635 lines
25 KiB
Plaintext
635 lines
25 KiB
Plaintext
-- =================================================================
|
|
-- Description: MPLS-TC-STD-MIB
|
|
-- Reference:
|
|
-- =================================================================
|
|
MPLS-TC-STD-MIB DEFINITIONS ::= BEGIN
|
|
|
|
IMPORTS
|
|
|
|
MODULE-IDENTITY,
|
|
Unsigned32, Integer32,
|
|
transmission FROM SNMPv2-SMI -- [RFC2578]
|
|
|
|
TEXTUAL-CONVENTION
|
|
FROM SNMPv2-TC; -- [RFC2579]
|
|
|
|
mplsTCStdMIB MODULE-IDENTITY
|
|
LAST-UPDATED "200406030000Z" -- June 3, 2004
|
|
ORGANIZATION
|
|
"IETF Multiprotocol Label Switching (MPLS) Working
|
|
Group."
|
|
CONTACT-INFO
|
|
" Thomas D. Nadeau
|
|
Cisco Systems, Inc.
|
|
tnadeau@cisco.com
|
|
|
|
Joan Cucchiara
|
|
Marconi Communications, Inc.
|
|
jcucchiara@mindspring.com
|
|
|
|
Cheenu Srinivasan
|
|
Bloomberg L.P.
|
|
cheenu@bloomberg.net
|
|
|
|
Arun Viswanathan
|
|
Force10 Networks, Inc.
|
|
arunv@force10networks.com
|
|
|
|
Hans Sjostrand
|
|
ipUnplugged
|
|
hans@ipunplugged.com
|
|
|
|
Kireeti Kompella
|
|
Juniper Networks
|
|
kireeti@juniper.net
|
|
|
|
Email comments to the MPLS WG Mailing List at
|
|
mpls@uu.net."
|
|
DESCRIPTION
|
|
"Copyright (C) The Internet Society (2004). The
|
|
initial version of this MIB module was published
|
|
in RFC 3811. For full legal notices see the RFC
|
|
itself or see:
|
|
http://www.ietf.org/copyrights/ianamib.html
|
|
|
|
This MIB module defines TEXTUAL-CONVENTIONs
|
|
for concepts used in Multiprotocol Label
|
|
Switching (MPLS) networks."
|
|
|
|
REVISION "200406030000Z" -- June 3, 2004
|
|
DESCRIPTION
|
|
"Initial version published as part of RFC 3811."
|
|
|
|
::= { mplsStdMIB 1 }
|
|
|
|
mplsStdMIB OBJECT IDENTIFIER
|
|
|
|
::= { transmission 166 }
|
|
|
|
MplsAtmVcIdentifier ::= TEXTUAL-CONVENTION
|
|
DISPLAY-HINT "d"
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A Label Switching Router (LSR) that
|
|
creates LDP sessions on ATM interfaces
|
|
uses the VCI or VPI/VCI field to hold the
|
|
LDP Label.
|
|
|
|
VCI values MUST NOT be in the 0-31 range.
|
|
The values 0 to 31 are reserved for other uses
|
|
by the ITU and ATM Forum. The value
|
|
of 32 can only be used for the Control VC,
|
|
although values greater than 32 could be
|
|
configured for the Control VC.
|
|
|
|
If a value from 0 to 31 is used for a VCI
|
|
the management entity controlling the LDP
|
|
subsystem should reject this with an
|
|
inconsistentValue error. Also, if
|
|
the value of 32 is used for a VC which is
|
|
NOT the Control VC, this should
|
|
result in an inconsistentValue error."
|
|
REFERENCE
|
|
"MPLS using LDP and ATM VC Switching, RFC3035."
|
|
SYNTAX Integer32 (32..65535)
|
|
|
|
MplsBitRate ::= TEXTUAL-CONVENTION
|
|
DISPLAY-HINT "d"
|
|
STATUS current
|
|
DESCRIPTION
|
|
"If the value of this object is greater than zero,
|
|
then this represents the bandwidth of this MPLS
|
|
interface (or Label Switched Path) in units of
|
|
'1,000 bits per second'.
