compass-core/mibs/DISMAN-TRACEROUTE-MIB.mib

1897 lines
77 KiB
Plaintext

-- ===========================================================================
-- Copyright (C) . All rights reserved.
--
-- Description: REMOPS MIB
-- Reference: Module(DISMAN-TRACEROUTE-MIB) Extracted from RFC4560.TXT,from 97435 to 179827.Obsoletes: 2925
-- Version: V1.00
-- History:
--
-- ===========================================================================
DISMAN-TRACEROUTE-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Integer32,
Gauge32, Unsigned32, mib-2,
NOTIFICATION-TYPE,
OBJECT-IDENTITY
FROM SNMPv2-SMI -- RFC2578
RowStatus, StorageType,
TruthValue, DateAndTime
FROM SNMPv2-TC -- RFC2579
MODULE-COMPLIANCE, OBJECT-GROUP,
NOTIFICATION-GROUP
FROM SNMPv2-CONF -- RFC2580
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB -- RFC3411
InterfaceIndexOrZero -- RFC2863
FROM IF-MIB
InetAddressType, InetAddress
FROM INET-ADDRESS-MIB -- RFC4001
OperationResponseStatus
FROM DISMAN-PING-MIB; -- RFC4560
traceRouteMIB MODULE-IDENTITY
LAST-UPDATED "200606130000Z" -- 13 June 2006
ORGANIZATION "IETF Distributed Management Working Group"
CONTACT-INFO
"Juergen Quittek
NEC Europe Ltd.
Network Laboratories
Kurfuersten-Anlage 36
69115 Heidelberg
Germany
Phone: +49 6221 4342-115
Email: quittek@netlab.nec.de"
DESCRIPTION
"The Traceroute MIB (DISMAN-TRACEROUTE-MIB) provides
access to the traceroute capability at a remote host.
Copyright (C) The Internet Society (2006). This version of
this MIB module is part of RFC 4560; see the RFC itself for
full legal notices."
-- Revision history
REVISION "200606130000Z" -- 13 June 2006
DESCRIPTION
"Updated version, published as RFC 4560.
- Correctly considered IPv6 in DESCRIPTION clause of
object traceRouteCtlDataSize
- Replaced references to RFC 2575 by RFC 3415
- Replaced references to RFC 2571 by RFC 3411
- Replaced references to RFC 2851 by RFC 4001
- Clarified DESCRIPTION clause of object
traceRouteResultsLastGoodPath
- Changed range of object traceRouteCtlInitialTtl
from (0..255) to (1..255)
- Extended DESCRIPTION clause of traceRouteResultsTable
describing re-initialization of entries
- Changed SYNTAX of traceRouteResultsTestAttempts and
traceRouteResultsTestSuccesses from Unsigned32 to
Gauge32
- Changed status of traceRouteCompliance to deprecated
- Added traceRouteFullCompliance and
traceRouteMinimumCompliance
- Changed status of traceRouteGroup and
traceRouteTimeStampGroup to deprecated
- Added traceRouteMinimumGroup,
traceRouteCtlRowStatusGroup, and
traceRouteHistoryGroup
- Changed DEFVAL of object
traceRouteCtlTargetAddressType from { ipv4 }
to { unknown }
- Changed DEFVAL of object traceRouteCtlDescr
from { '00'H } to { ''H }
- Added DEFVAL for object traceRouteCtlTrapGeneration
of DEFVAL { { } }"
REVISION "200009210000Z" -- 21 September 2000
DESCRIPTION
"Initial version, published as RFC 2925."
::= { mib-2 81 }
-- Top level structure of the MIB
traceRouteNotifications OBJECT IDENTIFIER ::= { traceRouteMIB 0 }
traceRouteObjects OBJECT IDENTIFIER ::= { traceRouteMIB 1 }
traceRouteConformance OBJECT IDENTIFIER ::= { traceRouteMIB 2 }
-- The registration node (point) for traceroute implementation types
traceRouteImplementationTypeDomains OBJECT IDENTIFIER
::= { traceRouteMIB 3 }
traceRouteUsingUdpProbes OBJECT-IDENTITY
STATUS current
DESCRIPTION
"Indicates that an implementation is using UDP probes to
perform the traceroute operation."
::= { traceRouteImplementationTypeDomains 1 }
-- Simple Object Definitions
traceRouteMaxConcurrentRequests OBJECT-TYPE
SYNTAX Unsigned32
UNITS "requests"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum number of concurrent active traceroute requests
that are allowed within an agent implementation. A value
of 0 for this object implies that there is no limit for
the number of concurrent active requests in effect.
The limit applies only to new requests being activated.
When a new value is set, the agent will continue processing
all the requests already active, even if their number
exceeds the limit just imposed."
DEFVAL { 10 }
::= { traceRouteObjects 1 }
-- Traceroute Control Table
traceRouteCtlTable OBJECT-TYPE
SYNTAX SEQUENCE OF TraceRouteCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines the Remote Operations Traceroute Control Table for
providing the capability of invoking traceroute from a remote
host. The results of traceroute operations can be stored in
the traceRouteResultsTable, traceRouteProbeHistoryTable, and
the traceRouteHopsTable."
::= { traceRouteObjects 2 }
traceRouteCtlEntry OBJECT-TYPE
SYNTAX TraceRouteCtlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines an entry in the traceRouteCtlTable. The first
index element, traceRouteCtlOwnerIndex, is of type
SnmpAdminString, a textual convention that allows for
use of the SNMPv3 View-Based Access Control Model
(RFC 3415, VACM) and that allows a management
application to identify its entries. The second index,
traceRouteCtlTestName (also an SnmpAdminString),
enables the same management application to have
multiple requests outstanding."
INDEX {
traceRouteCtlOwnerIndex,
traceRouteCtlTestName
}
::= { traceRouteCtlTable 1 }
TraceRouteCtlEntry ::=
SEQUENCE {
traceRouteCtlOwnerIndex SnmpAdminString,
traceRouteCtlTestName SnmpAdminString,
traceRouteCtlTargetAddressType InetAddressType,
traceRouteCtlTargetAddress InetAddress,
traceRouteCtlByPassRouteTable TruthValue,
traceRouteCtlDataSize Unsigned32,
traceRouteCtlTimeOut Unsigned32,
traceRouteCtlProbesPerHop Unsigned32,
traceRouteCtlPort Unsigned32,
traceRouteCtlMaxTtl Unsigned32,
traceRouteCtlDSField Unsigned32,
traceRouteCtlSourceAddressType InetAddressType,
traceRouteCtlSourceAddress InetAddress,
traceRouteCtlIfIndex InterfaceIndexOrZero,
traceRouteCtlMiscOptions SnmpAdminString,
traceRouteCtlMaxFailures Unsigned32,
traceRouteCtlDontFragment TruthValue,
traceRouteCtlInitialTtl Unsigned32,
traceRouteCtlFrequency Unsigned32,
traceRouteCtlStorageType StorageType,
traceRouteCtlAdminStatus INTEGER,
traceRouteCtlDescr SnmpAdminString,
traceRouteCtlMaxRows Unsigned32,
traceRouteCtlTrapGeneration BITS,
traceRouteCtlCreateHopsEntries TruthValue,
traceRouteCtlType OBJECT IDENTIFIER,
traceRouteCtlRowStatus RowStatus
}
traceRouteCtlOwnerIndex OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"To facilitate the provisioning of access control by a
security administrator using the View-Based Access
Control Model (RFC 3415, VACM) for tables in which
multiple users may need to create or
modify entries independently, the initial index is used as
an 'owner index'. Such an initial index has a syntax of
SnmpAdminString and can thus be trivially mapped to a
securityName or groupName defined in VACM, in
accordance with a security policy.
