1166 lines
52 KiB
ReStructuredText
1166 lines
52 KiB
ReStructuredText
=========
|
|
Packstack
|
|
=========
|
|
|
|
SYNOPSIS
|
|
========
|
|
|
|
packstack [options]
|
|
|
|
DESCRIPTION
|
|
===========
|
|
|
|
Packstack is a utility that uses puppet modules to install OpenStack. It can be used to install each OpenStack service on separate servers, an 'allinone' server, or any combination of these. There are three ways that Packstack can be run.
|
|
|
|
- packstack
|
|
- packstack [options]
|
|
- packstack --gen-answer-file=<file> [options] / packstack --answer-file=<file>
|
|
|
|
The third option allows the user to generate a default answer file, edit the default options, and finally run Packstack a second time using this answer file. This is the easiest way to run Packstack and the one that will be documented here. Optionally, it is possible to set additional command-line options (such as a default password), and those options will be set in the answer file.
|
|
|
|
When <file> is created, it will contain the OPTIONS below, which can then be edited by the user.
|
|
|
|
OPTIONS
|
|
=======
|
|
|
|
Global Options
|
|
--------------
|
|
|
|
**CONFIG_SSH_KEY**
|
|
Path to a public key to install on servers. If a usable key has not been installed on the remote servers, the user is prompted for a password and this key is installed so the password will not be required again.
|
|
|
|
**CONFIG_DEFAULT_PASSWORD**
|
|
Default password to be used everywhere (overridden by passwords set for individual services or users).
|
|
|
|
**CONFIG_MARIADB_INSTALL**
|
|
Specify 'y' to install MariaDB. ['y', 'n']
|
|
|
|
**CONFIG_GLANCE_INSTALL**
|
|
Specify 'y' to install OpenStack Image Service (glance). ['y', 'n']
|
|
|
|
**CONFIG_CINDER_INSTALL**
|
|
Specify 'y' to install OpenStack Block Storage (cinder). ['y', 'n']
|
|
|
|
**CONFIG_MANILA_INSTALL**
|
|
Specify 'y' to install OpenStack Shared File System (manila). ['y', 'n']
|
|
|
|
**CONFIG_NOVA_INSTALL**
|
|
Specify 'y' to install OpenStack Compute (nova). ['y', 'n']
|
|
|
|
**CONFIG_NEUTRON_INSTALL**
|
|
Specify 'y' to install OpenStack Networking (neutron); otherwise, Compute Networking (nova) will be used. ['y', 'n']
|
|
|
|
**CONFIG_HORIZON_INSTALL**
|
|
Specify 'y' to install OpenStack Dashboard (horizon). ['y', 'n']
|
|
|
|
**CONFIG_SWIFT_INSTALL**
|
|
Specify 'y' to install OpenStack Object Storage (swift). ['y', 'n']
|
|
|
|
**CONFIG_CEILOMETER_INSTALL**
|
|
Specify 'y' to install OpenStack Metering (ceilometer). ['y', 'n']
|
|
|
|
**CONFIG_AODH_INSTALL**
|
|
Specify 'y' to install OpenStack Telemetry Alarming (Aodh). Note Aodh requires Ceilometer to be installed as well. ['y', 'n']
|
|
|
|
**CONFIG_GNOCCHI_INSTALL**
|
|
Specify 'y' to install OpenStack Metering as a Service (gnocchi). ['y', 'n']
|
|
|
|
**CONFIG_HEAT_INSTALL**
|
|
Specify 'y' to install OpenStack Orchestration (heat). ['y', 'n']
|
|
|
|
**CONFIG_SAHARA_INSTALL**
|
|
Specify 'y' to install OpenStack Data Processing (sahara). In case of sahara installation packstack also installs heat.['y', 'n']
|
|
|
|
**CONFIG_TROVE_INSTALL**
|
|
Specify 'y' to install OpenStack Database (trove) ['y', 'n']
|
|
|
|
**CONFIG_IRONIC_INSTALL**
|
|
Specify 'y' to install OpenStack Bare Metal Provisioning (ironic). ['y', 'n']
|
|
|
|
**CONFIG_CLIENT_INSTALL**
|
|
Specify 'y' to install the OpenStack Client packages (command-line tools). An admin "rc" file will also be installed. ['y', 'n']
|
|
|
|
**CONFIG_NTP_SERVERS**
|
|
Comma-separated list of NTP servers. Leave plain if Packstack should not install ntpd on instances.