|
|
|
|
The value, when greater than zero, represents the
|
|
bandwidth of this MPLS interface (rounded to the
|
|
nearest 1,000) in units of 1,000 bits per second.
|
|
If the bandwidth of the MPLS interface is between
|
|
((n * 1000) - 500) and ((n * 1000) + 499), the value
|
|
of this object is n, such that n > 0.
|
|
|
|
If the value of this object is 0 (zero), this
|
|
means that the traffic over this MPLS interface is
|
|
considered to be best effort."
|
|
SYNTAX Unsigned32 (0|1..4294967295)
|
|
|
|
MplsBurstSize ::= TEXTUAL-CONVENTION
|
|
DISPLAY-HINT "d"
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The number of octets of MPLS data that the stream
|
|
may send back-to-back without concern for policing.
|
|
The value of zero indicates that an implementation
|
|
does not support Burst Size."
|
|
SYNTAX Unsigned32 (0..4294967295)
|
|
|
|
MplsExtendedTunnelId ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A unique identifier for an MPLS Tunnel. This may
|
|
represent an IPv4 address of the ingress or egress
|
|
LSR for the tunnel. This value is derived from the
|
|
Extended Tunnel Id in RSVP or the Ingress Router ID
|
|
for CR-LDP."
|
|
REFERENCE
|
|
"RSVP-TE: Extensions to RSVP for LSP Tunnels,
|
|
[RFC3209].
|
|
|
|
Constraint-Based LSP Setup using LDP, [RFC3212]."
|
|
SYNTAX Unsigned32(0..4294967295)
|
|
|
|
MplsLabel ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This value represents an MPLS label as defined in
|
|
[RFC3031], [RFC3032], [RFC3034], [RFC3035] and
|
|
[RFC3471].
|
|
|
|
The label contents are specific to the label being
|
|
represented, such as:
|
|
|
|
* The label carried in an MPLS shim header
|
|
(for LDP this is the Generic Label) is a 20-bit
|
|
number represented by 4 octets. Bits 0-19 contain
|
|
a label or a reserved label value. Bits 20-31
|
|
MUST be zero.
|
|
|
|
The following is quoted directly from [RFC3032].
|
|
There are several reserved label values:
|
|
|
|
i. A value of 0 represents the
|
|
'IPv4 Explicit NULL Label'. This label
|
|
value is only legal at the bottom of the
|
|
label stack. It indicates that the label
|
|
stack must be popped, and the forwarding
|
|
of the packet must then be based on the
|
|
IPv4 header.
|
|
|
|
ii. A value of 1 represents the
|
|
'Router Alert Label'. This label value is
|
|
legal anywhere in the label stack except at
|
|
the bottom. When a received packet
|
|
contains this label value at the top of
|
|
the label stack, it is delivered to a
|
|
local software module for processing.
|
|
The actual forwarding of the packet
|
|
is determined by the label beneath it
|
|
in the stack. However, if the packet is
|
|
forwarded further, the Router Alert Label
|
|
should be pushed back onto the label stack
|
|
before forwarding. The use of this label
|
|
is analogous to the use of the
|
|
'Router Alert Option' in IP packets
|
|
[RFC2113]. Since this label
|
|
cannot occur at the bottom of the stack,
|
|
it is not associated with a
|
|
particular network layer protocol.
|
|
|
|
iii. A value of 2 represents the
|
|
'IPv6 Explicit NULL Label'. This label
|
|
value is only legal at the bottom of the
|
|
label stack. It indicates that the label
|
|
stack must be popped, and the forwarding
|
|
of the packet must then be based on the
|
|
IPv6 header.
|
|
|
|
iv. A value of 3 represents the
|
|
'Implicit NULL Label'.