When used in conjunction with such a security policy,
all entries in the table belonging to a particular user
(or group) will have the same value for this initial
index. For a given user's entries in a particular
table, the object identifiers for the information in
these entries will have the same subidentifiers (except
for the 'column' subidentifier) up to the end of the
encoded owner index. To configure VACM to permit access
to this portion of the table, one would create
vacmViewTreeFamilyTable entries with the value of
vacmViewTreeFamilySubtree including the owner index
portion, and vacmViewTreeFamilyMask 'wildcarding' the
column subidentifier. More elaborate configurations
are possible."
::= { traceRouteCtlEntry 1 }
traceRouteCtlTestName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The name of a traceroute test. This is locally unique,
within the scope of a traceRouteCtlOwnerIndex."
::= { traceRouteCtlEntry 2 }
traceRouteCtlTargetAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the type of host address to be used on the
traceroute request at the remote host."
DEFVAL { unknown }
::= { traceRouteCtlEntry 3 }
traceRouteCtlTargetAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the host address used on the
traceroute request at the remote host. The
host address type can be determined by
examining the value of the corresponding
traceRouteCtlTargetAddressType.
A value for this object MUST be set prior to
transitioning its corresponding traceRouteCtlEntry to
active(1) via traceRouteCtlRowStatus."
::= { traceRouteCtlEntry 4 }
traceRouteCtlByPassRouteTable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The purpose of this object is to enable optional
bypassing the route table. If enabled, the remote
host will bypass the normal routing tables and send
directly to a host on an attached network. If the
host is not on a directly attached network, an
error is returned. This option can be used to perform
the traceroute operation to a local host through an
interface that has no route defined (e.g., after the
interface was dropped by the routing daemon at the host)."
DEFVAL { false }
::= { traceRouteCtlEntry 5 }
traceRouteCtlDataSize OBJECT-TYPE
SYNTAX Unsigned32 (0..65507)
UNITS "octets"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the size of the data portion of a traceroute
request, in octets. If the RECOMMENDED traceroute method
(UDP datagrams as probes) is used, then the value
contained in this object MUST be applied. If another
traceroute method is used for which the specified size
is not appropriate, then the implementation SHOULD use
whatever size (appropriate to the method) is closest to
the specified size.
The maximum value for this object was computed by
subtracting the smallest possible IP header size of
20 octets (IPv4 header with no options) and the UDP
header size of 8 octets from the maximum IP packet size.
An IP packet has a maximum size of 65535 octets
(excluding IPv6 Jumbograms)."
DEFVAL { 0 }
::= { traceRouteCtlEntry 6 }
traceRouteCtlTimeOut OBJECT-TYPE
SYNTAX Unsigned32 (1..60)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the time-out value, in seconds, for
a traceroute request."
DEFVAL { 3 }
::= { traceRouteCtlEntry 7 }
traceRouteCtlProbesPerHop OBJECT-TYPE
SYNTAX Unsigned32 (1..10)
UNITS "probes"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the number of times to reissue a traceroute
request with the same time-to-live (TTL) value."
DEFVAL { 3 }
::= { traceRouteCtlEntry 8 }
traceRouteCtlPort OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
UNITS "UDP Port"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the (initial) UDP port to send the traceroute
request to. A port needs to be specified that is not in
use at the destination (target) host. The default
value for this object is the IANA assigned port,
33434, for the traceroute function."
DEFVAL { 33434 }
::= { traceRouteCtlEntry 9 }
traceRouteCtlMaxTtl OBJECT-TYPE
SYNTAX Unsigned32 (1..255)
UNITS "time-to-live value"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the maximum time-to-live value."
DEFVAL { 30 }
::= { traceRouteCtlEntry 10 }
traceRouteCtlDSField OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the value to store in the Type of Service
(TOS) octet in the IPv4 header or in the Traffic
Class octet in the IPv6 header, respectively, of the
IP packet used to encapsulate the traceroute probe.
The octet to be set in the IP header contains the
Differentiated Services (DS) Field in the six most
significant bits.
This option can be used to determine what effect an
explicit DS Field setting has on a traceroute response.
Not all values are legal or meaningful. A value of 0
means that the function represented by this option is
not supported. DS Field usage is often not supported
by IP implementations, and not all values are supported.
Refer to RFC 2474 and RFC 3260 for guidance on usage of
this field."
REFERENCE
"Refer to RFC 1812 for the definition of the IPv4 TOS
octet and to RFC 2460 for the definition of the IPv6
Traffic Class octet. Refer to RFC 2474 and RFC 3260
for the definition of the Differentiated Services Field."
DEFVAL { 0 }
::= { traceRouteCtlEntry 11 }
traceRouteCtlSourceAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the type of the source address,
traceRouteCtlSourceAddress, to be used at a remote host
when a traceroute operation is performed."
DEFVAL { unknown }
::= { traceRouteCtlEntry 12 }
traceRouteCtlSourceAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Use the specified IP address (which must be given as an
IP number, not a hostname) as the source address in
outgoing probe packets. On hosts with more than one IP
address, this option can be used to select the address
to be used. If the IP address is not one of this
machine's interface addresses, an error is returned, and
nothing is sent. A zero-length octet string value for
this object disables source address specification.
The address type (InetAddressType) that relates to
this object is specified by the corresponding value
of traceRouteCtlSourceAddressType."
DEFVAL { ''H }
::= { traceRouteCtlEntry 13 }
traceRouteCtlIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Setting this object to an interface's ifIndex prior
to starting a remote traceroute operation directs
the traceroute probes to be transmitted over the
specified interface. A value of zero for this object
implies that this option is not enabled."
DEFVAL { 0 }
::= { traceRouteCtlEntry 14 }
traceRouteCtlMiscOptions OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Enables an application to specify implementation-dependent
options."
