compass-core/mibs/MPLS-LDP-STD-MIB.mib

2406 lines
92 KiB
Plaintext

-- =================================================================
-- Description: MPLS-LDP-STD-MIB
-- Reference: This mib was extracted from RFC 3815
-- =================================================================
MPLS-LDP-STD-MIB DEFINITIONS ::= BEGIN
IMPORTS
OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE,
Integer32, Counter32, Unsigned32
FROM SNMPv2-SMI -- [RFC2578]
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF -- [RFC2580]
RowStatus, TimeInterval, TruthValue,
TimeStamp, StorageType
FROM SNMPv2-TC -- [RFC2579]
InetAddressPrefixLength,
InetAddressType,
InetAddress,
InetPortNumber
FROM INET-ADDRESS-MIB -- [RFC3291]
IndexInteger,
IndexIntegerNextFree
FROM DIFFSERV-MIB -- [RFC3289]
mplsStdMIB,
MplsLabelDistributionMethod,
MplsLdpIdentifier,
MplsLdpLabelType,
MplsLspType,
MplsLsrIdentifier,
MplsRetentionMode
FROM MPLS-TC-STD-MIB -- [RFC3811]
MplsIndexType
FROM MPLS-LSR-STD-MIB; -- [RFC3813]
mplsLdpStdMIB MODULE-IDENTITY
LAST-UPDATED "200406030000Z" -- June 3, 2004
ORGANIZATION "Multiprotocol Label Switching (mpls)
Working Group"
CONTACT-INFO
"Joan Cucchiara (jcucchiara@mindspring.com)
Marconi Communications, Inc.
Hans Sjostrand (hans@ipunplugged.com)
ipUnplugged
James V. Luciani (james_luciani@mindspring.com)
Marconi Communications, Inc.
Working Group Chairs:
George Swallow, email: swallow@cisco.com
Loa Andersson, email: loa@pi.se
MPLS Working Group, email: mpls@uu.net"
DESCRIPTION
"Copyright (C) The Internet Society (2004). The
initial version of this MIB module was published
in RFC 3815. For full legal notices see the RFC
itself or see:
http://www.ietf.org/copyrights/ianamib.html
This MIB contains managed object definitions for the
'Multiprotocol Label Switching, Label Distribution
Protocol, LDP' document."
REVISION "200406030000Z" -- June 3, 2004
DESCRIPTION
"Initial version published as part of RFC 3815."
::= { mplsStdMIB 4 }
--****************************************************************
mplsLdpNotifications OBJECT IDENTIFIER ::= { mplsLdpStdMIB 0 }
mplsLdpObjects OBJECT IDENTIFIER ::= { mplsLdpStdMIB 1 }
mplsLdpConformance OBJECT IDENTIFIER ::= { mplsLdpStdMIB 2 }
--****************************************************************
-- MPLS LDP Objects
--****************************************************************
mplsLdpLsrObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 1 }
mplsLdpEntityObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 2 }
--
-- The MPLS Label Distribution Protocol's
-- Label Switching Router Objects
--
mplsLdpLsrId OBJECT-TYPE
SYNTAX MplsLsrIdentifier
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Label Switching Router's Identifier."
::= { mplsLdpLsrObjects 1 }
mplsLdpLsrLoopDetectionCapable OBJECT-TYPE
SYNTAX INTEGER {
none(1),
other(2),
hopCount(3),
pathVector(4),
hopCountAndPathVector(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A indication of whether this
Label Switching Router supports
loop detection.
none(1) -- Loop Detection is not supported
on this LSR.
other(2) -- Loop Detection is supported but
by a method other than those
listed below.
hopCount(3) -- Loop Detection is supported by
Hop Count only.
pathVector(4) -- Loop Detection is supported by
Path Vector only.
hopCountAndPathVector(5) -- Loop Detection is
supported by both Hop Count
And Path Vector.
Since Loop Detection is determined during
Session Initialization, an individual session
may not be running with loop detection. This
object simply gives an indication of whether or not the
LSR has the ability to support Loop Detection and
which types."
::= { mplsLdpLsrObjects 2 }
--
-- The MPLS Label Distribution Protocol Entity Objects
--
mplsLdpEntityLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time of the most
recent addition or deletion of an entry
to/from the mplsLdpEntityTable/mplsLdpEntityStatsTable, or
the most recent change in value of any objects in the
mplsLdpEntityTable.
If no such changes have occurred since the last
re-initialization of the local management subsystem,
then this object contains a zero value."
::= { mplsLdpEntityObjects 1 }
mplsLdpEntityIndexNext OBJECT-TYPE
SYNTAX IndexIntegerNextFree
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains an appropriate value to
be used for mplsLdpEntityIndex when creating
entries in the mplsLdpEntityTable. The value
0 indicates that no unassigned entries are
available."
::= { mplsLdpEntityObjects 2 }
mplsLdpEntityTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpEntityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information about the
MPLS Label Distribution Protocol Entities which
exist on this Label Switching Router (LSR)
or Label Edge Router (LER)."
::= { mplsLdpEntityObjects 3 }
mplsLdpEntityEntry OBJECT-TYPE
SYNTAX MplsLdpEntityEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents an LDP entity.
An entry can be created by a network administrator
or by an SNMP agent as instructed by LDP."
INDEX { mplsLdpEntityLdpId, mplsLdpEntityIndex }
::= { mplsLdpEntityTable 1 }
MplsLdpEntityEntry ::= SEQUENCE {
mplsLdpEntityLdpId MplsLdpIdentifier,
mplsLdpEntityIndex IndexInteger,
mplsLdpEntityProtocolVersion Unsigned32,
mplsLdpEntityAdminStatus INTEGER,
mplsLdpEntityOperStatus INTEGER,
mplsLdpEntityTcpPort InetPortNumber,
mplsLdpEntityUdpDscPort InetPortNumber,
mplsLdpEntityMaxPduLength Unsigned32,
mplsLdpEntityKeepAliveHoldTimer Unsigned32,
mplsLdpEntityHelloHoldTimer Unsigned32,
mplsLdpEntityInitSessionThreshold Integer32,
mplsLdpEntityLabelDistMethod MplsLabelDistributionMethod,
mplsLdpEntityLabelRetentionMode MplsRetentionMode,
mplsLdpEntityPathVectorLimit Integer32,
mplsLdpEntityHopCountLimit Integer32,
mplsLdpEntityTransportAddrKind INTEGER,
mplsLdpEntityTargetPeer TruthValue,
mplsLdpEntityTargetPeerAddrType InetAddressType,
mplsLdpEntityTargetPeerAddr InetAddress,
mplsLdpEntityLabelType MplsLdpLabelType,
mplsLdpEntityDiscontinuityTime TimeStamp,
mplsLdpEntityStorageType StorageType,
mplsLdpEntityRowStatus RowStatus
}
mplsLdpEntityLdpId OBJECT-TYPE
SYNTAX MplsLdpIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The LDP identifier."
REFERENCE
"RFC3036, LDP Specification, Section on LDP Identifiers."
::= { mplsLdpEntityEntry 1 }
mplsLdpEntityIndex OBJECT-TYPE
SYNTAX IndexInteger
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This index is used as a secondary index to uniquely
identify this row. Before creating a row in this table,
the 'mplsLdpEntityIndexNext' object should be retrieved.
That value should be used for the value of this index
when creating a row in this table. NOTE: if a value
of zero (0) is retrieved, that indicates that no rows
can be created in this table at this time.
A secondary index (this object) is meaningful to some
but not all, LDP implementations. For example
an LDP implementation which uses PPP would
use this index to differentiate PPP sub-links.
Another way to use this index is to give this the
value of ifIndex. However, this is dependant
on the implementation."