|
|
|
|
**CONFIG_NAGIOS_INSTALL**
|
|
Specify 'y' to install Nagios to monitor OpenStack hosts. Nagios provides additional tools for monitoring the OpenStack environment. ['y', 'n']
|
|
|
|
**EXCLUDE_SERVERS**
|
|
Comma-separated list of servers to be excluded from the installation. This is helpful if you are running Packstack a second time with the same answer file and do not want Packstack to overwrite these server's configurations. Leave empty if you do not need to exclude any servers.
|
|
|
|
**CONFIG_DEBUG_MODE**
|
|
Specify 'y' if you want to run OpenStack services in debug mode; otherwise, specify 'n'. ['y', 'n']
|
|
|
|
**CONFIG_CONTROLLER_HOST**
|
|
Server on which to install OpenStack services specific to the controller role (for example, API servers or dashboard).
|
|
|
|
**CONFIG_COMPUTE_HOSTS**
|
|
List the servers on which to install the Compute service.
|
|
|
|
**CONFIG_NETWORK_HOSTS**
|
|
List of servers on which to install the network service such as Compute networking (nova network) or OpenStack Networking (neutron).
|
|
|
|
**CONFIG_VMWARE_BACKEND**
|
|
Specify 'y' if you want to use VMware vCenter as hypervisor and storage; otherwise, specify 'n'. ['y', 'n']
|
|
|
|
**CONFIG_UNSUPPORTED**
|
|
Specify 'y' if you want to use unsupported parameters. This should be used only if you know what you are doing. Issues caused by using unsupported options will not be fixed before the next major release. ['y', 'n']
|
|
|
|
**CONFIG_USE_SUBNETS**
|
|
Specify 'y' if you want to use subnet addresses (in CIDR format) instead of interface names in following options: CONFIG_NOVA_COMPUTE_PRIVIF, CONFIG_NOVA_NETWORK_PRIVIF, CONFIG_NOVA_NETWORK_PUBIF, CONFIG_NEUTRON_OVS_BRIDGE_IFACES, CONFIG_NEUTRON_LB_INTERFACE_MAPPINGS, CONFIG_NEUTRON_OVS_TUNNEL_IF. This is useful for cases when interface names are not same on all installation hosts.
|
|
|
|
SSL setup
|
|
---------
|
|
Packstack supports ability to be get CA certificate and use it to sign all certificates used in OpenStack deployment. Standard workflow for this would be creating Subordinate CA. If Root CA is given to Packstack it is not safe to use it for anything else. If no CA is provided and CONFIG_SSL_CACERT_SELFSIGN is set to 'y' Packstack will use Selfsigned CA.
|
|
|
|
**CONFIG_SSL_CERT_DIR**
|
|
Enter the path to use to store generated SSL certificates in.
|
|
|
|
**CONFIG_SSL_CACERT_FILE**
|
|
Specify filepath for CA cert file. If CONFIG_SSL_CACERT_SELFSIGN is set to 'n' it has to be preexisting file.
|
|
|
|
**CONFIG_SSL_CACERT_KEY_FILE**
|
|
Specify filepath for CA cert key file. If CONFIG_SSL_CACERT_SELFSIGN is set to 'n' it has to be preexisting file.
|
|
|
|
**CONFIG_SSL_CACERT_SELFSIGN**
|
|
Specify 'y' if you want Packstack to pregenerate the CA Certificate.
|
|
|
|
SSL selfsigned CACert options
|
|
-----------------------------
|
|
|
|
**CONFIG_SELFSIGN_CACERT_SUBJECT_C**
|
|
Enter the selfsigned CAcert subject country.