DEFVAL { ''H }
::= { traceRouteCtlEntry 15 }
traceRouteCtlMaxFailures OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "timeouts"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object indicates the maximum number
of consecutive timeouts allowed before a remote traceroute
request is terminated. A value of either 255 (maximum
hop count/possible TTL value) or 0 indicates that the
function of terminating a remote traceroute request when a
specific number of consecutive timeouts are detected is
disabled."
DEFVAL { 5 }
::= { traceRouteCtlEntry 16 }
traceRouteCtlDontFragment OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object enables setting of the don't fragment flag (DF)
in the IP header for a probe. Use of this object enables
a manual PATH MTU test is performed."
DEFVAL { false }
::= { traceRouteCtlEntry 17 }
traceRouteCtlInitialTtl OBJECT-TYPE
SYNTAX Unsigned32 (1..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object specifies the initial TTL value to
use. This enables bypassing the initial (often well known)
portion of a path."
DEFVAL { 1 }
::= { traceRouteCtlEntry 18 }
traceRouteCtlFrequency OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds to wait before repeating a
traceroute test, as defined by the value of the
various objects in the corresponding row.
After a single test is completed the number of seconds
as defined by the value of traceRouteCtlFrequency MUST
elapse before the next traceroute test is started.
A value of 0 for this object implies that the test
as defined by the corresponding entry will not be
repeated."
DEFVAL { 0 }
::= { traceRouteCtlEntry 19 }
traceRouteCtlStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this conceptual row.
Conceptual rows having the value 'permanent' need not
allow write-access to any columnar objects in the row."
DEFVAL { nonVolatile }
::= { traceRouteCtlEntry 20 }
traceRouteCtlAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
enabled(1), -- operation should be started
disabled(2) -- operation should be stopped
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Reflects the desired state that an traceRouteCtlEntry
should be in:
enabled(1) - Attempt to activate the test as defined by
this traceRouteCtlEntry.
disabled(2) - Deactivate the test as defined by this
traceRouteCtlEntry.
Refer to the corresponding traceRouteResultsOperStatus to
determine the operational state of the test defined by
this entry."
DEFVAL { disabled }
::= { traceRouteCtlEntry 21 }
traceRouteCtlDescr OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The purpose of this object is to provide a
descriptive name of the remote traceroute
test."
DEFVAL { ''H }
::= { traceRouteCtlEntry 22 }
traceRouteCtlMaxRows OBJECT-TYPE
SYNTAX Unsigned32
UNITS "rows"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum number of corresponding entries allowed
in the traceRouteProbeHistoryTable. An implementation
of this MIB will remove the oldest corresponding entry
in the traceRouteProbeHistoryTable to allow the
addition of an new entry once the number of
corresponding rows in the traceRouteProbeHistoryTable
reaches this value.
Old entries are not removed when a new test is
started. Entries are added to the
traceRouteProbeHistoryTable until traceRouteCtlMaxRows
is reached before entries begin to be removed.
A value of 0 for this object disables creation of
traceRouteProbeHistoryTable entries."
DEFVAL { 50 }
::= { traceRouteCtlEntry 23 }
traceRouteCtlTrapGeneration OBJECT-TYPE
SYNTAX BITS {
pathChange(0),
testFailure(1),
testCompletion(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object determines when and whether to
generate a notification for this entry:
pathChange(0) - Generate a traceRoutePathChange
notification when the current path varies from a
previously determined path.
testFailure(1) - Generate a traceRouteTestFailed
notification when the full path to a target
can't be determined.
testCompletion(2) - Generate a traceRouteTestCompleted
notification when the path to a target has been
determined.
The value of this object defaults to an empty set,
indicating that none of the above options has been
selected."
DEFVAL { { } }
::= { traceRouteCtlEntry 24 }
traceRouteCtlCreateHopsEntries OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The current path for a traceroute test is kept in the
traceRouteHopsTable on a per-hop basis when the value of
this object is true(1)."
DEFVAL { false }
::= { traceRouteCtlEntry 25 }
traceRouteCtlType OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object is used either to report or to
select the implementation method to be used for
performing a traceroute operation. The value of this
object may be selected from
traceRouteImplementationTypeDomains.
Additional implementation types should be allocated as
required by implementers of the DISMAN-TRACEROUTE-MIB
under their enterprise specific registration point,
not beneath traceRouteImplementationTypeDomains."
DEFVAL { traceRouteUsingUdpProbes }
::= { traceRouteCtlEntry 26 }
traceRouteCtlRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object allows entries to be created and deleted
in the traceRouteCtlTable. Deletion of an entry in
this table results in a deletion of all corresponding (same
traceRouteCtlOwnerIndex and traceRouteCtlTestName
index values) traceRouteResultsTable,
traceRouteProbeHistoryTable, and traceRouteHopsTable
entries.
A value MUST be specified for traceRouteCtlTargetAddress
prior to acceptance of a transition to active(1) state.
When a value for pingCtlTargetAddress is set,
the value of object pingCtlRowStatus changes
from notReady(3) to notInService(2).
Activation of a remote traceroute operation is
controlled via traceRouteCtlAdminStatus, and not
by transitioning of this object's value to active(1).
Transitions in and out of active(1) state are not
allowed while an entry's traceRouteResultsOperStatus
is active(1), with the exception that deletion of
an entry in this table by setting its RowStatus
object to destroy(6) will stop an active
traceroute operation.
The operational state of an traceroute operation
can be determined by examination of the corresponding
traceRouteResultsOperStatus object."
REFERENCE
"See definition of RowStatus in RFC 2579, 'Textual
Conventions for SMIv2.'"
::= { traceRouteCtlEntry 27 }
-- Traceroute Results Table
traceRouteResultsTable OBJECT-TYPE
SYNTAX SEQUENCE OF TraceRouteResultsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines the Remote Operations Traceroute Results Table for
keeping track of the status of a traceRouteCtlEntry.
An entry is added to the traceRouteResultsTable when an
traceRouteCtlEntry is started by successful transition
of its traceRouteCtlAdminStatus object to enabled(1).
If the object traceRouteCtlAdminStatus already has the value
enabled(1), and if the corresponding
traceRouteResultsOperStatus object has the value
completed(3), then successfully writing enabled(1) to the
object traceRouteCtlAdminStatus re-initializes the already
existing entry in the traceRouteResultsTable. The values of
objects in the re-initialized entry are the same as
the values of objects in a new entry would be.
An entry is removed from the traceRouteResultsTable when
its corresponding traceRouteCtlEntry is deleted."
::= { traceRouteObjects 3 }
traceRouteResultsEntry OBJECT-TYPE
SYNTAX TraceRouteResultsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines an entry in the traceRouteResultsTable. The
traceRouteResultsTable has the same indexing as the
traceRouteCtlTable so that a traceRouteResultsEntry
corresponds to the traceRouteCtlEntry that caused it to
be created."
