13 KiB
Network Design
OpenStack provides a rich networking environment, and this chapter details the requirements and options to deliberate when designing your cloud.
Warning
If this is the first time you are deploying a cloud infrastructure in your organization, after reading this section, your first conversations should be with your networking team. Network usage in a running cloud is vastly different from traditional network deployments and has the potential to be disruptive at both a connectivity and a policy level.
For example, you must plan the number of IP addresses that you need for both your guest instances as well as management infrastructure. Additionally, you must research and discuss cloud network connectivity through proxy servers and firewalls.
In this chapter, we'll give some examples of network implementations to consider and provide information about some of the network layouts that OpenStack uses. Finally, we have some brief notes on the networking services that are essential for stable operation.
Management Network
A management network (a separate network for use by
your cloud operators) typically consists of a separate switch and
separate NICs (network interface cards), and is a recommended option.
This segregation prevents system administration and the monitoring of
system access from being disrupted by traffic generated by guests.
Consider creating other private networks for communication between internal components of OpenStack, such as the message queue and OpenStack Compute. Using a virtual local area network (VLAN) works well for these scenarios because it provides a method for creating multiple virtual networks on a physical network.
Public Addressing Options
There are two main types of IP addresses for guest virtual machines: fixed IPs and floating IPs. Fixed IPs are assigned to instances on boot, whereas floating IP addresses can change their association between instances by action of the user. Both types of IP addresses can be either public or private, depending on your use case.
Fixed IP addresses are required, whereas it is possible to run OpenStack without floating IPs. One of the most common use cases for floating IPs is to provide public IP addresses to a private cloud, where there are a limited number of IP addresses available. Another is for a public cloud user to have a "static" IP address that can be reassigned when an instance is upgraded or moved.
Fixed IP addresses can be private for private clouds, or public for public clouds. When an instance terminates, its fixed IP is lost. It is worth noting that newer users of cloud computing may find their ephemeral nature frustrating.
IP Address Planning
An OpenStack installation can potentially have many subnets (ranges of IP addresses) and different types of services in each. An IP address plan can assist with a shared understanding of network partition purposes and scalability. Control services can have public and private IP addresses, and as noted above, there are a couple of options for an instance's public addresses.
An IP address plan might be broken down into the following sections:
- Subnet router
-
Packets leaving the subnet go via this address, which could be a dedicated router or a
nova-networkservice. - Control services public interfaces
-
Public access to
swift-proxy,nova-api,glance-api, and horizon come to these addresses, which could be on one side of a load balancer or pointing at individual machines. - Object Storage cluster internal communications
-
Traffic among object/account/container servers and between these and the proxy server's internal interface uses this private network.
- Compute and storage communications
-
If ephemeral or block storage is external to the compute node, this network is used.
- Out-of-band remote management
-
If a dedicated remote access controller chip is included in servers, often these are on a separate network.
- In-band remote management
-
Often, an extra (such as 1 GB) interface on compute or storage nodes is used for system administrators or monitoring tools to access the host instead of going through the public interface.
- Spare space for future growth
-
Adding more public-facing control services or guest instance IPs should always be part of your plan.
For example, take a deployment that has both OpenStack Compute and Object Storage, with private ranges 172.22.42.0/24 and 172.22.87.0/26 available. One way to segregate the space might be as follows:
172.22.42.0/24:
172.22.42.1 - 172.22.42.3 - subnet routers
172.22.42.4 - 172.22.42.20 - spare for networks
172.22.42.21 - 172.22.42.104 - Compute node remote access controllers
(inc spare)
172.22.42.105 - 172.22.42.188 - Compute node management interfaces (inc spare)
172.22.42.189 - 172.22.42.208 - Swift proxy remote access controllers
(inc spare)
172.22.42.209 - 172.22.42.228 - Swift proxy management interfaces (inc spare)
172.22.42.229 - 172.22.42.252 - Swift storage servers remote access controllers
(inc spare)
172.22.42.253 - 172.22.42.254 - spare
172.22.87.0/26:
172.22.87.1 - 172.22.87.3 - subnet routers
172.22.87.4 - 172.22.87.24 - Swift proxy server internal interfaces
(inc spare)
172.22.87.25 - 172.22.87.63 - Swift object server internal interfaces
(inc spare)A similar approach can be taken with public IP addresses, taking note
that large, flat ranges are preferred for use with guest instance IPs.
Take into account that for some OpenStack networking options, a public
IP address in the range of a guest instance public IP address is
assigned to the nova-compute host.
Network Topology
OpenStack Compute with nova-network provides predefined
network deployment models, each with its own strengths and weaknesses.
The selection of a network manager changes your network topology, so the
choice should be made carefully. You also have a choice between the
tried-and-true legacy nova-network settings or the neutron
project for OpenStack Networking. Both offer networking for launched
instances with different implementations and requirements.