|
|
|
|
**CONFIG_SELFSIGN_CACERT_SUBJECT_ST**
|
|
Enter the selfsigned CAcert subject state.
|
|
|
|
**CONFIG_SELFSIGN_CACERT_SUBJECT_L**
|
|
Enter the selfsigned CAcert subject location.
|
|
|
|
**CONFIG_SELFSIGN_CACERT_SUBJECT_O**
|
|
Enter the selfsigned CAcert subject organization.
|
|
|
|
**CONFIG_SELFSIGN_CACERT_SUBJECT_OU**
|
|
Enter the selfsigned CAcert subject organizational unit.
|
|
|
|
**CONFIG_SELFSIGN_CACERT_SUBJECT_CN**
|
|
Enter the selfsigned CAcert subject common name.
|
|
|
|
vCenter Config Parameters
|
|
-------------------------
|
|
|
|
**CONFIG_VCENTER_HOST**
|
|
IP address of the VMware vCenter server.
|
|
|
|
**CONFIG_VCENTER_USER**
|
|
User name for VMware vCenter server authentication.
|
|
|
|
**CONFIG_VCENTER_PASSWORD**
|
|
Password for VMware vCenter server authentication.
|
|
|
|
**CONFIG_VCENTER_CLUSTER_NAMES**
|
|
Comma separated list of names of the VMware vCenter clusters.
|
|
Note: if multiple clusters are specified each one is mapped to one compute, otherwise all computes are mapped to same cluster.
|
|
|
|
Global unsupported options
|
|
--------------------------
|
|
|
|
**CONFIG_STORAGE_HOST**
|
|
(Unsupported!) Server on which to install OpenStack services specific to storage servers such as Image or Block Storage services.
|
|
|
|
**CONFIG_SAHARA_HOST**
|
|
(Unsupported!) Server on which to install OpenStack services specific to OpenStack Data Processing (sahara).
|
|
|
|
Server Prepare Configs
|
|
-----------------------
|
|
|
|
**CONFIG_USE_EPEL**
|
|
Specify 'y' to enable the EPEL repository (Extra Packages for Enterprise Linux). ['y', 'n']
|
|
|
|
**CONFIG_REPO**
|
|
Comma-separated list of URLs for any additional yum repositories, to use for installation.
|
|
|
|
**CONFIG_ENABLE_RDO_TESTING**
|
|
Specify 'y' to enable the RDO testing repository. ['y', 'n']
|
|
|
|
RHEL config
|
|
-----------
|
|
|
|
**CONFIG_RH_USER**
|
|
To subscribe each server with Red Hat Subscription Manager, include this with CONFIG_RH_PW.
|
|
|
|
**CONFIG_SATELLITE_URL**
|
|
To subscribe each server to receive updates from a Satellite server, provide the URL of the Satellite server. You must also provide a user name (CONFIG_SATELLITE_USERNAME) and password (CONFIG_SATELLITE_PASSWORD) or an access key (CONFIG_SATELLITE_AKEY) for authentication.
|
|
|
|
**CONFIG_RH_SAT6_SERVER**
|
|
Specify a Satellite 6 Server to register to. If not specified, Packstack will register the system to the Red Hat server. When this option is specified, you also need to set the Satellite 6 organization (CONFIG_RH_SAT6_ORG) and an activation key (CONFIG_RH_SAT6_KEY).
|
|
|
|
RH subscription manager config
|
|
------------------------------
|
|
|
|
**CONFIG_RH_PW**
|
|
To subscribe each server with Red Hat Subscription Manager, include this with CONFIG_RH_USER.
|
|
|
|
**CONFIG_RH_OPTIONAL**
|
|
Specify 'y' to enable RHEL optional repositories. ['y', 'n']
|
|
|
|
**CONFIG_RH_PROXY**
|
|
HTTP proxy to use with Red Hat Subscription Manager.