INDEX {
traceRouteCtlOwnerIndex,
traceRouteCtlTestName
}
::= { traceRouteResultsTable 1 }
TraceRouteResultsEntry ::=
SEQUENCE {
traceRouteResultsOperStatus INTEGER,
traceRouteResultsCurHopCount Gauge32,
traceRouteResultsCurProbeCount Gauge32,
traceRouteResultsIpTgtAddrType InetAddressType,
traceRouteResultsIpTgtAddr InetAddress,
traceRouteResultsTestAttempts Gauge32,
traceRouteResultsTestSuccesses Gauge32,
traceRouteResultsLastGoodPath DateAndTime
}
traceRouteResultsOperStatus OBJECT-TYPE
SYNTAX INTEGER {
enabled(1), -- test is in progress
disabled(2), -- test has stopped
completed(3) -- test is completed
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Reflects the operational state of an traceRouteCtlEntry:
enabled(1) - Test is active.
disabled(2) - Test has stopped.
completed(3) - Test is completed."
::= { traceRouteResultsEntry 1 }
traceRouteResultsCurHopCount OBJECT-TYPE
SYNTAX Gauge32
UNITS "hops"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Reflects the current TTL value (from 1 to
255) for a remote traceroute operation.
Maximum TTL value is determined by
traceRouteCtlMaxTtl."
::= { traceRouteResultsEntry 2 }
traceRouteResultsCurProbeCount OBJECT-TYPE
SYNTAX Gauge32
UNITS "probes"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Reflects the current probe count (1..10) for
a remote traceroute operation. The maximum
probe count is determined by
traceRouteCtlProbesPerHop."
::= { traceRouteResultsEntry 3 }
traceRouteResultsIpTgtAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the type of address stored
in the corresponding traceRouteResultsIpTgtAddr
object."
::= { traceRouteResultsEntry 4 }
traceRouteResultsIpTgtAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reports the IP address associated
with a traceRouteCtlTargetAddress value when the
destination address is specified as a DNS name.
The value of this object should be a zero-length
octet string when a DNS name is not specified or
when a specified DNS name fails to resolve."
::= { traceRouteResultsEntry 5 }
traceRouteResultsTestAttempts OBJECT-TYPE
SYNTAX Gauge32
UNITS "tests"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current number of attempts to determine a path
to a target. The value of this object MUST be started
at 0."
::= { traceRouteResultsEntry 6 }
traceRouteResultsTestSuccesses OBJECT-TYPE
SYNTAX Gauge32
UNITS "tests"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current number of attempts to determine a path
to a target that have succeeded. The value of this
object MUST be reported as 0 when no attempts have
succeeded."
::= { traceRouteResultsEntry 7 }
traceRouteResultsLastGoodPath OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The date and time when the last complete path
was determined. A path is complete if responses
were received or timeout occurred for each hop on
the path; i.e., for each TTL value from the value
of the corresponding traceRouteCtlInitialTtl object
up to the end of the path or (if no reply from the
target IP address was received) up to the value of
the corresponding traceRouteCtlMaxTtl object."
::= { traceRouteResultsEntry 8 }
-- Trace Route Probe History Table
traceRouteProbeHistoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF TraceRouteProbeHistoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines the Remote Operations Traceroute Results Table
for storing the results of a traceroute operation.
An implementation of this MIB will remove the oldest
entry in the traceRouteProbeHistoryTable of the
corresponding entry in the traceRouteCtlTable to allow
the addition of a new entry once the number of rows in
the traceRouteProbeHistoryTable reaches the value specified
by traceRouteCtlMaxRows for the corresponding entry in the
traceRouteCtlTable."
::= { traceRouteObjects 4 }
traceRouteProbeHistoryEntry OBJECT-TYPE
SYNTAX TraceRouteProbeHistoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines a table for storing the results of a traceroute
operation. Entries in this table are limited by
the value of the corresponding traceRouteCtlMaxRows
object.
The first two index elements identify the
traceRouteCtlEntry that a traceRouteProbeHistoryEntry
belongs to. The third index element selects a single
traceroute operation result. The fourth and fifth indexes
select the hop and the probe for a particular
traceroute operation."
INDEX {
traceRouteCtlOwnerIndex,
traceRouteCtlTestName,
traceRouteProbeHistoryIndex,
traceRouteProbeHistoryHopIndex,
traceRouteProbeHistoryProbeIndex
}
::= { traceRouteProbeHistoryTable 1 }
TraceRouteProbeHistoryEntry ::=
SEQUENCE {
traceRouteProbeHistoryIndex Unsigned32,
traceRouteProbeHistoryHopIndex Unsigned32,
traceRouteProbeHistoryProbeIndex Unsigned32,
traceRouteProbeHistoryHAddrType InetAddressType,
traceRouteProbeHistoryHAddr InetAddress,
traceRouteProbeHistoryResponse Unsigned32,
traceRouteProbeHistoryStatus OperationResponseStatus,
traceRouteProbeHistoryLastRC Integer32,
traceRouteProbeHistoryTime DateAndTime
}
traceRouteProbeHistoryIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..'ffffffff'h)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created when the result of
a traceroute probe is determined. The initial 2 instance
identifier index values identify the traceRouteCtlEntry
that a probe result (traceRouteProbeHistoryEntry) belongs
to. An entry is removed from this table when
its corresponding traceRouteCtlEntry is deleted.
An implementation MUST start assigning
traceRouteProbeHistoryIndex values at 1 and wrap after
exceeding the maximum possible value, as defined by the
limit of this object ('ffffffff'h)."
::= { traceRouteProbeHistoryEntry 1 }
traceRouteProbeHistoryHopIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..255)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Indicates which hop in a traceroute path the probe's
results are for. The value of this object is initially
determined by the value of traceRouteCtlInitialTtl."
::= { traceRouteProbeHistoryEntry 2 }
traceRouteProbeHistoryProbeIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..10)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Indicates the index of a probe for a particular
hop in a traceroute path. The number of probes per
hop is determined by the value of the corresponding
traceRouteCtlProbesPerHop object."
::= { traceRouteProbeHistoryEntry 3 }
traceRouteProbeHistoryHAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This objects indicates the type of address stored
in the corresponding traceRouteProbeHistoryHAddr
object."
::= { traceRouteProbeHistoryEntry 4 }
traceRouteProbeHistoryHAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The address of a hop in a traceroute path. This object
is not allowed to be a DNS name. The value of the
corresponding object, traceRouteProbeHistoryHAddrType,
indicates this object's IP address type."