|
|
This is a label that an LSR may assign and
|
|
distribute, but which never actually
|
|
appears in the encapsulation. When an
|
|
LSR would otherwise replace the label
|
|
at the top of the stack with a new label,
|
|
but the new label is 'Implicit NULL',
|
|
the LSR will pop the stack instead of
|
|
doing the replacement. Although
|
|
this value may never appear in the
|
|
encapsulation, it needs to be specified in
|
|
the Label Distribution Protocol, so a value
|
|
is reserved.
|
|
|
|
v. Values 4-15 are reserved.
|
|
|
|
* The frame relay label can be either 10-bits or
|
|
23-bits depending on the DLCI field size and the
|
|
upper 22-bits or upper 9-bits must be zero,
|
|
respectively.
|
|
|
|
* For an ATM label the lower 16-bits represents the
|
|
VCI, the next 12-bits represents the VPI and the
|
|
remaining bits MUST be zero.
|
|
|
|
* The Generalized-MPLS (GMPLS) label contains a
|
|
value greater than 2^24-1 and used in GMPLS
|
|
as defined in [RFC3471]."
|
|
REFERENCE
|
|
"Multiprotocol Label Switching Architecture,
|
|
RFC3031.
|
|
|
|
MPLS Label Stack Encoding, [RFC3032].
|
|
|
|
Use of Label Switching on Frame Relay Networks,
|
|
RFC3034.
|
|
|
|
MPLS using LDP and ATM VC Switching, RFC3035.
|
|
Generalized Multiprotocol Label Switching
|
|
(GMPLS) Architecture, [RFC3471]."
|
|
SYNTAX Unsigned32 (0..4294967295)
|
|
|
|
MplsLabelDistributionMethod ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The label distribution method which is also called
|
|
the label advertisement mode [RFC3036].
|
|
Each interface on an LSR is configured to operate
|
|
in either Downstream Unsolicited or Downstream
|
|
on Demand."
|
|
REFERENCE
|
|
"Multiprotocol Label Switching Architecture,
|
|
RFC3031.
|
|
|
|
LDP Specification, RFC3036, Section 2.6.3."
|
|
SYNTAX INTEGER {
|
|
downstreamOnDemand(1),
|
|
downstreamUnsolicited(2)
|
|
}
|
|
|
|
MplsLdpIdentifier ::= TEXTUAL-CONVENTION
|
|
DISPLAY-HINT "1d.1d.1d.1d:2d"
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The LDP identifier is a six octet
|
|
quantity which is used to identify a
|
|
Label Switching Router (LSR) label space.
|
|
The first four octets identify the LSR and
|
|
must be a globally unique value, such as a
|
|
32-bit router ID assigned to the LSR, and the
|
|
last two octets identify a specific label
|
|
space within the LSR."
|
|
SYNTAX OCTET STRING (SIZE (6))
|
|
|
|
MplsLsrIdentifier ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The Label Switching Router (LSR) identifier is the
|
|
first 4 bytes of the Label Distribution Protocol
|
|
(LDP) identifier."
|
|
SYNTAX OCTET STRING (SIZE (4))
|
|
MplsLdpLabelType ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The Layer 2 label types which are defined for MPLS
|
|
LDP and/or CR-LDP are generic(1), atm(2), or
|
|
frameRelay(3)."
|
|
SYNTAX INTEGER {
|
|
generic(1),
|
|
atm(2),
|
|
frameRelay(3)
|
|
}
|
|
|
|
MplsLSPID ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A unique identifier within an MPLS network that is
|
|
assigned to each LSP. This is assigned at the head
|
|
end of the LSP and can be used by all LSRs
|
|
to identify this LSP. This value is piggybacked by
|
|
the signaling protocol when this LSP is signaled
|
|
within the network. This identifier can then be
|
|
used at each LSR to identify which labels are
|
|
being swapped to other labels for this LSP. This
|
|
object can also be used to disambiguate LSPs that
|
|
share the same RSVP sessions between the same
|
|
source and destination.