For OpenStack Networking with the neutron project, typical
configurations are documented with the idea that any setup you can
configure with real hardware you can re-create with a software-defined
equivalent. Each tenant can contain typical network elements such as
routers, and services such as DHCP <Dynamic Host Configuration
Protocol (DHCP)>.
table_networking_deployment describes the networking
deployment options for both legacy nova-network options and
an equivalent neutron configuration.
| Network deployment model | Strengths | Weaknesses | Neutron equivalent |
|---|---|---|---|
| Flat | Extremely simple topology. No DHCP overhead. | Requires file injection into the instance to configure network interfaces. | Configure a single bridge as the integration bridge (br-int) and connect it to a physical network interface with the Modular Layer 2 (ML2) plug-in, which uses Open vSwitch by default. |
| FlatDHCP | Relatively simple to deploy. Standard networking. Works with all guest operating systems. | Requires its own DHCP broadcast domain. | Configure DHCP agents and routing agents. Network Address Translation (NAT) performed outside of compute nodes, typically on one or more network nodes. |
| VlanManager | Each tenant is isolated to its own VLANs. | More complex to set up. Requires its own DHCP broadcast domain. Requires many VLANs to be trunked onto a single port. Standard VLAN number limitation. Switches must support 802.1q VLAN tagging. | Isolated tenant networks implement some form of isolation of layer 2 traffic between distinct networks. VLAN tagging is key concept, where traffic is “tagged” with an ordinal identifier for the VLAN. Isolated network implementations may or may not include additional services like DHCP, NAT, and routing. |
| FlatDHCP Multi-host with high availability (HA) | Networking failure is isolated to the VMs running on the affected hypervisor. DHCP traffic can be isolated within an individual host. Network traffic is distributed to the compute nodes. | More complex to set up. Compute nodes typically need IP addresses accessible by external networks. Options must be carefully configured for live migration to work with networking services. | Configure neutron with multiple DHCP and layer-3 agents. Network nodes are not able to failover to each other, so the controller runs networking services, such as DHCP. Compute nodes run the ML2 plug-in with support for agents such as Open vSwitch or Linux Bridge. |
Both nova-network and neutron services provide similar
capabilities, such as VLAN between VMs. You also can provide multiple
NICs on VMs with either service. Further discussion follows.
VLAN Configuration Within OpenStack VMs
VLAN configuration can be as simple or as complicated as desired. The use of VLANs has the benefit of allowing each project its own subnet and broadcast segregation from other projects. To allow OpenStack to efficiently use VLANs, you must allocate a VLAN range (one for each project) and turn each compute node switch port into a trunk port.
For example, if you estimate that your cloud must support a maximum of 100 projects, pick a free VLAN range that your network infrastructure is currently not using (such as VLAN 200–299). You must configure OpenStack with this range and also configure your switch ports to allow VLAN traffic from that range.
Multi-NIC Provisioning
OpenStack Networking with neutron and OpenStack Compute
with nova-network have the ability to assign multiple NICs
to instances. For nova-network this can be done on a
per-request basis, with each additional NIC using up an entire subnet or
VLAN, reducing the total number of supported projects.
Multi-Host and Single-Host Networking
The nova-network service has the ability to operate in a
multi-host or single-host mode. Multi-host is when each compute node
runs a copy of nova-network and the instances on that
compute node use the compute node as a gateway to the Internet. The
compute nodes also host the floating IPs and security groups for
instances on that node. Single-host is when a central server—for
example, the cloud controller—runs the nova-network
service. All compute nodes forward traffic from the instances to the
cloud controller. The cloud controller then forwards traffic to the
Internet. The cloud controller hosts the floating IPs and security
groups for all instances on all compute nodes in the cloud.
There are benefits to both modes. Single-node has the downside of a single point of failure. If the cloud controller is not available, instances cannot communicate on the network. This is not true with multi-host, but multi-host requires that each compute node has a public IP address to communicate on the Internet. If you are not able to obtain a significant block of public IP addresses, multi-host might not be an option.
Services for Networking
OpenStack, like any network application, has a number of standard considerations to apply, such as NTP and DNS.
NTP
Time synchronization is a critical element to ensure continued operation of OpenStack components. Correct time is necessary to avoid errors in instance scheduling, replication of objects in the object store, and even matching log timestamps for debugging.
All servers running OpenStack components should be able to access an appropriate NTP server. You may decide to set up one locally or use the public pools available from the Network Time Protocol project.
DNS
OpenStack does not currently provide DNS services, aside from the
dnsmasq daemon, which resides on nova-network hosts. You
could consider providing a dynamic DNS service to allow instances to
update a DNS entry with new IP addresses. You can also consider making a
generic forward and reverse DNS mapping for instances' IP addresses,
such as vm-203-0-113-123.example.com.
Conclusion
Armed with your IP address layout and numbers and knowledge about the topologies and services you can use, it's now time to prepare the network for your installation. Be sure to also check out the OpenStack Security Guide for tips on securing your network. We wish you a good relationship with your networking team!