::= { traceRouteProbeHistoryEntry 5 }
traceRouteProbeHistoryResponse OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time measured in milliseconds from when
a probe was sent to when its response was received or
when it timed out. The value of this object is reported
as 0 when it is not possible to transmit a probe."
::= { traceRouteProbeHistoryEntry 6 }
traceRouteProbeHistoryStatus OBJECT-TYPE
SYNTAX OperationResponseStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The result of a traceroute operation made by a remote
host for a particular probe."
::= { traceRouteProbeHistoryEntry 7 }
traceRouteProbeHistoryLastRC OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last implementation-method-specific reply code received.
Traceroute is usually implemented by transmitting a series of
probe packets with increasing time-to-live values. A probe
packet is a UDP datagram encapsulated into an IP packet.
Each hop in a path to the target (destination) host rejects
the probe packets (probe's TTL too small, ICMP reply) until
either the maximum TTL is exceeded or the target host is
received."
::= { traceRouteProbeHistoryEntry 8 }
traceRouteProbeHistoryTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Timestamp for when this probe's results were determined."
::= { traceRouteProbeHistoryEntry 9 }
-- Traceroute Hop Results Table
traceRouteHopsTable OBJECT-TYPE
SYNTAX SEQUENCE OF TraceRouteHopsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines the Remote Operations Traceroute Hop Table for
keeping track of the results of traceroute tests on a
per-hop basis."
::= { traceRouteObjects 5 }
traceRouteHopsEntry OBJECT-TYPE
SYNTAX TraceRouteHopsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines an entry in the traceRouteHopsTable.
The first two index elements identify the
traceRouteCtlEntry that a traceRouteHopsEntry
belongs to. The third index element,
traceRouteHopsHopIndex, selects a
hop in a traceroute path."
INDEX {
traceRouteCtlOwnerIndex,
traceRouteCtlTestName,
traceRouteHopsHopIndex
}
::= { traceRouteHopsTable 1 }
TraceRouteHopsEntry ::=
SEQUENCE {
traceRouteHopsHopIndex Unsigned32,
traceRouteHopsIpTgtAddressType InetAddressType,
traceRouteHopsIpTgtAddress InetAddress,
traceRouteHopsMinRtt Unsigned32,
traceRouteHopsMaxRtt Unsigned32,
traceRouteHopsAverageRtt Unsigned32,
traceRouteHopsRttSumOfSquares Unsigned32,
traceRouteHopsSentProbes Unsigned32,
traceRouteHopsProbeResponses Unsigned32,
traceRouteHopsLastGoodProbe DateAndTime
}
traceRouteHopsHopIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..'ffffffff'h)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Specifies the hop index for a traceroute hop. Values
for this object with respect to the same
traceRouteCtlOwnerIndex and traceRouteCtlTestName
MUST start at 1 and be given increasing values for
subsequent hops. The value of traceRouteHopsHopIndex is not
necessarily the number of the hop on the traced path.
The traceRouteHopsTable keeps the current traceroute
path per traceRouteCtlEntry if enabled by
setting the corresponding traceRouteCtlCreateHopsEntries
to true(1).
All hops (traceRouteHopsTable entries) in a traceroute
path MUST be updated at the same time when a traceroute
operation is completed. Care needs to be applied when a path
either changes or can't be determined. The initial portion
of the path, up to the first hop change, MUST retain the
same traceRouteHopsHopIndex values. The remaining portion
of the path SHOULD be assigned new traceRouteHopsHopIndex
values."
::= { traceRouteHopsEntry 1 }
traceRouteHopsIpTgtAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the type of address stored
in the corresponding traceRouteHopsIpTgtAddress
object."
::= { traceRouteHopsEntry 2 }
traceRouteHopsIpTgtAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reports the IP address associated with
the hop. A value for this object should be reported
as a numeric IP address, not as a DNS name.
The address type (InetAddressType) that relates to
this object is specified by the corresponding value
of pingCtlSourceAddressType."
::= { traceRouteHopsEntry 3 }
traceRouteHopsMinRtt OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum traceroute round-trip-time (RTT) received for
this hop. A value of 0 for this object implies that no
RTT has been received."
::= { traceRouteHopsEntry 4 }
traceRouteHopsMaxRtt OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum traceroute round-trip-time (RTT) received for
this hop. A value of 0 for this object implies that no
RTT has been received."
::= { traceRouteHopsEntry 5 }
traceRouteHopsAverageRtt OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current average traceroute round-trip-time (RTT) for
this hop."
::= { traceRouteHopsEntry 6 }
traceRouteHopsRttSumOfSquares OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the sum of the squares of all
round-trip-times received for this hop. Its purpose is
to enable standard deviation calculation."
::= { traceRouteHopsEntry 7 }
traceRouteHopsSentProbes OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object reflects the number of probes sent
for this hop during this traceroute test. The value of this
object should start at 0."
::= { traceRouteHopsEntry 8 }
traceRouteHopsProbeResponses OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of responses received for this hop during this
traceroute test. This value of this object should start
at 0."
::= { traceRouteHopsEntry 9 }
traceRouteHopsLastGoodProbe OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Date and time at which the last response was received for a
probe for this hop during this traceroute test."
::= { traceRouteHopsEntry 10 }
-- Notification Definition section
traceRoutePathChange NOTIFICATION-TYPE
OBJECTS {
traceRouteCtlTargetAddressType,
traceRouteCtlTargetAddress,
traceRouteResultsIpTgtAddrType,
traceRouteResultsIpTgtAddr
}
STATUS current
DESCRIPTION
"The path to a target has changed."
::= { traceRouteNotifications 1 }
traceRouteTestFailed NOTIFICATION-TYPE
OBJECTS {
traceRouteCtlTargetAddressType,
traceRouteCtlTargetAddress,
traceRouteResultsIpTgtAddrType,
traceRouteResultsIpTgtAddr
}
STATUS current
DESCRIPTION
"Could not determine the path to a target."
::= { traceRouteNotifications 2 }
traceRouteTestCompleted NOTIFICATION-TYPE
OBJECTS {
traceRouteCtlTargetAddressType,
traceRouteCtlTargetAddress,
traceRouteResultsIpTgtAddrType,
traceRouteResultsIpTgtAddr
}
STATUS current
DESCRIPTION
"The path to a target has just been determined."
::= { traceRouteNotifications 3 }
-- Conformance information
-- Compliance statements
traceRouteCompliances OBJECT IDENTIFIER
::= { traceRouteConformance 1 }
traceRouteGroups OBJECT IDENTIFIER
::= { traceRouteConformance 2 }
-- Compliance statements
traceRouteFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMP entities that
fully implement the DISMAN-TRACEROUTE-MIB."