|
|
|
|
For LSPs established using CR-LDP, the LSPID is
|
|
composed of the ingress LSR Router ID (or any of
|
|
its own IPv4 addresses) and a locally unique
|
|
CR-LSP ID to that LSR. The first two bytes carry
|
|
the CR-LSPID, and the remaining 4 bytes carry
|
|
the Router ID. The LSPID is useful in network
|
|
management, in CR-LSP repair, and in using
|
|
an already established CR-LSP as a hop in
|
|
an ER-TLV.
|
|
|
|
For LSPs signaled using RSVP-TE, the LSP ID is
|
|
defined as a 16-bit (2 byte) identifier used
|
|
in the SENDER_TEMPLATE and the FILTER_SPEC
|
|
that can be changed to allow a sender to
|
|
share resources with itself. The length of this
|
|
object should only be 2 or 6 bytes. If the length
|
|
of this octet string is 2 bytes, then it must
|
|
identify an RSVP-TE LSPID, or it is 6 bytes,
|
|
it must contain a CR-LDP LSPID."
|
|
REFERENCE
|
|
"RSVP-TE: Extensions to RSVP for LSP Tunnels,
|
|
[RFC3209].
|
|
|
|
Constraint-Based LSP Setup using LDP,
|
|
[RFC3212]."
|
|
SYNTAX OCTET STRING (SIZE (2|6))
|
|
|
|
MplsLspType ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Types of Label Switch Paths (LSPs)
|
|
on a Label Switching Router (LSR) or a
|
|
Label Edge Router (LER) are:
|
|
|
|
unknown(1) -- if the LSP is not known
|
|
to be one of the following.
|
|
|
|
terminatingLsp(2) -- if the LSP terminates
|
|
on the LSR/LER, then this
|
|
is an egressing LSP
|
|
which ends on the LSR/LER,
|
|
|
|
originatingLsp(3) -- if the LSP originates
|
|
from this LSR/LER, then
|
|
this is an ingressing LSP
|
|
which is the head-end of
|
|
the LSP,
|
|
|
|
crossConnectingLsp(4) -- if the LSP ingresses
|
|
and egresses on the LSR,
|
|
then it is
|
|
cross-connecting on that
|
|
LSR."
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
terminatingLsp(2),
|
|
originatingLsp(3),
|
|
crossConnectingLsp(4)
|
|
}
|
|
|
|
MplsOwner ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object indicates the local network
|
|
management subsystem that originally created
|
|
the object(s) in question. The values of
|
|
this enumeration are defined as follows:
|
|
|
|
unknown(1) - the local network management
|
|
subsystem cannot discern which
|
|
component created the object.
|
|
|
|
other(2) - the local network management
|
|
subsystem is able to discern which component
|
|
created the object, but the component is not
|
|
listed within the following choices,
|
|
e.g., command line interface (cli).
|
|
|
|
snmp(3) - The Simple Network Management Protocol
|
|
was used to configure this object initially.
|
|
|
|
ldp(4) - The Label Distribution Protocol was
|
|
used to configure this object initially.
|
|
|
|
crldp(5) - The Constraint-Based Label Distribution
|
|
Protocol was used to configure this object
|
|
initially.
|
|
|
|
rsvpTe(6) - The Resource Reservation Protocol was
|
|
used to configure this object initially.
|
|
|
|
policyAgent(7) - A policy agent (perhaps in
|
|
combination with one of the above protocols) was
|
|
used to configure this object initially.
|
|
|
|
An object created by any of the above choices
|
|
MAY be modified or destroyed by the same or a
|
|
different choice."
|
|
SYNTAX INTEGER {
|
|
unknown(1),
|
|
other(2),
|
|
snmp(3),
|
|
ldp(4),
|
|
crldp(5),
|
|
rsvpTe(6),
|
|
policyAgent(7)
|
|
}
|
|
|
|
MplsPathIndexOrZero ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A unique identifier used to identify a specific
|
|
path used by a tunnel. A value of 0 (zero) means
|
|
that no path is in use."
