Point, DR Other, Dr, or
Backup)."
::= { hwOspfv3Notifications 8 }
hwOspfv3RestartStatusChange NOTIFICATION-TYPE
OBJECTS { hwOspfv3RouterId, -- The originator of the notification
hwOspfv3RestartStatus, -- new status
hwOspfv3RestartInterval,
hwOspfv3RestartExitRc
}
STATUS current
DESCRIPTION
"An ospfv3RestartStatusChange notification signifies that
there has been a change in the graceful restart
state for the router. This notification should be
generated when the router restart status
changes."
::= { hwOspfv3Notifications 9 }
hwOspfv3NbrRestartHelperStatusChange NOTIFICATION-TYPE
OBJECTS { hwOspfv3RouterId, -- The originator of the notification
hwOspfv3NbrRestartHelperStatus, -- new status
hwOspfv3NbrRestartHelperAge,
hwOspfv3NbrRestartHelperExitRc
}
STATUS current
DESCRIPTION
"An ospfv3NbrRestartHelperStatusChange notification
signifies that there has been a change in the
graceful restart helper state for the neighbor.
This notification should be generated when the
neighbor restart helper status transitions for a neighbor."
::= { hwOspfv3Notifications 10 }
hwOspfv3VirtNbrRestartHelperStatusChange NOTIFICATION-TYPE
OBJECTS { hwOspfv3RouterId, -- The originator of the notification
hwOspfv3VirtNbrRestartHelperStatus, -- new status
hwOspfv3VirtNbrRestartHelperAge,
hwOspfv3VirtNbrRestartHelperExitRc
}
STATUS current
DESCRIPTION
"An ospfv3VirtNbrRestartHelperStatusChange
notification signifies that there has been a
change in the graceful restart helper state for
the virtual neighbor. This notification should be
generated when the virtual neighbor restart helper status
transitions for a virtual neighbor."
::= { hwOspfv3Notifications 11 }
hwOspfv3NssaTranslatorStatusChange NOTIFICATION-TYPE
OBJECTS { hwOspfv3RouterId, -- The originator of the notification
hwOspfv3AreaNssaTranslatorState -- new status
}
STATUS current
DESCRIPTION
"An ospfv3NssaTranslatorStatusChange notification
indicates that there has been a change in the router's ability
to translate OSPFv3 NSSA LSAs into OSPFv3 External LSAs.
This notification should be generated when the Translator Status
transitions from or to any defined status on a per area basis."
::= { hwOspfv3Notifications 12 }
-- conformance information
hwOspfv3Groups OBJECT IDENTIFIER ::= { hwOspfv3Conformance 1 }
hwOspfv3Compliances OBJECT IDENTIFIER ::= { hwOspfv3Conformance 2 }
-- compliance statements
hwOspfv3Compliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION "The compliance statement"
MODULE -- this module
MANDATORY-GROUPS {
hwOspfv3BasicGroup,
hwOspfv3AreaGroup,
hwOspfv3IfGroup,
hwOspfv3VirtIfGroup,
hwOspfv3NbrGroup,
hwOspfv3CfgNbrGroup,
hwOspfv3VirtNbrGroup,
hwOspfv3AreaAggregateGroup
}
GROUP hwOspfv3AsLsdbGroup
DESCRIPTION
"This group is required for OSPFv3 systems that
display their AS-scope link state database."
GROUP hwOspfv3AreaLsdbGroup
DESCRIPTION
"This group is required for OSPFv3 systems that
display their Area-scope link state database."
GROUP hwOspfv3LinkLsdbGroup
DESCRIPTION
"This group is required for OSPFv3 systems that
display their Link-scope link state database."
GROUP hwOspfv3NotificationObjectGroup
DESCRIPTION
"This group is required for OSPFv3 systems that
support OSPFv3 notifications."
GROUP hwOspfv3NotificationGroup
DESCRIPTION
"This group is required for OSPFv3 systems that
support OSPFv3 notifications."