::= { mplsLdpEntityEntry 2 }
mplsLdpEntityProtocolVersion OBJECT-TYPE
SYNTAX Unsigned32(1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The version number of the LDP protocol which will be
used in the session initialization message.
Section 3.5.3 in the LDP Specification specifies
that the version of the LDP protocol is negotiated during
session establishment. The value of this object
represents the value that is sent in the initialization
message."
REFERENCE
"RFC3036, LDP Specification, Section 3.5.3 Initialization
Message."
DEFVAL { 1 }
::= { mplsLdpEntityEntry 3 }
mplsLdpEntityAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
enable(1),
disable(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The administrative status of this LDP Entity.
If this object is changed from 'enable' to 'disable'
and this entity has already attempted to establish
contact with a Peer, then all contact with that
Peer is lost and all information from that Peer
needs to be removed from the MIB. (This implies
that the network management subsystem should clean
up any related entry in the mplsLdpPeerTable. This
further implies that a 'tear-down' for that session
is issued and the session and all information related
to that session cease to exist).
At this point the operator is able to change values
which are related to this entity.
When the admin status is set back to 'enable', then
this Entity will attempt to establish a new session
with the Peer."
DEFVAL { enable }
::= { mplsLdpEntityEntry 4 }
mplsLdpEntityOperStatus OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
enabled(2),
disabled(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The operational status of this LDP Entity.
The value of unknown(1) indicates that the
operational status cannot be determined at
this time. The value of unknown should be
a transient condition before changing
to enabled(2) or disabled(3)."
::= { mplsLdpEntityEntry 5 }
mplsLdpEntityTcpPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The TCP Port for
LDP. The default value is the well-known
value of this port."
REFERENCE
"RFC3036, LDP Specification, Section 3.10, Well-known
Numbers, and Section 3.10.1. UDP and TCP Ports."
DEFVAL { 646 }
::= { mplsLdpEntityEntry 6 }
mplsLdpEntityUdpDscPort OBJECT-TYPE
SYNTAX InetPortNumber
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The UDP Discovery Port for
LDP. The default value is the
well-known value for this port."
REFERENCE
"RFC3036, LDP Specification, Section 2.4.1,
Basic Discovery Mechanism, Section 2.4.2,
Extended Discovery Mechanism, Section
3.10, Well-known Numbers, and Section 3.10.1.
UDP and TCP Ports."
DEFVAL { 646 }
::= { mplsLdpEntityEntry 7 }
mplsLdpEntityMaxPduLength OBJECT-TYPE
SYNTAX Unsigned32 (256..65535)
UNITS "octets"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum PDU Length that is sent in
the Common Session Parameters of an Initialization
Message. According to the LDP Specification [RFC3036]
a value of 255 or less specifies the
default maximum length of 4096 octets, this is why
the value of this object starts at 256. The operator
should explicitly choose the default value (i.e., 4096),
or some other value.
The receiving LSR MUST calculate the maximum PDU
length for the session by using the smaller of its and
its peer's proposals for Max PDU Length."
REFERENCE
"RFC3036, LDP Specification, Section 3.5.3.
Initialization Message."
DEFVAL { 4096 }
::= { mplsLdpEntityEntry 8 }
mplsLdpEntityKeepAliveHoldTimer OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The 16-bit integer value which is the proposed keep
alive hold timer for this LDP Entity."
DEFVAL { 40 }
::= { mplsLdpEntityEntry 9 }
mplsLdpEntityHelloHoldTimer OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The 16-bit integer value which is the proposed Hello
hold timer for this LDP Entity. The Hello Hold time
in seconds.
An LSR maintains a record of Hellos received
from potential peers. This object represents
the Hold Time in the Common Hello Parameters TLV of
the Hello Message.
A value of 0 is a default value and should be
interpretted in conjunction with the
mplsLdpEntityTargetPeer object.
If the value of this object is 0: if the value of the
mplsLdpEntityTargetPeer object is false(2), then this
specifies that the Hold Time's actual default value is
15 seconds (i.e., the default Hold time for Link Hellos
is 15 seconds). Otherwise if the value of the
mplsLdpEntityTargetPeer object is true(1), then this
specifies that the Hold Time's actual default value is
45 seconds (i.e., the default Hold time for Targeted
Hellos is 45 seconds).
A value of 65535 means infinite (i.e., wait forever).
All other values represent the amount of time in
seconds to wait for a Hello Message. Setting the
hold time to a value smaller than 15 is not
recommended, although not forbidden according
to RFC3036."
REFERENCE
"RFC3036, LDP Specification, Section 3.5.2.,
Hello Message."
DEFVAL { 0 }
::= { mplsLdpEntityEntry 10 }
mplsLdpEntityInitSessionThreshold OBJECT-TYPE
SYNTAX Integer32(0..100)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"When attempting to establish a session with
a given Peer, the given LDP Entity should
send out the SNMP notification,
'mplsLdpInitSessionThresholdExceeded', when
the number of Session Initialization messages
sent exceeds this threshold.
The notification is used to notify an
operator when this Entity and its Peer are
possibly engaged in an endless sequence
of messages as each NAKs the other's
Initialization messages with Error Notification
messages. Setting this threshold which triggers
the notification is one way to notify the
operator. The notification should be generated
each time this threshold is exceeded and
for every subsequent Initialization message
which is NAK'd with an Error Notification
message after this threshold is exceeded.
A value of 0 (zero) for this object
indicates that the threshold is infinity, thus
the SNMP notification will never be generated."
REFERENCE
"RFC3036, LDP Specification,
Section 2.5.3 Session Initialization."
DEFVAL { 8 }
::= { mplsLdpEntityEntry 11 }
mplsLdpEntityLabelDistMethod OBJECT-TYPE
SYNTAX MplsLabelDistributionMethod
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"For any given LDP session, the method of
label distribution must be specified."
::= { mplsLdpEntityEntry 12 }
mplsLdpEntityLabelRetentionMode OBJECT-TYPE
SYNTAX MplsRetentionMode
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The LDP Entity can be configured to use either
conservative or liberal label retention mode.
If the value of this object is conservative(1)
then advertized label mappings are retained
only if they will be used to forward packets,
i.e., if label came from a valid next hop.
If the value of this object is liberal(2)
then all advertized label mappings are retained
whether they are from a valid next hop or not."
::= { mplsLdpEntityEntry 13 }
mplsLdpEntityPathVectorLimit OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the value of this object is 0 (zero) then
Loop Detection for Path Vectors is disabled.
Otherwise, if this object has a value greater than
zero, then Loop Dection for Path Vectors is enabled,
and the Path Vector Limit is this value.
Also, the value of the object,
'mplsLdpLsrLoopDetectionCapable', must be set to
either 'pathVector(4)' or 'hopCountAndPathVector(5)',
if this object has a value greater than 0 (zero),
otherwise it is ignored."
REFERENCE
"RFC3036, LDP Specification, Section 2.8 Loop Dection,
Section 3.4.5 Path Vector TLV."
::= { mplsLdpEntityEntry 14 }
mplsLdpEntityHopCountLimit OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the value of this object is 0 (zero),
then Loop Detection using Hop Counters is
disabled.
If the value of this object is greater than
0 (zero) then Loop Detection using Hop
Counters is enabled, and this object
specifies this Entity's maximum allowable
value for the Hop Count.
Also, the value of the object
mplsLdpLsrLoopDetectionCapable must be set
to either 'hopCount(3)' or
'hopCountAndPathVector(5)' if this object
has a value greater than 0 (zero), otherwise
it is ignored."
DEFVAL { 0 }
::= { mplsLdpEntityEntry 15 }
mplsLdpEntityTransportAddrKind OBJECT-TYPE
SYNTAX INTEGER {
interface(1),
loopback(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This specifies whether the loopback or interface
address is to be used as the transport address
in the transport address TLV of the
hello message.
