melissaml fa999b8135 Replace Chinese quotes to English quotes

Change-Id: I3a9351095355219080f685e427f195bb9190dcd9

2018-02-15 11:43:51 +08:00

21 KiB

Raw Blame History

Hitachi NAS Platform File Services Driver for OpenStack

Driver Version 3.0

Hitachi NAS Platform Storage Requirements

This Hitachi NAS Platform File Services Driver for OpenStack provides support for Hitachi NAS Platform (HNAS) models 3080, 3090, 4040, 4060, 4080 and 4100 with NAS OS 12.2 or higher. Before configuring the driver, ensure the HNAS has at least:

1 storage pool (span) configured.
1 EVS configured.
1 file system in this EVS, created without replication target option and should be in mounted state. It is recommended to disable auto-expansion, because the scheduler uses the current free space reported by the file system when creating shares.
1 Management User configured with "supervisor" permission level.
Hitachi NAS Management interface should be reachable from manila-share node.

Also, if the driver is going to create CIFS shares, either LDAP servers or domains must be configured previously in HNAS to provide the users and groups.

Supported Operations

The following operations are supported in this version of Hitachi NAS Platform File Services Driver for OpenStack:

Create and delete CIFS and NFS shares;
Extend and shrink shares;
Manage rules to shares (allow/deny access);
Allow and deny share access;
- IP access type supported for NFS shares;
- User access type supported for CIFS shares;
- Both RW and RO access level are supported for NFS and CIFS shares;
Manage and unmanage shares;
Create and delete snapshots;
Create shares from snapshots.

Driver Configuration

This document contains the installation and user guide of the Hitachi NAS Platform File Services Driver for OpenStack. Although mentioning some Shared File Systems service operations and HNAS commands, both are not in the scope of this document. Please refer to their own guides for details.

Before configuring the driver, make sure that the nodes running the manila-share service have access to the HNAS management port, and compute and network nodes have access to the data ports (EVS IPs or aggregations).

The driver configuration can be summarized in the following steps:

Configure HNAS parameters on manila.conf;
Prepare the network ensuring all OpenStack-HNAS connections mentioned above;
Configure/create share type;
Restart the services;
Configure OpenStack networks.

Step 1 - HNAS Parameters Configuration

The following parameters need to be configured in the [DEFAULT] section of /etc/manila/manila.conf:

Option	Description
enabled_share_backends	Name of the section on `manila.conf` used to specify a backend. For example: enabled_share_backends = hnas1
enabled_share_protocols	Specify a list of protocols to be allowed for share creation. This driver version supports NFS and/or CIFS.

The following parameters need to be configured in the [backend] section of /etc/manila/manila.conf:

Option	Description
share_backend_name	A name for the backend.
share_driver	Python module path. For this driver this must be: manila.share.drivers.hitachi.hnas.driver.HitachiHNASDriver
driver_handles_share_servers	Driver working mode. For this driver this must be: False.
hitachi_hnas_ip	HNAS management interface IP for communication between manila-share node and HNAS.
hitachi_hnas_user	This field is used to provide user credential to HNAS. Provided management user must have "supervisor" level.
hitachi_hnas_password	This field is used to provide password credential to HNAS. Either hitachi_hnas_password or hitachi_hnas_ssh_private_key must be set.
hitachi_hnas_ssh_private_key	Set this parameter with RSA/DSA private key path to allow the driver to connect into HNAS.
hitachi_hnas_evs_id	ID from EVS which this backend is assigned to (ID can be listed by CLI "evs list" or EVS Management in HNAS Interface).
hitachi_hnas_evs_ip	EVS IP for mounting shares (this can be listed by CLI "evs list" or EVS Management in HNAS interface).
hitachi_hnas_file_system_name	Name of the file system in HNAS, located in the specified EVS.
hitachi_hnas_cluster_admin_ip0*	If HNAS is in a multi-farm (one SMU managing multiple HNAS) configuration, set this parameter with the IP of the cluster's admin node.
hitachi_hnas_stalled_job_timeout*	Tree-clone-job commands are used to create snapshots and create shares from snapshots. This parameter sets a timeout (in seconds) to wait for jobs to complete. Default value is 30 seconds.
hitachi_hnas_driver_helper*	Python module path for the driver helper. For this driver, it should use (default value): manila.share.drivers.hitachi.hnas.ssh.HNASSSHBackend
hitachi_hnas_allow_cifs_snapshot_while_mounted*	By default, CIFS snapshots are not allowed to be taken while the share has clients connected because point-in-time replica cannot be guaranteed for all files. This parameter can be set to True to allow snapshots to be taken while the share has clients connected. WARNING: Setting this parameter to True might cause inconsistent snapshots on CIFS shares. Default value is False.

* Non mandatory parameters.

Below is an example of a valid configuration of HNAS driver:

[DEFAULT]``
...
enabled_share_backends = hitachi1
enabled_share_protocols = CIFS,NFS
...