MODULE -- this module
MANDATORY-GROUPS {
traceRouteMinimumGroup,
traceRouteCtlRowStatusGroup,
traceRouteHistoryGroup
}
GROUP traceRouteHopsTableGroup
DESCRIPTION
"This group lists the objects that make up a
traceRouteHopsEntry. Support of the traceRouteHopsTable
is optional."
GROUP traceRouteNotificationsGroup
DESCRIPTION
"This group defines a collection of optional
notifications."
OBJECT traceRouteMaxConcurrentRequests
MIN-ACCESS read-only
DESCRIPTION
"The agent is not required to support SET
operations to this object."
OBJECT traceRouteCtlByPassRouteTable
MIN-ACCESS read-only
DESCRIPTION
"Write access to this object is not required by
implementations that are not capable of its
implementation. The function represented by this
object is implementable if the setsockopt
SOL_SOCKET SO_DONTROUTE option is supported."
OBJECT traceRouteCtlDSField
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. If write access is
not supported, return a 0 as the value of this object.
A value of 0 implies that the function represented by
this option is not supported."
OBJECT traceRouteCtlSourceAddressType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
MIN-ACCESS read-only
DESCRIPTION
"Write access to this object is not required by
implementations that are not capable of binding the
send socket with a source address. An implementation
is only required to support IPv4 and IPv6 addresses."
OBJECT traceRouteCtlSourceAddress
SYNTAX InetAddress (SIZE(0|4|16))
MIN-ACCESS read-only
DESCRIPTION
"Write access to this object is not required by
implementations that are not capable of binding the
send socket with a source address. An implementation
is only required to support IPv4 and IPv6 addresses."
OBJECT traceRouteCtlIfIndex
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. If write access is
not supported, return a 0 as the value of this object.
A value of 0 implies that the function represented by
this option is not supported."
OBJECT traceRouteCtlMiscOptions
MIN-ACCESS read-only
DESCRIPTION
"Support of this object is optional. If not
supporting, do not allow write access and return a
zero-length octet string as the value of the object."
OBJECT traceRouteCtlStorageType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. It is also allowed
that implementations support only the volatile(2)
StorageType enumeration."
OBJECT traceRouteCtlType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. In addition, the only
value that is RECOMMENDED to be supported by an
implementation is traceRouteUsingUdpProbes."
OBJECT traceRouteResultsIpTgtAddrType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation should only support IPv4 and
globally unique IPv6 address values for this object."
OBJECT traceRouteResultsIpTgtAddr
SYNTAX InetAddress (SIZE(0|4|16))
DESCRIPTION
"An implementation should only support IPv4 and
globally unique IPv6 address values for this object."
OBJECT traceRouteResultsLastGoodPath
DESCRIPTION
"If the traceRouteHopsTableGroup is implemented, then
this object is mandatory for implementations that have
access to a system clock and that are capable of setting
the values for DateAndTime objects. It is RECOMMENDED
that when this object is not supported its values
be reported as '0000000000000000'H."
OBJECT traceRouteProbeHistoryHAddrType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation should only support IPv4 and
globally unique IPv6 address values for this object."
OBJECT traceRouteProbeHistoryHAddr
SYNTAX InetAddress (SIZE(0|4|16))
DESCRIPTION
"An implementation should only support IPv4 and
globally unique IPv6 address values for this object."
OBJECT traceRouteProbeHistoryTime
DESCRIPTION
"This object is mandatory for implementations that have
access to a system clock and that are capable of setting
the values for DateAndTime objects. It is RECOMMENDED
that when this object is not supported its values
be reported as '0000000000000000'H."
OBJECT traceRouteHopsIpTgtAddressType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation should only support IPv4 and
globally unique IPv6 address values for this object."
OBJECT traceRouteHopsIpTgtAddress
SYNTAX InetAddress (SIZE(0|4|16))
DESCRIPTION
"An implementation should only support IPv4 and
globally unique IPv6 address values for this object."
OBJECT traceRouteHopsLastGoodProbe
DESCRIPTION
"This object is mandatory for implementations that have
access to a system clock and that are capable of setting
the values for DateAndTime objects. It is RECOMMENDED
that when this object is not supported its values
be reported as '0000000000000000'H."
::= { traceRouteCompliances 2 }
traceRouteMinimumCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The minimum compliance statement for SNMP entities
which implement the minimal subset of the
DISMAN-TRACEROUTE-MIB. Implementors might choose this
subset for small devices with limited resources."
MODULE -- this module
MANDATORY-GROUPS { traceRouteMinimumGroup }
GROUP traceRouteCtlRowStatusGroup
DESCRIPTION
"A compliant implementation does not have to implement
the traceRouteCtlRowStatusGroup."
GROUP traceRouteHistoryGroup
DESCRIPTION
"A compliant implementation does not have to implement
the traceRouteHistoryGroup."
GROUP traceRouteHopsTableGroup
DESCRIPTION
"This group lists the objects that make up a
traceRouteHopsEntry. Support of the traceRouteHopsTable
is optional."
GROUP traceRouteNotificationsGroup
DESCRIPTION
"This group defines a collection of optional
notifications."
OBJECT traceRouteMaxConcurrentRequests
MIN-ACCESS read-only
DESCRIPTION
"The agent is not required to support SET
operations to this object."
OBJECT traceRouteCtlByPassRouteTable
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. If write access is
not supported, return a false(2) as the value of this
object. A value of false(2) means that the function
represented by this option is not supported."
OBJECT traceRouteCtlDSField
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. If write access is
not supported, return a 0 as the value of this object.
A value of 0 implies that the function represented by
this option is not supported."
OBJECT traceRouteCtlSourceAddressType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
MIN-ACCESS read-only
DESCRIPTION
"Write access to this object is not required by
implementations that are not capable of binding the
send socket with a source address. An implementation
is only required to support IPv4 and IPv6 addresses."
OBJECT traceRouteCtlSourceAddress
SYNTAX InetAddress (SIZE(0|4|16))
MIN-ACCESS read-only
DESCRIPTION
"Write access to this object is not required by
implementations that are not capable of binding the
send socket with a source address. An implementation
is only required to support IPv4 and IPv6 addresses."
OBJECT traceRouteCtlIfIndex
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. If write access is
not supported, return a 0 as the value of this object.
A value of 0 implies that the function represented by
this option is not supported."
OBJECT traceRouteCtlMiscOptions
MIN-ACCESS read-only
DESCRIPTION
"Support of this object is optional. If not
supporting, do not allow write access, and return a
zero-length octet string as the value of the object."
OBJECT traceRouteCtlDontFragment
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. If write access is
not supported, return a false(2) as the value of this
object. A value of false(2) means that the function
represented by this option is not supported."
OBJECT traceRouteCtlInitialTtl
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. If write access is
not supported, return a 1 as the value of this object."
OBJECT traceRouteCtlFrequency
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. If write access is
not supported, return a 0 as the value of this object.