If the value is interface(1), then the IP
address of the interface from which hello
messages are sent is used as the transport
address in the hello message.
Otherwise, if the value is loopback(2), then the IP
address of the loopback interface is used as the
transport address in the hello message."
DEFVAL { loopback }
::= { mplsLdpEntityEntry 16 }
mplsLdpEntityTargetPeer OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If this LDP entity uses targeted peer then set
this to true."
DEFVAL { false }
::= { mplsLdpEntityEntry 17 }
mplsLdpEntityTargetPeerAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the internetwork layer address used for
the Extended Discovery. This object indicates how
the value of mplsLdpEntityTargetPeerAddr is to
be interpreted."
::= { mplsLdpEntityEntry 18 }
mplsLdpEntityTargetPeerAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of the internetwork layer address
used for the Extended Discovery. The value of
mplsLdpEntityTargetPeerAddrType specifies how
this address is to be interpreted."
::= { mplsLdpEntityEntry 19 }
mplsLdpEntityLabelType OBJECT-TYPE
SYNTAX MplsLdpLabelType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the optional parameters for the LDP
Initialization Message.
If the value is generic(1) then no
optional parameters will be sent in
the LDP Initialization message associated
with this Entity.
If the value is atmParameters(2) then
a row must be created in the
mplsLdpEntityAtmTable, which
corresponds to this entry.
If the value is frameRelayParameters(3) then
a row must be created in the
mplsLdpEntityFrameRelayTable, which
corresponds to this entry."
REFERENCE
"RFC3036, LDP Specification, Section 3.5.3.,
Initialization Message."
::= { mplsLdpEntityEntry 20 }
mplsLdpEntityDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion
at which any one or more of this entity's counters
suffered a discontinuity. The relevant counters
are the specific instances associated with this
entity of any Counter32 object contained
in the 'mplsLdpEntityStatsTable'. If no such
discontinuities have occurred since the last
re-initialization of the local management
subsystem, then this object contains a zero
value."
::= { mplsLdpEntityEntry 21 }
mplsLdpEntityStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this conceptual row.
Conceptual rows having the value 'permanent(4)'
need not allow write-access to any columnar
objects in the row."
DEFVAL{ nonVolatile }
::= { mplsLdpEntityEntry 22 }
mplsLdpEntityRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. All writable
objects in this row may be modified at any
time, however, as described in detail in
the section entitled, 'Changing Values After
Session Establishment', and again described
in the DESCRIPTION clause of the
mplsLdpEntityAdminStatus object, if a session
has been initiated with a Peer, changing objects
in this table will wreak havoc with the session
and interrupt traffic. To repeat again:
the recommended procedure is to
set the mplsLdpEntityAdminStatus to down, thereby
explicitly causing a session to be torn down. Then,
change objects in this entry, then set
the mplsLdpEntityAdminStatus to enable,
which enables a new session to be initiated."
::= { mplsLdpEntityEntry 23 }
--
-- The MPLS LDP Entity Statistics Table
--
mplsLdpEntityStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpEntityStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is a read-only table which augments
the mplsLdpEntityTable. The purpose of this
table is to keep statistical information about
the LDP Entities on the LSR."
::= { mplsLdpEntityObjects 4 }
mplsLdpEntityStatsEntry OBJECT-TYPE
SYNTAX MplsLdpEntityStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A row in this table contains statistical information
about an LDP Entity. Some counters contained in a
row are for fatal errors received during a former
LDP Session associated with this entry. For example,
an LDP PDU received on a TCP connection during an
LDP Session contains a fatal error. That
error is counted here, because the
session is terminated.
If the error is NOT fatal (i.e., the Session
remains), then the error is counted in the
mplsLdpSessionStatsEntry."
AUGMENTS { mplsLdpEntityEntry }
::= { mplsLdpEntityStatsTable 1 }
MplsLdpEntityStatsEntry ::= SEQUENCE {
mplsLdpEntityStatsSessionAttempts Counter32,
mplsLdpEntityStatsSessionRejectedNoHelloErrors Counter32,
mplsLdpEntityStatsSessionRejectedAdErrors Counter32,
mplsLdpEntityStatsSessionRejectedMaxPduErrors Counter32,
mplsLdpEntityStatsSessionRejectedLRErrors Counter32,
mplsLdpEntityStatsBadLdpIdentifierErrors Counter32,
mplsLdpEntityStatsBadPduLengthErrors Counter32,
mplsLdpEntityStatsBadMessageLengthErrors Counter32,
mplsLdpEntityStatsBadTlvLengthErrors Counter32,
mplsLdpEntityStatsMalformedTlvValueErrors Counter32,
mplsLdpEntityStatsKeepAliveTimerExpErrors Counter32,
mplsLdpEntityStatsShutdownReceivedNotifications Counter32,
mplsLdpEntityStatsShutdownSentNotifications Counter32
}
mplsLdpEntityStatsSessionAttempts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the Session Initialization messages
which were sent or received by this LDP Entity and
were NAK'd. In other words, this counter counts
the number of session initializations that failed.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
mplsLdpEntityDiscontinuityTime."
::= { mplsLdpEntityStatsEntry 1 }
mplsLdpEntityStatsSessionRejectedNoHelloErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the Session Rejected/No Hello Error
Notification Messages sent or received by
this LDP Entity.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
mplsLdpEntityDiscontinuityTime."
::= { mplsLdpEntityStatsEntry 2 }
mplsLdpEntityStatsSessionRejectedAdErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the Session Rejected/Parameters
Advertisement Mode Error Notification Messages sent
or received by this LDP Entity.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
mplsLdpEntityDiscontinuityTime."
::= { mplsLdpEntityStatsEntry 3 }
mplsLdpEntityStatsSessionRejectedMaxPduErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the Session Rejected/Parameters
Max Pdu Length Error Notification Messages sent
or received by this LDP Entity.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
mplsLdpEntityDiscontinuityTime."
::= { mplsLdpEntityStatsEntry 4 }
mplsLdpEntityStatsSessionRejectedLRErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A count of the Session Rejected/Parameters
Label Range Notification Messages sent
or received by this LDP Entity.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
mplsLdpEntityDiscontinuityTime."
::= { mplsLdpEntityStatsEntry 5 }
mplsLdpEntityStatsBadLdpIdentifierErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Bad LDP Identifier
Fatal Errors detected by the session(s)
(past and present) associated with this LDP Entity.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
mplsLdpEntityDiscontinuityTime."
REFERENCE
"RFC3036, LDP Specification, Section 3.5.1.2."
::= { mplsLdpEntityStatsEntry 6 }
mplsLdpEntityStatsBadPduLengthErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Bad PDU Length
Fatal Errors detected by the session(s)
(past and present) associated with this LDP Entity.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
mplsLdpEntityDiscontinuityTime."
REFERENCE
"RFC3036, LDP Specification, Section 3.5.1.2."
::= { mplsLdpEntityStatsEntry 7 }
mplsLdpEntityStatsBadMessageLengthErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Bad Message
Length Fatal Errors detected by the session(s)
(past and present) associated with this LDP Entity.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
mplsLdpEntityDiscontinuityTime."
REFERENCE
"RFC3036, LDP Specification, Section 3.5.1.2."
::= { mplsLdpEntityStatsEntry 8 }
mplsLdpEntityStatsBadTlvLengthErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Bad TLV
Length Fatal Errors detected by the session(s)
(past and present) associated with this LDP Entity.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
mplsLdpEntityDiscontinuityTime."
REFERENCE
"RFC3036, LDP Specification, Section 3.5.1.2."
::= { mplsLdpEntityStatsEntry 9 }
mplsLdpEntityStatsMalformedTlvValueErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Malformed TLV
Value Fatal Errors detected by the session(s)
(past and present) associated with this
LDP Entity.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
mplsLdpEntityDiscontinuityTime."