|
|
SYNTAX Unsigned32(0..4294967295)
|
|
|
|
MplsPathIndex ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A unique value to index (by Path number) an
|
|
entry in a table."
|
|
SYNTAX Unsigned32(1..4294967295)
|
|
|
|
MplsRetentionMode ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The label retention mode which specifies whether
|
|
an LSR maintains a label binding for a FEC
|
|
learned from a neighbor that is not its next hop
|
|
for the FEC.
|
|
|
|
If the value is conservative(1) then advertised
|
|
label mappings are retained only if they will be
|
|
used to forward packets, i.e., if label came from
|
|
a valid next hop.
|
|
|
|
If the value is liberal(2) then all advertised
|
|
label mappings are retained whether they are from
|
|
a valid next hop or not."
|
|
REFERENCE
|
|
"Multiprotocol Label Switching Architecture,
|
|
RFC3031.
|
|
|
|
LDP Specification, RFC3036, Section 2.6.2."
|
|
SYNTAX INTEGER {
|
|
conservative(1),
|
|
liberal(2)
|
|
}
|
|
MplsTunnelAffinity ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Describes the configured 32-bit Include-any,
|
|
include-all, or exclude-all constraint for
|
|
constraint-based link selection."
|
|
REFERENCE
|
|
"RSVP-TE: Extensions to RSVP for LSP Tunnels,
|
|
RFC3209, Section 4.7.4."
|
|
SYNTAX Unsigned32(0..4294967295)
|
|
|
|
MplsTunnelIndex ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A unique index into mplsTunnelTable.
|
|
For tunnels signaled using RSVP, this value
|
|
should correspond to the RSVP Tunnel ID
|
|
used for the RSVP-TE session."
|
|
SYNTAX Unsigned32 (0..65535)
|
|
|
|
MplsTunnelInstanceIndex ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The tunnel entry with instance index 0
|
|
should refer to the configured tunnel
|
|
interface (if one exists).
|
|
|
|
Values greater than 0, but less than or
|
|
equal to 65535, should be used to indicate
|
|
signaled (or backup) tunnel LSP instances.
|
|
For tunnel LSPs signaled using RSVP,
|
|
this value should correspond to the
|
|
RSVP LSP ID used for the RSVP-TE
|
|
LSP.
|
|
|
|
Values greater than 65535 apply to FRR
|
|
detour instances."
|
|
SYNTAX Unsigned32(0|1..65535|65536..4294967295)
|
|
|
|
TeHopAddressType ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A value that represents a type of address for a
|
|
Traffic Engineered (TE) Tunnel hop.
|
|
|
|
unknown(0) An unknown address type. This value
|
|
MUST be used if the value of the
|
|
corresponding TeHopAddress object is a
|
|
zero-length string. It may also be
|
|
used to indicate a TeHopAddress which
|
|
is not in one of the formats defined
|
|
below.
|
|
|
|
ipv4(1) An IPv4 network address as defined by
|
|
the InetAddressIPv4 TEXTUAL-CONVENTION
|
|
[RFC3291].
|
|
|
|
ipv6(2) A global IPv6 address as defined by
|
|
the InetAddressIPv6 TEXTUAL-CONVENTION
|
|
[RFC3291].
|
|
|
|
asnumber(3) An Autonomous System (AS) number as
|
|
defined by the TeHopAddressAS
|
|
TEXTUAL-CONVENTION.
|
|
|
|
unnum(4) An unnumbered interface index as
|
|
defined by the TeHopAddressUnnum
|
|
TEXTUAL-CONVENTION.
|
|
|
|
lspid(5) An LSP ID for TE Tunnels
|
|
(RFC3212) as defined by the
|
|
MplsLSPID TEXTUAL-CONVENTION.
|
|
|
|
Each definition of a concrete TeHopAddressType
|
|
value must be accompanied by a definition
|
|
of a TEXTUAL-CONVENTION for use with that
|
|
TeHopAddress.