A value of 0 implies that the function represented by
this option is not supported."
OBJECT traceRouteCtlStorageType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. It is also allowed
that implementations support only the volatile(2)
StorageType enumeration."
OBJECT traceRouteCtlDescr
MIN-ACCESS read-only
DESCRIPTION
"The agent is not required to support set
operations to this object."
OBJECT traceRouteCtlMaxRows
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. If the
traceRouteHistoryGroup is not implemented, then write
access to this object MUST be disabled, and the object
MUST return a value of 0 when retrieved."
OBJECT traceRouteCtlTrapGeneration
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. If the
traceRouteNotificationsGroup is not implemented, then
write access to this object MUST be disabled, and the
object MUST return a value with no bit set when
retrieved. No bit set indicates that no notification
is generated."
OBJECT traceRouteCtlCreateHopsEntries
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. If the
traceRouteHopsTableGroup is not implemented, then
write access to this object MUST be disabled, and the
object MUST return a value of false(2) when retrieved."
OBJECT traceRouteCtlType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. In addition, the only
value that is RECOMMENDED to be supported by an
implementation is traceRouteUsingUdpProbes."
OBJECT traceRouteResultsIpTgtAddrType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation should only support IPv4 and
globally unique IPv6 address values for this object."
OBJECT traceRouteResultsIpTgtAddr
SYNTAX InetAddress (SIZE(0|4|16))
DESCRIPTION
"An implementation should only support IPv4 and
globally unique IPv6 address values for this object."
OBJECT traceRouteResultsLastGoodPath
DESCRIPTION
"This object is mandatory for implementations that have
access to a system clock and that are capable of setting
the values for DateAndTime objects. It is RECOMMENDED
that when this object is not supported its values
be reported as '0000000000000000'H."
OBJECT traceRouteProbeHistoryHAddrType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation should only support IPv4 and
globally unique IPv6 address values for this object."
OBJECT traceRouteProbeHistoryHAddr
SYNTAX InetAddress (SIZE(0|4|16))
DESCRIPTION
"An implementation should only support IPv4 and
globally unique IPv6 address values for this object."
OBJECT traceRouteProbeHistoryTime
DESCRIPTION
"If the traceRouteHistoryGroup is implemented, then
this object is mandatory for implementations that have
access to a system clock and that are capable of setting
the values for DateAndTime objects. It is RECOMMENDED
that when this object is not supported its values
be reported as '0000000000000000'H."
OBJECT traceRouteHopsIpTgtAddressType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation should only support IPv4 and
globally unique IPv6 address values for this object."
OBJECT traceRouteHopsIpTgtAddress
SYNTAX InetAddress (SIZE(0|4|16))
DESCRIPTION
"An implementation should only support IPv4 and
globally unique IPv6 address values for this object."
OBJECT traceRouteHopsLastGoodProbe
DESCRIPTION
"If the traceRouteHopsTableGroup is implemented, then
this object is mandatory for implementations that have
access to a system clock and that are capable of setting
the values for DateAndTime objects. It is RECOMMENDED
that when this object is not supported its values
be reported as '0000000000000000'H."
::= { traceRouteCompliances 3 }
traceRouteCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The compliance statement for the DISMAN-TRACEROUTE-MIB.
This compliance statement has been deprecated because
the traceRouteGroup and the traceRouteTimeStampGroup
have been split and deprecated. The
traceRouteFullCompliance is semantically identical to the
deprecated traceRouteCompliance statement."
MODULE -- this module
MANDATORY-GROUPS {
traceRouteGroup
}
GROUP traceRouteTimeStampGroup
DESCRIPTION
"This group is mandatory for implementations that have
access to a system clock and that are capable of setting
the values for DateAndTime objects."
GROUP traceRouteNotificationsGroup
DESCRIPTION
"This group defines a collection of optional
notifications."
GROUP traceRouteHopsTableGroup
DESCRIPTION
"This group lists the objects that make up a
traceRouteHopsEntry. Support of the traceRouteHopsTable
is optional."
OBJECT traceRouteMaxConcurrentRequests
MIN-ACCESS read-only
DESCRIPTION
"The agent is not required to support SET
operations to this object."
OBJECT traceRouteCtlByPassRouteTable
MIN-ACCESS read-only
DESCRIPTION
"This object is not required by implementations that
are not capable of its implementation. The function
represented by this object is implementable if the
setsockopt SOL_SOCKET SO_DONTROUTE option is
supported."
OBJECT traceRouteCtlSourceAddressType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
MIN-ACCESS read-only
DESCRIPTION
"This object is not required by implementations that
are not capable of binding the send socket with a
source address. An implementation is only required to
support IPv4 and IPv6 addresses."
OBJECT traceRouteCtlSourceAddress
SYNTAX InetAddress (SIZE(0|4|16))
MIN-ACCESS read-only
DESCRIPTION
"This object is not required by implementations that
are not capable of binding the send socket with a
source address. An implementation is only required to
support IPv4 and globally unique IPv6 addresses."
OBJECT traceRouteCtlIfIndex
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. When write access is
not supported, return a 0 as the value of this object.
A value of 0 implies that the function represented by
this option is not supported."
OBJECT traceRouteCtlMiscOptions
MIN-ACCESS read-only
DESCRIPTION
"Support of this object is optional. When not
supporting, do not allow write access, and return a
zero-length octet string as the value of the object."
OBJECT traceRouteCtlStorageType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. It is also allowed
that implementations support only the volatile
StorageType enumeration."
OBJECT traceRouteCtlDSField
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. When write access is
not supported, return a 0 as the value of this object.
A value of 0 implies that the function represented by
this option is not supported."
OBJECT traceRouteCtlType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required. In addition, the only
value that is RECOMMENDED to be supported by an
implementation is traceRouteUsingUdpProbes."
OBJECT traceRouteResultsIpTgtAddrType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation should only support IPv4 and
globally unique IPv6 address values for this object."
OBJECT traceRouteResultsIpTgtAddr
SYNTAX InetAddress (SIZE(0|4|16))
DESCRIPTION
"An implementation should only support IPv4 and
globally unique IPv6 address values for this object."
OBJECT traceRouteProbeHistoryHAddrType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation should only support IPv4 and
globally unique IPv6 address values for this object."
OBJECT traceRouteProbeHistoryHAddr
SYNTAX InetAddress (SIZE(0|4|16))
DESCRIPTION
"An implementation should only support IPv4 and
globally unique IPv6 address values for this object."
OBJECT traceRouteHopsIpTgtAddressType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation should only support IPv4 and
globally unique IPv6 address values for this object."
OBJECT traceRouteHopsIpTgtAddress
SYNTAX InetAddress (SIZE(0|4|16))
DESCRIPTION
"An implementation should only support IPv4 and
globally unique IPv6 address values for this object."