REFERENCE
"RFC3036, LDP Specification, Section 3.5.1.2."
::= { mplsLdpEntityStatsEntry 10 }
mplsLdpEntityStatsKeepAliveTimerExpErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Session Keep Alive
Timer Expired Errors detected by the session(s)
(past and present) associated with this LDP Entity.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
mplsLdpEntityDiscontinuityTime."
REFERENCE
"RFC3036, LDP Specification, Section 3.5.1.2."
::= { mplsLdpEntityStatsEntry 11 }
mplsLdpEntityStatsShutdownReceivedNotifications OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Shutdown Notifications
received related to session(s) (past and present)
associated with this LDP Entity.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
mplsLdpEntityDiscontinuityTime."
::= { mplsLdpEntityStatsEntry 12 }
mplsLdpEntityStatsShutdownSentNotifications OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Shutdown Notfications
sent related to session(s) (past and present) associated
with this LDP Entity.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
mplsLdpEntityDiscontinuityTime."
::= { mplsLdpEntityStatsEntry 13 }
--
-- The MPLS LDP Peer Table
--
mplsLdpSessionObjects OBJECT IDENTIFIER ::= { mplsLdpObjects 3 }
mplsLdpPeerLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time of the most
recent addition or deletion to/from the
mplsLdpPeerTable/mplsLdpSessionTable."
::= { mplsLdpSessionObjects 1 }
mplsLdpPeerTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about LDP peers known by Entities in
the mplsLdpEntityTable. The information in this table
is based on information from the Entity-Peer interaction
during session initialization but is not appropriate
for the mplsLdpSessionTable, because objects in this
table may or may not be used in session establishment."
::= { mplsLdpSessionObjects 2 }
mplsLdpPeerEntry OBJECT-TYPE
SYNTAX MplsLdpPeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about a single Peer which is related
to a Session. This table is augmented by
the mplsLdpSessionTable."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpPeerLdpId }
::= { mplsLdpPeerTable 1 }
MplsLdpPeerEntry ::= SEQUENCE {
mplsLdpPeerLdpId MplsLdpIdentifier,
mplsLdpPeerLabelDistMethod MplsLabelDistributionMethod,
mplsLdpPeerPathVectorLimit Integer32,
mplsLdpPeerTransportAddrType InetAddressType,
mplsLdpPeerTransportAddr InetAddress
}
mplsLdpPeerLdpId OBJECT-TYPE
SYNTAX MplsLdpIdentifier
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The LDP identifier of this LDP Peer."
::= { mplsLdpPeerEntry 1 }
mplsLdpPeerLabelDistMethod OBJECT-TYPE
SYNTAX MplsLabelDistributionMethod
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For any given LDP session, the method of
label distribution must be specified."
::= { mplsLdpPeerEntry 2 }
mplsLdpPeerPathVectorLimit OBJECT-TYPE
SYNTAX Integer32 (0..255)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the value of this object is 0 (zero) then
Loop Dection for Path Vectors for this Peer
is disabled.
Otherwise, if this object has a value greater than
zero, then Loop Dection for Path Vectors for this
Peer is enabled and the Path Vector Limit is this value."
REFERENCE
"RFC3036, LDP Specification, Section 2.8 Loop Dection,
Section 3.4.5 Path Vector TLV."
::= { mplsLdpPeerEntry 3 }
mplsLdpPeerTransportAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of the Internet address for the
mplsLdpPeerTransportAddr object. The LDP
specification describes this as being either
an IPv4 Transport Address or IPv6 Transport
Address which is used in opening the LDP session's
TCP connection, or if the optional TLV is not
present, then this is the IPv4/IPv6 source
address for the UPD packet carrying the Hellos.
This object specifies how the value of the
mplsLdpPeerTransportAddr object should be
interpreted."
REFERENCE
"RFC3036, LDP Specification, Section 2.5.2
Transport Connection Establishment and
Section 3.5.2.1 Hello Message Procedures."
::= { mplsLdpPeerEntry 4 }
mplsLdpPeerTransportAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Internet address advertised by the peer
in the Hello Message or the Hello source address.
The type of this address is specified by the
value of the mplsLdpPeerTransportAddrType
object."
REFERENCE
"RFC3036, LDP Specification, Section 2.5.2
Transport Connection Establishment and
Section 3.5.2.1 Hello Message Procedures."
::= { mplsLdpPeerEntry 5 }
--
-- The MPLS LDP Sessions Table
--
mplsLdpSessionTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpSessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of Sessions between the LDP Entities
and LDP Peers. This table AUGMENTS the
mplsLdpPeerTable. Each row in this table
represents a single session."
::= { mplsLdpSessionObjects 3 }
mplsLdpSessionEntry OBJECT-TYPE
SYNTAX MplsLdpSessionEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents information on a
single session between an LDP Entity and LDP Peer.
The information contained in a row is read-only.
Please note: the Path Vector Limit for the
Session is the value which is configured in
the corresponding mplsLdpEntityEntry. The
Peer's Path Vector Limit is in the
mplsLdpPeerPathVectorLimit object in the
mplsLdpPeerTable.
Values which may differ from those configured are
noted in the objects of this table, the
mplsLdpAtmSessionTable and the
mplsLdpFrameRelaySessionTable. A value will
differ if it was negotiated between the
Entity and the Peer. Values may or may not
be negotiated. For example, if the values
are the same then no negotiation takes place.
If they are negotiated, then they may differ."
AUGMENTS { mplsLdpPeerEntry }
::= { mplsLdpSessionTable 1 }
MplsLdpSessionEntry ::= SEQUENCE {
mplsLdpSessionStateLastChange TimeStamp,
mplsLdpSessionState INTEGER,
mplsLdpSessionRole INTEGER,
mplsLdpSessionProtocolVersion Unsigned32,
mplsLdpSessionKeepAliveHoldTimeRem TimeInterval,
mplsLdpSessionKeepAliveTime Unsigned32,
mplsLdpSessionMaxPduLength Unsigned32,
mplsLdpSessionDiscontinuityTime TimeStamp
}
mplsLdpSessionStateLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time this
Session entered its current state as
denoted by the mplsLdpSessionState
object."
::= { mplsLdpSessionEntry 1 }
mplsLdpSessionState OBJECT-TYPE
SYNTAX INTEGER {
nonexistent(1),
initialized(2),
openrec(3),
opensent(4),
operational(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current state of the session, all of the
states 1 to 5 are based on the state machine
for session negotiation behavior."
REFERENCE
"RFC3036, LDP Specification, Section 2.5.4,
Initialization State Machine."
::= { mplsLdpSessionEntry 2 }
mplsLdpSessionRole OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
active(2),
passive(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"During session establishment the LSR/LER takes either
the active role or the passive role based on address
comparisons. This object indicates whether this LSR/LER
was behaving in an active role or passive role during
this session's establishment.
The value of unknown(1), indicates that the role is not
able to be determined at the present time."
REFERENCE
"RFC3036, LDP Specification, Section 2.5.3.,
Session Initialization"
::= { mplsLdpSessionEntry 3 }
mplsLdpSessionProtocolVersion OBJECT-TYPE
SYNTAX Unsigned32(1..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The version of the LDP Protocol which
this session is using. This is the version of
the LDP protocol which has been negotiated
during session initialization."
REFERENCE
"RFC3036, LDP Specification, Section 3.5.3,
Initialization Message."
::= { mplsLdpSessionEntry 4 }
mplsLdpSessionKeepAliveHoldTimeRem OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The keep alive hold time remaining for
this session."
::= { mplsLdpSessionEntry 5 }
mplsLdpSessionKeepAliveTime OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The negotiated KeepAlive Time which
represents the amount of seconds between
keep alive messages. The
mplsLdpEntityKeepAliveHoldTimer
related to this Session is the
value that was proposed as the
KeepAlive Time for this session.