|
|
|
|
To support future extensions, the TeHopAddressType
|
|
TEXTUAL-CONVENTION SHOULD NOT be sub-typed in
|
|
object type definitions. It MAY be sub-typed in
|
|
compliance statements in order to require only a
|
|
subset of these address types for a compliant
|
|
implementation.
|
|
|
|
Implementations must ensure that TeHopAddressType
|
|
objects and any dependent objects
|
|
(e.g., TeHopAddress objects) are consistent.
|
|
An inconsistentValue error must be generated
|
|
if an attempt to change a TeHopAddressType
|
|
object would, for example, lead to an
|
|
undefined TeHopAddress value that is
|
|
not defined herein. In particular,
|
|
TeHopAddressType/TeHopAddress pairs
|
|
must be changed together if the address
|
|
type changes (e.g., from ipv6(2) to ipv4(1))."
|
|
REFERENCE
|
|
"TEXTUAL-CONVENTIONs for Internet Network
|
|
Addresses, RFC3291.
|
|
|
|
Constraint-Based LSP Setup using LDP,
|
|
[RFC3212]"
|
|
|
|
SYNTAX INTEGER {
|
|
unknown(0),
|
|
ipv4(1),
|
|
ipv6(2),
|
|
asnumber(3),
|
|
unnum(4),
|
|
lspid(5)
|
|
}
|
|
|
|
TeHopAddress ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Denotes a generic Tunnel hop address,
|
|
that is, the address of a node which
|
|
an LSP traverses, including the source
|
|
and destination nodes. An address may be
|
|
very concrete, for example, an IPv4 host
|
|
address (i.e., with prefix length 32);
|
|
if this IPv4 address is an interface
|
|
address, then that particular interface
|
|
must be traversed. An address may also
|
|
specify an 'abstract node', for example,
|
|
an IPv4 address with prefix length
|
|
less than 32, in which case, the LSP
|
|
can traverse any node whose address
|
|
falls in that range. An address may
|
|
also specify an Autonomous System (AS),
|
|
in which case the LSP can traverse any
|
|
node that falls within that AS.
|
|
|
|
A TeHopAddress value is always interpreted within
|
|
the context of an TeHopAddressType value. Every
|
|
usage of the TeHopAddress TEXTUAL-CONVENTION
|
|
is required to specify the TeHopAddressType object
|
|
which provides the context. It is suggested that
|
|
the TeHopAddressType object is logically registered
|
|
before the object(s) which use the TeHopAddress
|
|
TEXTUAL-CONVENTION if they appear in the
|
|
same logical row.
|
|
|
|
The value of a TeHopAddress object must always be
|
|
consistent with the value of the associated
|
|
TeHopAddressType object. Attempts to set a
|
|
TeHopAddress object to a value which is
|
|
inconsistent with the associated TeHopAddressType
|
|
must fail with an inconsistentValue error."
|
|
SYNTAX OCTET STRING (SIZE (0..32))
|
|
|
|
TeHopAddressAS ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Represents a two or four octet AS number.
|
|
The AS number is represented in network byte
|
|
order (MSB first). A two-octet AS number has
|
|
the two MSB octets set to zero."
|
|
REFERENCE
|
|
"Textual Conventions for Internet Network
|
|
Addresses, [RFC3291]. The
|
|
InetAutonomousSystemsNumber TEXTUAL-CONVENTION
|
|
has a SYNTAX of Unsigned32, whereas this TC
|
|
has a SYNTAX of OCTET STRING (SIZE (4)).
|
|
Both TCs represent an autonomous system number
|
|
but use different syntaxes to do so."
|
|
SYNTAX OCTET STRING (SIZE (4))
|
|
|
|
TeHopAddressUnnum ::= TEXTUAL-CONVENTION
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Represents an unnumbered interface:
|
|
|
|
octets contents encoding
|
|
1-4 unnumbered interface network-byte order
|
|
|
|
The corresponding TeHopAddressType value is
|
|
unnum(5)."
|
|
SYNTAX OCTET STRING(SIZE(4))
|
|
|
|
END
|