::= { traceRouteCompliances 1 }
-- MIB groupings
traceRouteMinimumGroup OBJECT-GROUP
OBJECTS {
traceRouteMaxConcurrentRequests,
traceRouteCtlTargetAddressType,
traceRouteCtlTargetAddress,
traceRouteCtlByPassRouteTable,
traceRouteCtlDataSize,
traceRouteCtlTimeOut,
traceRouteCtlProbesPerHop,
traceRouteCtlPort,
traceRouteCtlMaxTtl,
traceRouteCtlDSField,
traceRouteCtlSourceAddressType,
traceRouteCtlSourceAddress,
traceRouteCtlIfIndex,
traceRouteCtlMiscOptions,
traceRouteCtlMaxFailures,
traceRouteCtlDontFragment,
traceRouteCtlInitialTtl,
traceRouteCtlFrequency,
traceRouteCtlStorageType,
traceRouteCtlAdminStatus,
traceRouteCtlMaxRows,
traceRouteCtlTrapGeneration,
traceRouteCtlDescr,
traceRouteCtlCreateHopsEntries,
traceRouteCtlType,
traceRouteResultsOperStatus,
traceRouteResultsCurHopCount,
traceRouteResultsCurProbeCount,
traceRouteResultsIpTgtAddrType,
traceRouteResultsIpTgtAddr,
traceRouteResultsTestAttempts,
traceRouteResultsTestSuccesses,
traceRouteResultsLastGoodPath
}
STATUS current
DESCRIPTION
"The group of objects that constitute the remote traceroute
operation."
::= { traceRouteGroups 5 }
traceRouteCtlRowStatusGroup OBJECT-GROUP
OBJECTS {
traceRouteCtlRowStatus
}
STATUS current
DESCRIPTION
"The RowStatus object of the traceRouteCtlTable."
::= { traceRouteGroups 6 }
traceRouteHistoryGroup OBJECT-GROUP
OBJECTS {
traceRouteProbeHistoryHAddrType,
traceRouteProbeHistoryHAddr,
traceRouteProbeHistoryResponse,
traceRouteProbeHistoryStatus,
traceRouteProbeHistoryLastRC,
traceRouteProbeHistoryTime
}
STATUS current
DESCRIPTION
"The group of objects that constitute the history
capability."
::= { traceRouteGroups 7 }
traceRouteNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS {
traceRoutePathChange,
traceRouteTestFailed,
traceRouteTestCompleted
}
STATUS current
DESCRIPTION
"The notifications that are required to be supported by
implementations of this MIB."
::= { traceRouteGroups 3 }
traceRouteHopsTableGroup OBJECT-GROUP
OBJECTS {
traceRouteHopsIpTgtAddressType,
traceRouteHopsIpTgtAddress,
traceRouteHopsMinRtt,
traceRouteHopsMaxRtt,
traceRouteHopsAverageRtt,
traceRouteHopsRttSumOfSquares,
traceRouteHopsSentProbes,
traceRouteHopsProbeResponses,
traceRouteHopsLastGoodProbe
}
STATUS current
DESCRIPTION
"The group of objects that constitute the
traceRouteHopsTable."
::= { traceRouteGroups 4 }
traceRouteGroup OBJECT-GROUP
OBJECTS {
traceRouteMaxConcurrentRequests,
traceRouteCtlTargetAddressType,
traceRouteCtlTargetAddress,
traceRouteCtlByPassRouteTable,
traceRouteCtlDataSize,
traceRouteCtlTimeOut,
traceRouteCtlProbesPerHop,
traceRouteCtlPort,
traceRouteCtlMaxTtl,
traceRouteCtlDSField,
traceRouteCtlSourceAddressType,
traceRouteCtlSourceAddress,
traceRouteCtlIfIndex,
traceRouteCtlMiscOptions,
traceRouteCtlMaxFailures,
traceRouteCtlDontFragment,
traceRouteCtlInitialTtl,
traceRouteCtlFrequency,
traceRouteCtlStorageType,
traceRouteCtlAdminStatus,
traceRouteCtlMaxRows,
traceRouteCtlTrapGeneration,
traceRouteCtlDescr,
traceRouteCtlCreateHopsEntries,
traceRouteCtlType,
traceRouteCtlRowStatus,
traceRouteResultsOperStatus,
traceRouteResultsCurHopCount,
traceRouteResultsCurProbeCount,
traceRouteResultsIpTgtAddrType,
traceRouteResultsIpTgtAddr,
traceRouteResultsTestAttempts,
traceRouteResultsTestSuccesses,
traceRouteProbeHistoryHAddrType,
traceRouteProbeHistoryHAddr,
traceRouteProbeHistoryResponse,
traceRouteProbeHistoryStatus,
traceRouteProbeHistoryLastRC
}
STATUS deprecated
DESCRIPTION
"The group of objects that constitute the remote traceroute
operation."
::= { traceRouteGroups 1 }
traceRouteTimeStampGroup OBJECT-GROUP
OBJECTS {
traceRouteResultsLastGoodPath,
traceRouteProbeHistoryTime
}
STATUS deprecated
DESCRIPTION
"The group of DateAndTime objects."
::= { traceRouteGroups 2 }
END
-- ===========================================================================
-- Full Copyright Statement
--
-- Copyright (C) The Internet Society (2004). This document is subject
-- to the rights, licenses and restrictions contained in BCP 78, and
-- except as set forth therein, the authors retain all their rights.
--
-- This document and the information contained herein are provided on an
-- "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
-- OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
-- ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
-- INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
-- INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
-- WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
--
-- Intellectual Property
--
-- The IETF takes no position regarding the validity or scope of any
-- Intellectual Property Rights or other rights that might be claimed to
-- pertain to the implementation or use of the technology described in
-- this document or the extent to which any license under such rights
-- might or might not be available; nor does it represent that it has
-- made any independent effort to identify any such rights. Information
-- on the procedures with respect to rights in RFC documents can be
-- found in BCP 78 and BCP 79.
--
-- Copies of IPR disclosures made to the IETF Secretariat and any
-- assurances of licenses to be made available, or the result of an
-- attempt made to obtain a general license or permission for the use of
-- such proprietary rights by implementers or users of this
-- specification can be obtained from the IETF on-line IPR repository at
-- http://www.ietf.org/ipr.
--
-- The IETF invites any interested party to bring to its attention any
-- copyrights, patents or patent applications, or other proprietary
-- rights that may cover technology that may be required to implement
-- this standard. Please address the information to the IETF at ietf-
-- ipr@ietf.org.
--
-- Acknowledgement
--
-- Funding for the RFC Editor function is currently provided by the
-- Internet Society.
-- ===========================================================================