OBJECT hwOspfv3NbrAddressType
SYNTAX InetAddressType -- { ipv6(2) }
DESCRIPTION
"An implementation is only required to support IPv6
address without zone index."
OBJECT hwOspfv3NbrAddress
SYNTAX InetAddress (SIZE (16))
DESCRIPTION
"An implementation is only required to support IPv6
address without zone index."
OBJECT hwOspfv3VirtNbrAddressType
SYNTAX InetAddressType --{ ipv6(2) }
DESCRIPTION
"An implementation is only required to support IPv6
address without zone index."
OBJECT hwOspfv3VirtNbrAddress
SYNTAX InetAddress (SIZE (16))
DESCRIPTION
"An implementation is only required to support IPv6
address without zone index."
::= { hwOspfv3Compliances 1 }
hwOspfv3ReadOnlyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"When this MIB module is implemented without
support for read-create (i.e., in read-only
mode), the implementation can claim read-only
compliance. Such a device can then be monitored,
but cannot be configured with this MIB."
MODULE -- this module
MANDATORY-GROUPS {
hwOspfv3BasicGroup,
hwOspfv3AreaGroup,
hwOspfv3IfGroup,
hwOspfv3VirtIfGroup,
hwOspfv3NbrGroup,
hwOspfv3CfgNbrGroup,
hwOspfv3VirtNbrGroup,
hwOspfv3AreaAggregateGroup
}
GROUP hwOspfv3AsLsdbGroup
DESCRIPTION
"This group is required for OSPFv3 systems that
display their AS-scope link state database."
GROUP hwOspfv3AreaLsdbGroup
DESCRIPTION
"This group is required for OSPFv3 systems that
display their Area-scope link state database."
GROUP hwOspfv3LinkLsdbGroup
DESCRIPTION
"This group is required for OSPFv3 systems that
display their Link-scope link state database
for non-virtual interfaces."
GROUP hwOspfv3NotificationObjectGroup
DESCRIPTION
"This group is required for OSPFv3 systems that
support OSPFv3 notifications."
GROUP hwOspfv3NotificationGroup
DESCRIPTION
"This group is required for OSPFv3 systems that
support OSPFv3 notifications."
OBJECT hwOspfv3RouterId
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3AdminStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3ExtAreaLsdbLimit
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3ReferenceBandwidth
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3RestartSupport
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3RestartInterval
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3NotificationEnable
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3AreaSummary
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3AreaRowStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3AreaStubMetric
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3AreaNssaTranslatorRole
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3AreaNssaTranslatorStabInterval
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3IfAreaId
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3IfType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3IfAdminStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3IfRtrPriority
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3IfTransitDelay
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3IfRetransInterval
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3IfHelloInterval
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3IfRtrDeadInterval
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3IfPollInterval
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3IfRowStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3IfMetricValue
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3VirtIfTransitDelay
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3VirtIfRetransInterval
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3VirtIfHelloInterval
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3VirtIfRtrDeadInterval
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3VirtIfRowStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3CfgNbrPriority
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3CfgNbrRowStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3AreaAggregateRowStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT hwOspfv3AreaAggregateEffect
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { hwOspfv3Compliances 2 }
-- units of conformance
hwOspfv3BasicGroup OBJECT-GROUP
OBJECTS {
hwOspfv3RouterId,
hwOspfv3AdminStatus,
hwOspfv3VersionNumber,
hwOspfv3AreaBdrRtrStatus,
hwOspfv3AsBdrRtrStatus,
hwOspfv3AsScopeLsaCount,
hwOspfv3AsScopeLsaCksumSum,
hwOspfv3OriginateNewLsas,
hwOspfv3RxNewLsas,
hwOspfv3ExtLsaCount,
hwOspfv3ExtAreaLsdbLimit,
hwOspfv3RestartSupport,
hwOspfv3RestartInterval,
hwOspfv3RestartStatus,
hwOspfv3RestartAge,
hwOspfv3RestartExitRc,
hwOspfv3NotificationEnable,
hwOspfv3ReferenceBandwidth
}
STATUS current
DESCRIPTION
"These objects are used for managing/monitoring
OSPFv3 global parameters."