This value is negotiated during
session initialization between
the entity's proposed value
(i.e., the value configured in
mplsLdpEntityKeepAliveHoldTimer)
and the peer's proposed
KeepAlive Hold Timer value.
This value is the smaller
of the two proposed values."
REFERENCE
"RFC3036, LDP Specification, Section 3.5.3,
Initialization Message."
::= { mplsLdpSessionEntry 6 }
mplsLdpSessionMaxPduLength OBJECT-TYPE
SYNTAX Unsigned32 (1..65535)
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of maximum allowable length for LDP PDUs for
this session. This value may have been negotiated
during the Session Initialization. This object is
related to the mplsLdpEntityMaxPduLength object. The
mplsLdpEntityMaxPduLength object specifies the requested
LDP PDU length, and this object reflects the negotiated
LDP PDU length between the Entity and
the Peer."
REFERENCE
"RFC3036, LDP Specification, Section 3.5.3,
Initialization Message."
::= { mplsLdpSessionEntry 7 }
mplsLdpSessionDiscontinuityTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion
at which any one or more of this session's counters
suffered a discontinuity. The relevant counters are
the specific instances associated with this session
of any Counter32 object contained in the
mplsLdpSessionStatsTable.
The initial value of this object is the value of
sysUpTime when the entry was created in this table.
Also, a command generator can distinguish when a session
between a given Entity and Peer goes away and a new
session is established. This value would change and
thus indicate to the command generator that this is a
different session."
::= { mplsLdpSessionEntry 8 }
--
-- The MPLS LDP Session Statistics Table
--
mplsLdpSessionStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpSessionStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of statistics for Sessions between
LDP Entities and LDP Peers. This table AUGMENTS
the mplsLdpPeerTable."
::= { mplsLdpSessionObjects 4 }
mplsLdpSessionStatsEntry OBJECT-TYPE
SYNTAX MplsLdpSessionStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents statistical
information on a single session between an LDP
Entity and LDP Peer."
AUGMENTS { mplsLdpPeerEntry }
::= { mplsLdpSessionStatsTable 1 }
MplsLdpSessionStatsEntry ::= SEQUENCE {
mplsLdpSessionStatsUnknownMesTypeErrors Counter32,
mplsLdpSessionStatsUnknownTlvErrors Counter32
}
mplsLdpSessionStatsUnknownMesTypeErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Unknown Message Type
Errors detected by this LSR/LER during this session.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
mplsLdpSessionDiscontinuityTime."
::= { mplsLdpSessionStatsEntry 1 }
mplsLdpSessionStatsUnknownTlvErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object counts the number of Unknown TLV Errors
detected by this LSR/LER during this session.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
mplsLdpSessionDiscontinuityTime."
::= { mplsLdpSessionStatsEntry 2 }
--
-- The MPLS LDP Hello Adjacency Table
--
mplsLdpHelloAdjacencyObjects OBJECT IDENTIFIER ::=
{ mplsLdpSessionObjects 5 }
mplsLdpHelloAdjacencyTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpHelloAdjacencyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of Hello Adjacencies for Sessions."
::= { mplsLdpHelloAdjacencyObjects 1 }
mplsLdpHelloAdjacencyEntry OBJECT-TYPE
SYNTAX MplsLdpHelloAdjacencyEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each row represents a single LDP Hello Adjacency.
An LDP Session can have one or more Hello
Adjacencies."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpPeerLdpId,
mplsLdpHelloAdjacencyIndex }
::= { mplsLdpHelloAdjacencyTable 1 }
MplsLdpHelloAdjacencyEntry ::= SEQUENCE {
mplsLdpHelloAdjacencyIndex Unsigned32,
mplsLdpHelloAdjacencyHoldTimeRem TimeInterval,
mplsLdpHelloAdjacencyHoldTime Unsigned32,
mplsLdpHelloAdjacencyType INTEGER
}
mplsLdpHelloAdjacencyIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An identifier for this specific adjacency."
::= { mplsLdpHelloAdjacencyEntry 1 }
mplsLdpHelloAdjacencyHoldTimeRem OBJECT-TYPE
SYNTAX TimeInterval
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If the value of this object is 65535,
this means that the hold time is infinite
(i.e., wait forever).
Otherwise, the time remaining for
this Hello Adjacency to receive its
next Hello Message.
This interval will change when the 'next'
Hello Message which corresponds to this
Hello Adjacency is received unless it
is infinite."
::= { mplsLdpHelloAdjacencyEntry 2 }
mplsLdpHelloAdjacencyHoldTime OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Hello hold time which is negotiated between
the Entity and the Peer. The entity associated
with this Hello Adjacency issues a proposed
Hello Hold Time value in the
mplsLdpEntityHelloHoldTimer object. The peer
also proposes a value and this object represents
the negotiated value.
A value of 0 means the default,
which is 15 seconds for Link Hellos
and 45 seconds for Targeted Hellos.
A value of 65535 indicates an
infinite hold time."
REFERENCE
"RFC3036, LDP Specification, Section 3.5.2 Hello Message"
::= { mplsLdpHelloAdjacencyEntry 3 }
mplsLdpHelloAdjacencyType OBJECT-TYPE
SYNTAX INTEGER {
link(1),
targeted(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This adjacency is the result of a 'link'
hello if the value of this object is link(1).
Otherwise, it is a result of a 'targeted'
hello, targeted(2)."
::= { mplsLdpHelloAdjacencyEntry 4 }
--
-- Session Label (LSP) Mapping to LSR MIB's
-- In Segment LIB Information.
--
--
-- NOTE: the next 2 tables map to the
-- MPLS-LSR-STD-MIB's MplsInSegmentTable
-- and MplsOutSegmentTable. The
-- cross-connect (XC) information is not
-- represented here as it can be gleaned
-- from the MPLS-LSR-STD-MIB.
--
mplsInSegmentLdpLspTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsInSegmentLdpLspEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of LDP LSP's which
map to the mplsInSegmentTable in the
MPLS-LSR-STD-MIB module."
::= { mplsLdpSessionObjects 6 }
mplsInSegmentLdpLspEntry OBJECT-TYPE
SYNTAX MplsInSegmentLdpLspEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents information
on a single LDP LSP which is represented by
a session's index triple (mplsLdpEntityLdpId,
mplsLdpEntityIndex, mplsLdpPeerLdpId) AND the
index for the mplsInSegmentTable
(mplsInSegmentLdpLspLabelIndex) from the
MPLS-LSR-STD-MIB.
The information contained in a row is read-only."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpPeerLdpId,
mplsInSegmentLdpLspIndex
}
::= { mplsInSegmentLdpLspTable 1 }
MplsInSegmentLdpLspEntry ::= SEQUENCE {
mplsInSegmentLdpLspIndex MplsIndexType,
mplsInSegmentLdpLspLabelType MplsLdpLabelType,
mplsInSegmentLdpLspType MplsLspType
}
mplsInSegmentLdpLspIndex OBJECT-TYPE
SYNTAX MplsIndexType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This contains the same value as the
mplsInSegmentIndex in the
MPLS-LSR-STD-MIB's mplsInSegmentTable."
::= { mplsInSegmentLdpLspEntry 1 }
mplsInSegmentLdpLspLabelType OBJECT-TYPE
SYNTAX MplsLdpLabelType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Layer 2 Label Type."
::= { mplsInSegmentLdpLspEntry 2 }
mplsInSegmentLdpLspType OBJECT-TYPE
SYNTAX MplsLspType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of LSP connection."
::= { mplsInSegmentLdpLspEntry 3 }
--
-- Session Label (LSP) Mapping to LSR MIB's
-- Out Segment LIB Information.