|
|
|
|
**CONFIG_RH_SAT6_ORG**
|
|
Specify a Satellite 6 Server organization to use when registering the system.
|
|
|
|
**CONFIG_RH_SAT6_KEY**
|
|
Specify a Satellite 6 Server activation key to use when registering the system.
|
|
|
|
RH subscription manager proxy config
|
|
------------------------------------
|
|
|
|
**CONFIG_RH_PROXY_PORT**
|
|
Port to use for Red Hat Subscription Manager's HTTP proxy.
|
|
|
|
**CONFIG_RH_PROXY_USER**
|
|
User name to use for Red Hat Subscription Manager's HTTP proxy.
|
|
|
|
**CONFIG_RH_PROXY_PW**
|
|
Password to use for Red Hat Subscription Manager's HTTP proxy.
|
|
|
|
RHN Satellite config
|
|
--------------------
|
|
|
|
**CONFIG_SATELLITE_USER**
|
|
User name to authenticate with the RHN Satellite server; if you intend to use an access key for Satellite authentication, leave this blank.
|
|
|
|
**CONFIG_SATELLITE_PW**
|
|
Password to authenticate with the RHN Satellite server; if you intend to use an access key for Satellite authentication, leave this blank.
|
|
|
|
**CONFIG_SATELLITE_AKEY**
|
|
Access key for the Satellite server; if you intend to use a user name and password for Satellite authentication, leave this blank.
|
|
|
|
**CONFIG_SATELLITE_CACERT**
|
|
Certificate path or URL of the certificate authority to verify that the connection with the Satellite server is secure. If you are not using Satellite in your deployment, leave this blank.
|
|
|
|
**CONFIG_SATELLITE_PROFILE**
|
|
Profile name that should be used as an identifier for the system in RHN Satellite (if required).
|
|
|
|
**CONFIG_SATELLITE_FLAGS**
|
|
Comma-separated list of flags passed to the rhnreg_ks command. Valid flags are: novirtinfo, norhnsd, nopackages ['novirtinfo', 'norhnsd', 'nopackages']
|
|
|
|
**CONFIG_SATELLITE_PROXY**
|
|
HTTP proxy to use when connecting to the RHN Satellite server (if required).
|
|
|
|
RHN Satellite proxy config
|
|
--------------------------
|
|
|
|
**CONFIG_SATELLITE_PROXY_USER**
|
|
User name to authenticate with the Satellite-server HTTP proxy.
|
|
|
|
**CONFIG_SATELLITE_PROXY_PW**
|
|
User password to authenticate with the Satellite-server HTTP proxy.
|
|
|
|
AMQP Config parameters
|
|
----------------------
|
|
|
|
**CONFIG_AMQP_BACKEND**
|
|
Service to be used as the AMQP broker. Allowed values are: rabbitmq ['rabbitmq']
|
|
|
|
**CONFIG_AMQP_HOST**
|
|
IP address of the server on which to install the AMQP service.
|
|
|
|
**CONFIG_AMQP_ENABLE_SSL**
|
|
Specify 'y' to enable SSL for the AMQP service. ['y', 'n']
|
|
|
|
**CONFIG_AMQP_ENABLE_AUTH**
|
|
Specify 'y' to enable authentication for the AMQP service. ['y', 'n']
|
|
|
|
AMQP Config SSL parameters
|
|
--------------------------
|
|
|
|
**CONFIG_AMQP_NSS_CERTDB_PW**
|
|
Password for the NSS certificate database of the AMQP service.
|
|
|
|
AMQP Config Athentication parameters
|
|
------------------------------------
|
|
|
|
**CONFIG_AMQP_AUTH_USER**
|
|
User for AMQP authentication.
|
|
|
|
**CONFIG_AMQP_AUTH_PASSWORD**
|
|
Password for AMQP authentication.
