75618dd786
Change-Id: Ie45dc87e39c1398258e803534c9d45b175658adc Implements: blueprint installguide-liberty
80 lines
2.9 KiB
ReStructuredText
80 lines
2.9 KiB
ReStructuredText
:orphan:
|
|
|
|
======================
|
|
Register API endpoints
|
|
======================
|
|
|
|
All Debian packages for API services, except the ``heat-api`` package,
|
|
register the service in the Identity service catalog. This feature is
|
|
helpful because API endpoints are difficult to remember.
|
|
|
|
.. note::
|
|
|
|
The ``heat-common`` package and not the ``heat-api`` package configures the
|
|
Orchestration service.
|
|
|
|
When you install a package for an API service, you are prompted to
|
|
register that service. However, after you install or upgrade the package
|
|
for an API service, Debian immediately removes your response to this
|
|
prompt from the debconf database. Consequently, you are prompted to
|
|
re-register the service with the Identity service. If you already
|
|
registered the API service, respond ``no`` when you upgrade.
|
|
|
|
.. image:: ../figures/debconf-screenshots/api-endpoint_1_register_endpoint.png
|
|
|
|
|
|
|
|
|
This screen registers packages in the Identity service catalog:
|
|
|
|
.. image:: ../figures/debconf-screenshots/api-endpoint_2_keystone_server_ip.png
|
|
|
|
|
|
|
|
|
You are prompted for the Identity service ``admin_token`` value. The
|
|
Identity Service uses this value to register the API service. When you
|
|
set up the ``keystone`` package, this value is configured automatically.
|
|
|
|
.. image:: ../figures/debconf-screenshots/api-endpoint_3_keystone_authtoken.png
|
|
|
|
|
|
|
|
|
This screen configures the IP addresses for the service. The
|
|
configuration script automatically detects the IP address used by the
|
|
interface that is connected to the default route (``/sbin/route`` and
|
|
``/sbin/ip``).
|
|
|
|
Unless you have a unique set up for your network, press **ENTER**.
|
|
|
|
.. image:: ../figures/debconf-screenshots/api-endpoint_4_service_endpoint_ip_address.png
|
|
|
|
|
|
|
|
|
This screen configures the region name for the service. For example,
|
|
``us-east-coast`` or ``europe-paris``.
|
|
|
|
.. image:: ../figures/debconf-screenshots/api-endpoint_5_region_name.png
|
|
|
|
|
|
|
|
|
The Debian package post installation scripts will then perform the below
|
|
commands for you:
|
|
|
|
.. code-block:: ini
|
|
|
|
PKG_SERVICE_ID=$(pkgos_get_id keystone --os-token ${AUTH_TOKEN} \
|
|
--os-endpoint http://${KEYSTONE_ENDPOINT_IP}:35357/v2.0/ service-create \
|
|
--name ${SERVICE_NAME} --type ${SERVICE_TYPE} --description "${SERVICE_DESC}")
|
|
keystone --os-token ${AUTH_TOKEN} \
|
|
--os-endpoint http://${KEYSTONE_ENDPOINT_IP}:35357/v2.0/
|
|
endpoint-create \
|
|
--region "${REGION_NAME}" --service_id ${PKG_SERVICE_ID} \
|
|
--publicurl http://${PKG_ENDPOINT_IP}:${SERVICE_PORT}${SERVICE_URL} \
|
|
--internalurl http://${PKG_ENDPOINT_IP}:${SERVICE_PORT}${SERVICE_URL} \
|
|
--adminurl http://${PKG_ENDPOINT_IP}:${SERVICE_PORT}${SERVICE_URL})
|
|
|
|
The values of ``AUTH_TOKEN``, ``KEYSTONE_ENDPOINT_IP``,
|
|
``PKG_ENDPOINT_IP``, and ``REGION_NAME`` depend on the answer you will
|
|
provide to the debconf prompts. But the values of ``SERVICE_NAME``,
|
|
``SERVICE_TYPE``, ``SERVICE_DESC``, and ``SERVICE_URL`` are already
|
|
pre-wired in each package, so you don't have to remember them.
|