--
mplsOutSegmentLdpLspTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsOutSegmentLdpLspEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table of LDP LSP's which
map to the mplsOutSegmentTable in the
MPLS-LSR-STD-MIB."
::= { mplsLdpSessionObjects 7 }
mplsOutSegmentLdpLspEntry OBJECT-TYPE
SYNTAX MplsOutSegmentLdpLspEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents information
on a single LDP LSP which is represented by
a session's index triple (mplsLdpEntityLdpId,
mplsLdpEntityIndex, mplsLdpPeerLdpId) AND the
index (mplsOutSegmentLdpLspIndex)
for the mplsOutSegmentTable.
The information contained in a row is read-only."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpPeerLdpId,
mplsOutSegmentLdpLspIndex
}
::= { mplsOutSegmentLdpLspTable 1 }
MplsOutSegmentLdpLspEntry ::= SEQUENCE {
mplsOutSegmentLdpLspIndex MplsIndexType,
mplsOutSegmentLdpLspLabelType MplsLdpLabelType,
mplsOutSegmentLdpLspType MplsLspType
}
mplsOutSegmentLdpLspIndex OBJECT-TYPE
SYNTAX MplsIndexType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This contains the same value as the
mplsOutSegmentIndex in the
MPLS-LSR-STD-MIB's mplsOutSegmentTable."
::= { mplsOutSegmentLdpLspEntry 1 }
mplsOutSegmentLdpLspLabelType OBJECT-TYPE
SYNTAX MplsLdpLabelType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Layer 2 Label Type."
::= { mplsOutSegmentLdpLspEntry 2 }
mplsOutSegmentLdpLspType OBJECT-TYPE
SYNTAX MplsLspType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of LSP connection."
::= { mplsOutSegmentLdpLspEntry 3 }
--
-- Mpls FEC Table
--
mplsFecObjects OBJECT IDENTIFIER ::=
{ mplsLdpSessionObjects 8 }
mplsFecLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time of the most
recent addition/deletion of an entry
to/from the mplsLdpFectTable or
the most recent change in values to any objects
in the mplsLdpFecTable.
If no such changes have occurred since the last
re-initialization of the local management subsystem,
then this object contains a zero value."
::= { mplsFecObjects 1 }
mplsFecIndexNext OBJECT-TYPE
SYNTAX IndexIntegerNextFree
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains an appropriate value to
be used for mplsFecIndex when creating
entries in the mplsFecTable. The value
0 indicates that no unassigned entries are
available."
::= { mplsFecObjects 2 }
mplsFecTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsFecEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table represents the FEC
(Forwarding Equivalence Class)
Information associated with an LSP."
::= { mplsFecObjects 3 }
mplsFecEntry OBJECT-TYPE
SYNTAX MplsFecEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each row represents a single FEC Element."
INDEX { mplsFecIndex }
::= { mplsFecTable 1 }
MplsFecEntry ::= SEQUENCE {
mplsFecIndex IndexInteger,
mplsFecType INTEGER,
mplsFecAddrType InetAddressType,
mplsFecAddr InetAddress,
mplsFecAddrPrefixLength InetAddressPrefixLength,
mplsFecStorageType StorageType,
mplsFecRowStatus RowStatus
}
mplsFecIndex OBJECT-TYPE
SYNTAX IndexInteger
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index which uniquely identifies this entry."
::= { mplsFecEntry 1 }
mplsFecType OBJECT-TYPE
SYNTAX INTEGER {
prefix(1),
hostAddress(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The type of the FEC. If the value of this object
is 'prefix(1)' then the FEC type described by this
row is an address prefix.
If the value of this object is 'hostAddress(2)' then
the FEC type described by this row is a host address."
REFERENCE
"RFC3036, Section 3.4.1. FEC TLV."
::= { mplsFecEntry 2 }
mplsFecAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object is the type of the
Internet address. The value of this object,
decides how the value of the mplsFecAddr object
is interpreted."
REFERENCE
"RFC3036, Section 3.4.1. FEC TLV."
::= { mplsFecEntry 4 }
mplsFecAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object is interpreted based
on the value of the 'mplsFecAddrType' object.
This address is then further interpretted as
an being used with the address prefix,
or as the host address. This further interpretation
is indicated by the 'mplsFecType' object.
In other words, the FEC element is populated
according to the Prefix FEC Element value encoding, or
the Host Address FEC Element encoding."
REFERENCE
"RFC3036, Section 3.4.1 FEC TLV."
::= { mplsFecEntry 5 }
mplsFecAddrPrefixLength OBJECT-TYPE
SYNTAX InetAddressPrefixLength
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"If the value of the 'mplsFecType' is 'hostAddress(2)'
then this object is undefined.
If the value of 'mplsFecType' is 'prefix(1)'
then the value of this object is the length in
bits of the address prefix represented by
'mplsFecAddr', or zero. If the value of this
object is zero, this indicates that the
prefix matches all addresses. In this case the
address prefix MUST also be zero (i.e., 'mplsFecAddr'
should have the value of zero.)"
REFERENCE
"RFC3036, Section 3.4.1. FEC TLV."
DEFVAL { 0 }
::= { mplsFecEntry 3 }
mplsFecStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this conceptual row.
Conceptual rows having the value 'permanent(4)'
need not allow write-access to any columnar
objects in the row."
DEFVAL { nonVolatile }
::= { mplsFecEntry 6 }
mplsFecRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. If the value of this
object is 'active(1)', then none of the writable objects
of this entry can be modified, except to set this object
to 'destroy(6)'.
NOTE: if this row is being referenced by any entry in
the mplsLdpLspFecTable, then a request to destroy
this row, will result in an inconsistentValue error."
::= { mplsFecEntry 7 }
--
-- LDP LSP FEC Table
--
mplsLdpLspFecLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime at the time of the most
recent addition/deletion of an entry
to/from the mplsLdpLspFecTable or
the most recent change in values to any objects in the
mplsLdpLspFecTable.
If no such changes have occurred since the last
re-initialization of the local management subsystem,
then this object contains a zero value."
::= { mplsLdpSessionObjects 9 }
mplsLdpLspFecTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpLspFecEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table which shows the relationship between
LDP LSPs and FECs. Each row represents
a single LDP LSP to FEC association."
::= { mplsLdpSessionObjects 10 }
mplsLdpLspFecEntry OBJECT-TYPE
SYNTAX MplsLdpLspFecEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry represents a LDP LSP
to FEC association."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpPeerLdpId,
mplsLdpLspFecSegment,
mplsLdpLspFecSegmentIndex,
mplsLdpLspFecIndex
}
::= { mplsLdpLspFecTable 1 }
MplsLdpLspFecEntry ::= SEQUENCE {
mplsLdpLspFecSegment INTEGER,
mplsLdpLspFecSegmentIndex MplsIndexType,
mplsLdpLspFecIndex IndexInteger,
mplsLdpLspFecStorageType StorageType,
mplsLdpLspFecRowStatus RowStatus
}
mplsLdpLspFecSegment OBJECT-TYPE
SYNTAX INTEGER {
inSegment(1),
outSegment(2)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"If the value is inSegment(1), then this
indicates that the following index,
mplsLdpLspFecSegmentIndex, contains the same
value as the mplsInSegmentLdpLspIndex.
Otherwise, if the value of this object is
outSegment(2), then this
indicates that following index,
mplsLdpLspFecSegmentIndex, contains the same
value as the mplsOutSegmentLdpLspIndex."
::= { mplsLdpLspFecEntry 1 }
mplsLdpLspFecSegmentIndex OBJECT-TYPE
SYNTAX MplsIndexType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This index is interpretted by using the value
of the mplsLdpLspFecSegment.
If the mplsLdpLspFecSegment is inSegment(1),
then this index has the same value as
mplsInSegmentLdpLspIndex.