::= { hwOspfv3Groups 1 }
hwOspfv3AreaGroup OBJECT-GROUP
OBJECTS {
hwOspfv3AreaImportAsExtern,
hwOspfv3AreaSpfRuns,
hwOspfv3AreaBdrRtrCount,
hwOspfv3AreaAsBdrRtrCount,
hwOspfv3AreaScopeLsaCount,
hwOspfv3AreaScopeLsaCksumSum,
hwOspfv3AreaSummary,
hwOspfv3AreaRowStatus,
hwOspfv3AreaStubMetric,
hwOspfv3AreaNssaTranslatorRole,
hwOspfv3AreaNssaTranslatorState,
hwOspfv3AreaNssaTranslatorStabInterval,
hwOspfv3AreaNssaTranslatorEvents
}
STATUS current
DESCRIPTION
"These objects are used for OSPFv3 systems
supporting areas."
::= { hwOspfv3Groups 2 }
hwOspfv3AsLsdbGroup OBJECT-GROUP
OBJECTS {
hwOspfv3AsLsdbSequence,
hwOspfv3AsLsdbAge,
hwOspfv3AsLsdbChecksum,
hwOspfv3AsLsdbAdvertisement,
hwOspfv3AsLsdbTypeKnown
}
STATUS current
DESCRIPTION
"These objects are used for OSPFv3 systems
that display their AS-scope link state database."
::= { hwOspfv3Groups 3 }
hwOspfv3AreaLsdbGroup OBJECT-GROUP
OBJECTS {
hwOspfv3AreaLsdbSequence,
hwOspfv3AreaLsdbAge,
hwOspfv3AreaLsdbChecksum,
hwOspfv3AreaLsdbAdvertisement,
hwOspfv3AreaLsdbTypeKnown
}
STATUS current
DESCRIPTION
"These objects are used for OSPFv3 systems
that display their Area-scope link state database."
::= { hwOspfv3Groups 4 }
hwOspfv3LinkLsdbGroup OBJECT-GROUP
OBJECTS {
hwOspfv3LinkLsdbSequence,
hwOspfv3LinkLsdbAge,
hwOspfv3LinkLsdbChecksum,
hwOspfv3LinkLsdbAdvertisement,
hwOspfv3LinkLsdbTypeKnown
}
STATUS current
DESCRIPTION
"These objects are used for OSPFv3 systems
that display their Link-scope link state database."
::= { hwOspfv3Groups 5 }
hwOspfv3IfGroup OBJECT-GROUP
OBJECTS {
hwOspfv3IfAreaId,
hwOspfv3IfType,
hwOspfv3IfAdminStatus,
hwOspfv3IfRtrPriority,
hwOspfv3IfTransitDelay,
hwOspfv3IfRetransInterval,
hwOspfv3IfHelloInterval,
hwOspfv3IfRtrDeadInterval,
hwOspfv3IfState,
hwOspfv3IfDesignatedRouter,
hwOspfv3IfBackupDesignatedRouter,
hwOspfv3IfEvents,
hwOspfv3IfRowStatus,
hwOspfv3IfMetricValue,
hwOspfv3IfLinkScopeLsaCount,
hwOspfv3IfLinkLsaCksumSum,
hwOspfv3IfPollInterval,
hwOspfv3IfMulticastForwarding
}
STATUS current
DESCRIPTION
"These interface objects used for
managing/monitoring OSPFv3 interfaces."
::= { hwOspfv3Groups 6 }
hwOspfv3VirtIfGroup OBJECT-GROUP
OBJECTS {
hwOspfv3VirtIfIndex,
hwOspfv3VirtIfInstId,
hwOspfv3VirtIfTransitDelay,
hwOspfv3VirtIfRetransInterval,
hwOspfv3VirtIfHelloInterval,
hwOspfv3VirtIfRtrDeadInterval,
hwOspfv3VirtIfState,
hwOspfv3VirtIfEvents,
hwOspfv3VirtIfRowStatus,
hwOspfv3VirtIfLinkScopeLsaCount,
hwOspfv3VirtIfLinkLsaCksumSum
}
STATUS current
DESCRIPTION
"These virtual interface objects are used for
managing/monitoring OSPFv3 virtual interfaces."