[hitachi1]
share_backend_name = HITACHI1
share_driver = manila.share.drivers.hitachi.hnas.driver.HitachiHNASDriver
driver_handles_share_servers = False
hitachi_hnas_ip = 172.24.44.15
hitachi_hnas_user = supervisor
hitachi_hnas_password = supervisor
hitachi_hnas_evs_id = 1
hitachi_hnas_evs_ip = 10.0.1.20
hitachi_hnas_file_system_name = FS-Manila

Step 2 - Prepare the Network

In the driver mode used by Hitachi NAS Platform File Services Driver for OpenStack, driver_handles_share_servers (DHSS) as False, the driver does not handle network configuration, it is up to the administrator to configure it. It is mandatory that HNAS management interface is reachable from a manila-share node through admin network, while the selected EVS data interface is reachable from OpenStack Cloud, such as through neutron flat networking. Here is a step-by-step of an example configuration:

Manila-Share Node:
eth0: Admin Network, can ping HNAS management interface.
eth1: Data Network, can ping HNAS EVS IP (data interface). This interface is only required if you plan to use Share Migration.

Network Node and Compute Nodes:
eth0: Admin Network, can ping HNAS management interface.
eth1: Data Network, can ping HNAS EVS IP (data interface).

The following image represents the described scenario:

Run in Network Node:

$ sudo ifconfig eth1 0
$ sudo ovs-vsctl add-br br-eth1
$ sudo ovs-vsctl add-port br-eth1 eth1
$ sudo ifconfig eth1 up

Edit /etc/neutron/plugins/ml2/ml2_conf.ini (default directory), change the following settings as follows in their respective tags:

[ml2]
type_drivers = flat,vlan,vxlan,gre
mechanism_drivers = openvswitch

[ml2_type_flat]
flat_networks = physnet1,physnet2

[ml2_type_vlan]
network_vlan_ranges = physnet1:1000:1500,physnet2:2000:2500

[ovs]
bridge_mappings = physnet1:br-ex,physnet2:br-eth1

You may have to repeat the last line above in another file in the Compute Node, if it exists is located in: /etc/neutron/plugins/openvswitch/ovs_neutron_plugin.ini.

Create a route in HNAS to the tenant network. Please make sure multi-tenancy is enabled and routes are configured per EVS. Use the command "route-net-add" in HNAS console, where the network parameter should be the tenant's private network, while the gateway parameter should be the flat network gateway and the "console-context --evs" parameter should be the ID of EVS in use, such as in the following example:

$ console-context --evs 3 route-net-add --gateway 192.168.1.1 10.0.0.0/24

Shared File Systems service requires that the share type includes the driver_handles_share_servers extra-spec. This ensures that the share will be created on a backend that supports the requested driver_handles_share_servers capability. For the Hitachi NAS Platform File Services Driver for OpenStack this must be set to False.

$ manila type-create hitachi False

Additionally, the driver also reports the following common capabilities that can be specified in the share type:

Capability	Description
thin_provisioning = True	All shares created on HNAS are always thin provisioned. So, if you set it, the value must be: True.
dedupe = True/False	HNAS supports deduplication on its file systems and the driver will report dedupe=True if it is enabled on the file system being used. To use it, go to HNAS and enable the feature on the file system used.

To specify a common capability on the share type, use the type-key command, for example:

$ manila type-key hitachi set dedupe=True

Step 4 - Restart the Services

Restart all Shared File Systems services (manila-share, manila-scheduler and manila-api) and neutron services (neutron-*). This step is specific to your environment. If you are running in devstack for example, you have to log into screen (screen -r), stop the process (Ctrl^C) and run it again. If you are running it in a distro like RHEL or SUSE, a service command (for example service manila-api restart) is used to restart the service.

Step 5 - Configure OpenStack Networks

In Neutron Controller it is necessary to create a network, a subnet and to add this subnet interface to a router:

Create a network to the given tenant (demo), providing the DEMO_ID (this can be fetched using keystone tenant-list), a name for the network, the name of the physical network over which the virtual network is implemented and the type of the physical mechanism by which the virtual network is implemented:

$ neutron net-create --tenant-id <DEMO_ID> hnas_network
--provider:physical_network=physnet2 --provider:network_type=flat

Create a subnet to same tenant (demo), providing the DEMO_ID (this can be fetched using keystone tenant-list), the gateway IP of this subnet, a name for the subnet, the network ID created on previously step (this can be fetched using neutron net-list) and CIDR of subnet:

$ neutron subnet-create --tenant-id <DEMO_ID> --gateway <GATEWAY>
--name hnas_subnet <NETWORK_ID> <SUBNET_CIDR>

Finally, add the subnet interface to a router, providing the router ID and subnet ID created on previously step (can be fetched using neutron subnet-list):

$ neutron router-interface-add <ROUTER_ID> <SUBNET_ID>

Manage and Unmanage Shares

Manila has the ability to manage and unmanage shares. If there is a share in the storage and it is not in OpenStack, you can manage that share and use it as a manila share. Hitachi NAS Platform File Services Driver for OpenStack use virtual-volumes (V-VOLs) to create shares. Only V-VOLs with a quota limit can be used by the driver, also, they must be created or moved inside the directory '/shares/' and exported (as NFS or CIFS shares). The unmanage operation only unlinks the share from OpenStack, preserving all data in the share.

To manage shares use:

$ manila manage [--name <name>] [--description <description>]
[--share_type <share_type>] [--driver_options [<key=value> [<key=value> ...]]]
<service_host> <protocol> <export_path>

Where:

Parameter	Description
service_host	Manila host, backend and share name. For example ubuntu@hitachi1#HITACHI1. The available hosts can be listed with the command: manila pool-list (admin only).
protocol	NFS or CIFS protocols are currently supported.
export_path	The export path of the share. For example: 172.24.44.31:/shares/some_share_id

To unmanage a share use:

$ manila unmanage <share_id>