If the mplsLdpLspFecSegment is outSegment(2),
then this index has the same value as
mplsOutSegmentLdpLspIndex."
::= { mplsLdpLspFecEntry 2 }
mplsLdpLspFecIndex OBJECT-TYPE
SYNTAX IndexInteger
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This index identifies the FEC entry in the
mplsFecTable associated with this session.
In other words, the value of this index
is the same as the value of the mplsFecIndex
that denotes the FEC associated with this
Session."
::= { mplsLdpLspFecEntry 3 }
mplsLdpLspFecStorageType OBJECT-TYPE
SYNTAX StorageType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The storage type for this conceptual row.
Conceptual rows having the value 'permanent(4)'
need not allow write-access to any columnar
objects in the row."
DEFVAL { nonVolatile }
::= { mplsLdpLspFecEntry 4 }
mplsLdpLspFecRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this conceptual row. If the
value of this object is 'active(1)', then
none of the writable objects of this entry
can be modified.
The Agent should delete this row when
the session ceases to exist. If an
operator wants to associate the session with
a different FEC, the recommended
procedure is (as described in detail in the section
entitled, 'Changing Values After Session
Establishment', and again described in the
DESCRIPTION clause of the
mplsLdpEntityAdminStatus object)
is to set the mplsLdpEntityAdminStatus to
down, thereby explicitly causing a session
to be torn down. This will also
cause this entry to be deleted.
Then, set the mplsLdpEntityAdminStatus
to enable which enables a new session to be initiated.
Once the session is initiated, an entry may be
added to this table to associate the new session
with a FEC."
::= { mplsLdpLspFecEntry 5 }
--
-- Address Message/Address Withdraw Message Information
--
-- This information is associated with a specific Session
-- because Label Address Messages are sent after session
-- initialization has taken place.
--
mplsLdpSessionPeerAddrTable OBJECT-TYPE
SYNTAX SEQUENCE OF MplsLdpSessionPeerAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table 'extends' the mplsLdpSessionTable.
This table is used to store Label Address Information
from Label Address Messages received by this LSR from
Peers. This table is read-only and should be updated
when Label Withdraw Address Messages are received, i.e.,
Rows should be deleted as appropriate.
NOTE: since more than one address may be contained
in a Label Address Message, this table 'sparse augments',
the mplsLdpSessionTable's information."
::= { mplsLdpSessionObjects 11 }
mplsLdpSessionPeerAddrEntry OBJECT-TYPE
SYNTAX MplsLdpSessionPeerAddrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table represents information on
a session's single next hop address which was
advertised in an Address Message from the LDP peer.
The information contained in a row is read-only."
INDEX { mplsLdpEntityLdpId,
mplsLdpEntityIndex,
mplsLdpPeerLdpId,
mplsLdpSessionPeerAddrIndex
}
::= { mplsLdpSessionPeerAddrTable 1 }
MplsLdpSessionPeerAddrEntry ::= SEQUENCE {
mplsLdpSessionPeerAddrIndex Unsigned32,
mplsLdpSessionPeerNextHopAddrType InetAddressType,
mplsLdpSessionPeerNextHopAddr InetAddress
}
mplsLdpSessionPeerAddrIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An index which uniquely identifies this entry within
a given session."
::= { mplsLdpSessionPeerAddrEntry 1 }
mplsLdpSessionPeerNextHopAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The internetwork layer address type of this Next Hop
Address as specified in the Label Address Message
associated with this Session. The value of this
object indicates how to interpret the value of
mplsLdpSessionPeerNextHopAddr."
::= { mplsLdpSessionPeerAddrEntry 2 }
mplsLdpSessionPeerNextHopAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The next hop address. The type of this address
is specified by the value of the
mplsLdpSessionPeerNextHopAddrType."
REFERENCE
"RFC3036, Section 2.7. LDP Identifiers
and Next Hop Addresses"
::= { mplsLdpSessionPeerAddrEntry 3 }
---
--- Notifications
---
mplsLdpInitSessionThresholdExceeded NOTIFICATION-TYPE
OBJECTS {
mplsLdpEntityInitSessionThreshold
}
STATUS current
DESCRIPTION
"This notification is generated when the value of
the 'mplsLdpEntityInitSessionThreshold' object
is not zero, and the number of Session
Initialization messages exceeds the value
of the 'mplsLdpEntityInitSessionThreshold' object."
::= { mplsLdpNotifications 1 }
mplsLdpPathVectorLimitMismatch NOTIFICATION-TYPE
OBJECTS {
mplsLdpEntityPathVectorLimit,
mplsLdpPeerPathVectorLimit
}
STATUS current
DESCRIPTION
"This notification is sent when the
'mplsLdpEntityPathVectorLimit' does NOT match
the value of the 'mplsLdpPeerPathVectorLimit' for
a specific Entity."
REFERENCE
"RFC3036, LDP Specification, Section 3.5.3."
::= { mplsLdpNotifications 2 }
mplsLdpSessionUp NOTIFICATION-TYPE
OBJECTS {
mplsLdpSessionState,
mplsLdpSessionDiscontinuityTime,
mplsLdpSessionStatsUnknownMesTypeErrors,
mplsLdpSessionStatsUnknownTlvErrors
}
STATUS current
DESCRIPTION
"If this notification is sent when the
value of 'mplsLdpSessionState' enters
the 'operational(5)' state."
::= { mplsLdpNotifications 3 }
mplsLdpSessionDown NOTIFICATION-TYPE
OBJECTS {
mplsLdpSessionState,
mplsLdpSessionDiscontinuityTime,
mplsLdpSessionStatsUnknownMesTypeErrors,
mplsLdpSessionStatsUnknownTlvErrors
}
STATUS current
DESCRIPTION
"This notification is sent when the
value of 'mplsLdpSessionState' leaves
the 'operational(5)' state."
::= { mplsLdpNotifications 4 }
--****************************************************************
-- Module Conformance Statement
--****************************************************************
mplsLdpGroups
OBJECT IDENTIFIER ::= { mplsLdpConformance 1 }
mplsLdpCompliances
OBJECT IDENTIFIER ::= { mplsLdpConformance 2 }
--
-- Full Compliance
--
mplsLdpModuleFullCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The Module is implemented with support
for read-create and read-write. In other
words, both monitoring and configuration
are available when using this MODULE-COMPLIANCE."
MODULE -- this module
MANDATORY-GROUPS { mplsLdpGeneralGroup,
mplsLdpNotificationsGroup
}
GROUP mplsLdpLspGroup
DESCRIPTION
"This group must be supported if the LSR MIB is
implemented, specifically the mplsInSegmentTable,
the mplsOutSegmentTable or the mplsXCTable."
OBJECT mplsLdpEntityTargetPeerAddrType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation is only required to support
'unknown(0)', IPv4 and globally unique IPv6 addresses."
OBJECT mplsLdpEntityTargetPeerAddr
SYNTAX InetAddress (SIZE(0|4|16))
DESCRIPTION
"An implementation is only required to support IPv4 and
globally unique IPv6 addresses."
OBJECT mplsLdpEntityRowStatus
SYNTAX RowStatus { active(1) }
WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }
DESCRIPTION
"Support for createAndWait and notInService is not
required."
OBJECT mplsFecAddrType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation is only required to support
'unknown(0)', IPv4 and globally unique IPv6 addresses."
OBJECT mplsFecAddr
SYNTAX InetAddress (SIZE(0|4|16))
DESCRIPTION
"An implementation is only required to support IPv4 and
globally unique IPv6 addresses."
OBJECT mplsFecRowStatus
SYNTAX RowStatus { active(1) }
WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }
DESCRIPTION
"Support for createAndWait and notInService is not
required."