::= { hwOspfv3Groups 7 }
hwOspfv3NbrGroup OBJECT-GROUP
OBJECTS {
hwOspfv3NbrAddressType,
hwOspfv3NbrAddress,
hwOspfv3NbrOptions,
hwOspfv3NbrPriority,
hwOspfv3NbrState,
hwOspfv3NbrEvents,
hwOspfv3NbrLsRetransQLen,
hwOspfv3NbrHelloSuppressed,
hwOspfv3NbrIfId,
hwOspfv3NbrRestartHelperStatus,
hwOspfv3NbrRestartHelperAge,
hwOspfv3NbrRestartHelperExitRc
}
STATUS current
DESCRIPTION
"These neighbor objects are used for
managing/monitoring OSPFv3 neighbors."
::= { hwOspfv3Groups 8 }
hwOspfv3CfgNbrGroup OBJECT-GROUP
OBJECTS {
hwOspfv3CfgNbrPriority,
hwOspfv3CfgNbrRowStatus
}
STATUS current
DESCRIPTION
"These configured neighbor objects are used for
managing/monitoring OSPFv3 configured neighbors."
::= { hwOspfv3Groups 9 }
hwOspfv3VirtNbrGroup OBJECT-GROUP
OBJECTS {
hwOspfv3VirtNbrIfIndex,
hwOspfv3VirtNbrIfInstId,
hwOspfv3VirtNbrAddressType,
hwOspfv3VirtNbrAddress,
hwOspfv3VirtNbrOptions,
hwOspfv3VirtNbrState,
hwOspfv3VirtNbrEvents,
hwOspfv3VirtNbrLsRetransQLen,
hwOspfv3VirtNbrHelloSuppressed,
hwOspfv3VirtNbrIfId,
hwOspfv3VirtNbrRestartHelperStatus,
hwOspfv3VirtNbrRestartHelperAge,
hwOspfv3VirtNbrRestartHelperExitRc
}
STATUS current
DESCRIPTION
"These virtual neighbor objects are used for
managing/monitoring OSPFv3 virtual neighbors."
::= { hwOspfv3Groups 10 }
hwOspfv3AreaAggregateGroup OBJECT-GROUP
OBJECTS {
hwOspfv3AreaAggregateRowStatus,
hwOspfv3AreaAggregateEffect
}
STATUS current
DESCRIPTION
"These area aggregate objects used required for
aggregating OSPFv3 prefixes for summarization
across areas."
::= { hwOspfv3Groups 11 }
hwOspfv3NotificationObjectGroup OBJECT-GROUP
OBJECTS {
hwOspfv3ConfigErrorType,
hwOspfv3PacketType,
hwOspfv3PacketSrc,
hwOspfv3IfName,
hwOspfv3IfStateChgReason,
hwOspfv3NbrStateChgReason
}
STATUS current
DESCRIPTION
"These objects are used to record notification
parameters"
::= { hwOspfv3Groups 12 }
hwOspfv3NotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
hwOspfv3VirtIfStateChange,
hwOspfv3NbrStateChange,
hwOspfv3VirtNbrStateChange,
hwOspfv3IfConfigError,
hwOspfv3VirtIfConfigError,
hwOspfv3IfRxBadPacket,
hwOspfv3VirtIfRxBadPacket,
hwOspfv3IfStateChange,
hwOspfv3RestartStatusChange,
hwOspfv3NbrRestartHelperStatusChange,
hwOspfv3VirtNbrRestartHelperStatusChange,
hwOspfv3NssaTranslatorStatusChange
}
STATUS current
DESCRIPTION
"This group is used for OSPFv3 notifications"
::= { hwOspfv3Groups 13 }
END
View Git Blame Copy Permalink