openstack-manuals/doc/install-guide-debconf/source/nova-compute-install.rst

Install and configure a compute node

This section describes how to install and configure the Compute service on a compute node. The service supports several hypervisors <hypervisor> to deploy instances <instance> or VMs <virtual machine (VM)>. For simplicity, this configuration uses the QEMU <Quick EMUlator (QEMU)> hypervisor with the KVM <kernel-based VM (KVM)> extension on compute nodes that support hardware acceleration for virtual machines. On legacy hardware, this configuration uses the generic QEMU hypervisor. You can follow these instructions with minor modifications to horizontally scale your environment with additional compute nodes.

Note

This section assumes that you are following the instructions in this guide step-by-step to configure the first compute node. If you want to configure additional compute nodes, prepare them in a similar fashion to the first compute node in the example architectures <overview-example-architectures> section. Each additional compute node requires a unique IP address.

Install and configure components

1. Install the packages:

   # apt-get install nova-compute

   Respond to prompts for database management <debconf/debconf-dbconfig-common>, Identity service credentials <debconf/debconf-keystone-authtoken>, and message broker credentials <debconf/debconf-rabbitmq>. Make sure that you do not activate database management handling by debconf, as a compute node should not access the central database.

2. Edit the /etc/nova/nova.conf file and complete the following actions:

   • In the [DEFAULT] section, check that the my_ip option is correctly set (this value is handled by the config and postinst scripts of the nova-common package using debconf):

     [DEFAULT]
     ...
     my_ip = MANAGEMENT_INTERFACE_IP_ADDRESS

     Replace MANAGEMENT_INTERFACE_IP_ADDRESS with the IP address of the management network interface on your compute node, typically 10.0.0.31 for the first node in the example architecture <overview-example-architectures>.

   • In the [DEFAULT] section, enable support for the Networking service:

     [DEFAULT]
     ...
     use_neutron = True
     firewall_driver = nova.virt.firewall.NoopFirewallDriver

     Note

     By default, Compute uses an internal firewall service. Since Networking includes a firewall service, you must disable the Compute firewall service by using the nova.virt.firewall.NoopFirewallDriver firewall driver.

   • In the [vnc] section, enable and configure remote console access:

     [vnc]
     ...
     enabled = True
     vncserver_listen = 0.0.0.0
     vncserver_proxyclient_address = $my_ip
     novncproxy_base_url = http://controller:6080/vnc_auto.html

     The server component listens on all IP addresses and the proxy component only listens on the management interface IP address of the compute node. The base URL indicates the location where you can use a web browser to access remote consoles of instances on this compute node.

     Note

     If the web browser to access remote consoles resides on a host that cannot resolve the controller hostname, you must replace controller with the management interface IP address of the controller node.

   • In the [glance] section, configure the location of the Image service API:

     [glance]
     ...
     api_servers = http://controller:9292

3. Ensure the kernel module nbd is loaded.

   # modprobe nbd

4. Ensure the module loads on every boot by adding nbd to the /etc/modules-load.d/nbd.conf file.

Finalize installation

1. Determine whether your compute node supports hardware acceleration for virtual machines:

   $ egrep -c '(vmx|svm)' /proc/cpuinfo

   If this command returns a value of one or greater, your compute node supports hardware acceleration which typically requires no additional configuration.

   If this command returns a value of zero, your compute node does not support hardware acceleration and you must configure libvirt to use QEMU instead of KVM.

   • Replace the nova-compute-kvm package with nova-compute-qemu which automatically changes the /etc/nova/nova-compute.conf file and installs the necessary dependencies:

     # apt-get install nova-compute-qemu

2. Restart the Compute service:

   # service nova-compute restart