OBJECT mplsLdpLspFecRowStatus
SYNTAX RowStatus { active(1) }
WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }
DESCRIPTION
"Support for createAndWait and notInService is not
required."
OBJECT mplsLdpSessionPeerNextHopAddrType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation is only required to support
'unknown(0)', IPv4 and globally unique IPv6 addresses."
OBJECT mplsLdpSessionPeerNextHopAddr
SYNTAX InetAddress (SIZE(0|4|16))
DESCRIPTION
"An implementation is only required to support IPv4
and globally unique IPv6 addresses."
::= { mplsLdpCompliances 1 }
--
-- Read-Only Compliance
--
mplsLdpModuleReadOnlyCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The Module is implemented with support
for read-only. In other words, only monitoring
is available by implementing this MODULE-COMPLIANCE."
MODULE -- this module
MANDATORY-GROUPS { mplsLdpGeneralGroup,
mplsLdpNotificationsGroup
}
GROUP mplsLdpLspGroup
DESCRIPTION
"This group must be supported if the LSR MIB is
implemented, specifically the mplsInSegmentTable,
the mplsOutSegmentTable or the mplsXCTable."
OBJECT mplsLdpEntityProtocolVersion
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsLdpEntityAdminStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsLdpEntityTcpPort
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsLdpEntityUdpDscPort
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsLdpEntityMaxPduLength
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsLdpEntityKeepAliveHoldTimer
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsLdpEntityHelloHoldTimer
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsLdpEntityInitSessionThreshold
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsLdpEntityLabelDistMethod
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsLdpEntityLabelRetentionMode
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsLdpEntityPathVectorLimit
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsLdpEntityHopCountLimit
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsLdpEntityTransportAddrKind
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsLdpEntityTargetPeer
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsLdpEntityTargetPeerAddrType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required.
An implementation is only required to support
'unknown(0)', IPv4 and globally unique IPv6 addresses."
OBJECT mplsLdpEntityTargetPeerAddr
SYNTAX InetAddress (SIZE(0|4|16))
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required.
An implementation is only required to support IPv4 and
globally unique IPv6 addresses."
OBJECT mplsLdpEntityLabelType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsLdpEntityStorageType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsLdpEntityRowStatus
SYNTAX RowStatus { active(1) }
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required, and active is the
only status that needs to be supported."
OBJECT mplsFecType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsFecAddrPrefixLength
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsFecAddrType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required.
An implementation is only required to support
'unknown(0)', IPv4 and globally unique IPv6 addresses."
OBJECT mplsFecAddr
SYNTAX InetAddress (SIZE(0|4|16))
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required.
An implementation is only required to support IPv4 and
globally unique IPv6 addresses."
OBJECT mplsFecStorageType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsFecRowStatus
SYNTAX RowStatus { active(1) }
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required, and active is the
only status that needs to be supported."
OBJECT mplsLdpLspFecStorageType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT mplsLdpLspFecRowStatus
SYNTAX RowStatus { active(1) }
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required, and active is the
only status that needs to be supported."
OBJECT mplsLdpSessionPeerNextHopAddrType
SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) }
DESCRIPTION
"An implementation is only required to support
'unknown(0)', IPv4 and globally unique IPv6 addresses."
OBJECT mplsLdpSessionPeerNextHopAddr
SYNTAX InetAddress (SIZE(0|4|16))
DESCRIPTION
"An implementation is only required to support IPv4
and globally unique IPv6 addresses."
::= { mplsLdpCompliances 2 }
-- units of conformance
mplsLdpGeneralGroup OBJECT-GROUP
OBJECTS {
mplsLdpLsrId,
mplsLdpLsrLoopDetectionCapable,
mplsLdpEntityLastChange,
mplsLdpEntityIndexNext,
mplsLdpEntityProtocolVersion,
mplsLdpEntityAdminStatus,
mplsLdpEntityOperStatus,
mplsLdpEntityTcpPort,
mplsLdpEntityUdpDscPort,
mplsLdpEntityMaxPduLength,
mplsLdpEntityKeepAliveHoldTimer,
mplsLdpEntityHelloHoldTimer,
mplsLdpEntityInitSessionThreshold,
mplsLdpEntityLabelDistMethod,
mplsLdpEntityLabelRetentionMode,
mplsLdpEntityPathVectorLimit,
mplsLdpEntityHopCountLimit,
mplsLdpEntityTransportAddrKind,
mplsLdpEntityTargetPeer,
mplsLdpEntityTargetPeerAddrType,
mplsLdpEntityTargetPeerAddr,
mplsLdpEntityLabelType,
mplsLdpEntityDiscontinuityTime,
mplsLdpEntityStorageType,
mplsLdpEntityRowStatus,
mplsLdpEntityStatsSessionAttempts,
mplsLdpEntityStatsSessionRejectedNoHelloErrors,
mplsLdpEntityStatsSessionRejectedAdErrors,
mplsLdpEntityStatsSessionRejectedMaxPduErrors,
mplsLdpEntityStatsSessionRejectedLRErrors,
mplsLdpEntityStatsBadLdpIdentifierErrors,
mplsLdpEntityStatsBadPduLengthErrors,
mplsLdpEntityStatsBadMessageLengthErrors,
mplsLdpEntityStatsBadTlvLengthErrors,
mplsLdpEntityStatsMalformedTlvValueErrors,
mplsLdpEntityStatsKeepAliveTimerExpErrors,
mplsLdpEntityStatsShutdownReceivedNotifications,
mplsLdpEntityStatsShutdownSentNotifications,
mplsLdpPeerLastChange,
mplsLdpPeerLabelDistMethod,
mplsLdpPeerPathVectorLimit,
mplsLdpPeerTransportAddrType,
mplsLdpPeerTransportAddr,
mplsLdpHelloAdjacencyHoldTimeRem,
mplsLdpHelloAdjacencyHoldTime,
mplsLdpHelloAdjacencyType,
mplsLdpSessionStateLastChange,
mplsLdpSessionState,
mplsLdpSessionRole,
mplsLdpSessionProtocolVersion,
mplsLdpSessionKeepAliveHoldTimeRem,
mplsLdpSessionKeepAliveTime,
mplsLdpSessionMaxPduLength,
mplsLdpSessionDiscontinuityTime,
mplsLdpSessionStatsUnknownMesTypeErrors,
mplsLdpSessionStatsUnknownTlvErrors,
mplsLdpSessionPeerNextHopAddrType,
mplsLdpSessionPeerNextHopAddr,
mplsFecLastChange,
mplsFecIndexNext,
mplsFecType,
mplsFecAddrType,
mplsFecAddr,
mplsFecAddrPrefixLength,
mplsFecStorageType,
mplsFecRowStatus
}
STATUS current
DESCRIPTION
"Objects that apply to all MPLS LDP implementations."
::= { mplsLdpGroups 1 }
mplsLdpLspGroup OBJECT-GROUP
OBJECTS {
mplsInSegmentLdpLspLabelType,
mplsInSegmentLdpLspType,
mplsOutSegmentLdpLspLabelType,
mplsOutSegmentLdpLspType,
mplsLdpLspFecLastChange,
mplsLdpLspFecStorageType,
mplsLdpLspFecRowStatus
}
STATUS current
DESCRIPTION
"These objects are for LDP implementations
which interface to the Label Information Base (LIB)
in the MPLS-LSR-STD-MIB. The LIB is
represented in the mplsInSegmentTable,
mplsOutSegmentTable and mplsXCTable."
::= { mplsLdpGroups 2 }
mplsLdpNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS { mplsLdpInitSessionThresholdExceeded,
mplsLdpPathVectorLimitMismatch,
mplsLdpSessionUp,
mplsLdpSessionDown
}
STATUS current
DESCRIPTION
"The notification for an MPLS LDP implementation."
::= { mplsLdpGroups 3 }
END