|
|
|
|
MariaDB Config parameters
|
|
-------------------------
|
|
|
|
**CONFIG_MARIADB_HOST**
|
|
IP address of the server on which to install MariaDB. If a MariaDB installation was not specified in CONFIG_MARIADB_INSTALL, specify the IP address of an existing database server (a MariaDB cluster can also be specified).
|
|
|
|
**CONFIG_MARIADB_USER**
|
|
User name for the MariaDB administrative user.
|
|
|
|
**CONFIG_MARIADB_PW**
|
|
Password for the MariaDB administrative user.
|
|
|
|
Keystone Config parameters
|
|
--------------------------
|
|
|
|
**CONFIG_KEYSTONE_DB_PW**
|
|
Password to use for the Identity service (keystone) to access the database.
|
|
|
|
**CONFIG_KEYSTONE_DB_PURGE_ENABLE**
|
|
Enter y if cron job for removing soft deleted DB rows should be created.
|
|
|
|
**CONFIG_KEYSTONE_REGION**
|
|
Default region name to use when creating tenants in the Identity service.
|
|
|
|
**CONFIG_KEYSTONE_ADMIN_TOKEN**
|
|
Token to use for the Identity service API.
|
|
|
|
**CONFIG_KEYSTONE_ADMIN_USERNAME**
|
|
User name for the Identity service 'admin' user. Defaults to 'admin'.
|
|
|
|
**CONFIG_KEYSTONE_ADMIN_PW**
|
|
Password to use for the Identity service 'admin' user.
|
|
|
|
**CONFIG_KEYSTONE_ADMIN_EMAIL**
|
|
Email address for the Identity service 'admin' user. Defaults to 'root@localhost'.
|
|
|
|
**CONFIG_KEYSTONE_DEMO_PW**
|
|
Password to use for the Identity service 'demo' user.
|
|
|
|
**CONFIG_KEYSTONE_API_VERSION**
|
|
Identity service API version string. ['v2.0', 'v3']
|
|
|
|
**CONFIG_KEYSTONE_TOKEN_FORMAT**
|
|
Identity service token format (UUID or PKI). The recommended format for new deployments is UUID. ['UUID', 'PKI']
|
|
|
|
**CONFIG_KEYSTONE_SERVICE_NAME**
|
|
Name of service to use to run the Identity service (keystone or httpd). ['keystone', 'httpd']
|
|
|
|
**CONFIG_KEYSTONE_IDENTITY_BACKEND**
|
|
Type of Identity service backend (sql or ldap). ['sql', 'ldap']
|
|
|
|
Keystone LDAP Identity Backend Config parameters
|
|
------------------------------------------------
|
|
|
|
**CONFIG_KEYSTONE_LDAP_URL**
|
|
URL for the Identity service LDAP backend.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_DN**
|
|
User DN for the Identity service LDAP backend. Used to bind to the LDAP server if the LDAP server does not allow anonymous authentication.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_PASSWORD**
|
|
User DN password for the Identity service LDAP backend.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_SUFFIX**
|
|
Base suffix for the Identity service LDAP backend.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_QUERY_SCOPE**
|
|
Query scope for the Identity service LDAP backend. Use 'one' for onelevel/singleLevel or 'sub' for subtree/wholeSubtree ('base' is not actually used by the Identity service and is therefore deprecated). ['base', 'one', 'sub']
|
|
|
|
**CONFIG_KEYSTONE_LDAP_PAGE_SIZE**
|
|
Query page size for the Identity service LDAP backend.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_SUBTREE**
|
|
User subtree for the Identity service LDAP backend.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_FILTER**
|
|
User query filter for the Identity service LDAP backend.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_OBJECTCLASS**
|
|
User object class for the Identity service LDAP backend.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_ID_ATTRIBUTE**
|
|
User ID attribute for the Identity service LDAP backend.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_NAME_ATTRIBUTE**
|
|
User name attribute for the Identity service LDAP backend.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_MAIL_ATTRIBUTE**
|
|
User email address attribute for the Identity service LDAP backend.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_ENABLED_ATTRIBUTE**
|
|
User-enabled attribute for the Identity service LDAP backend.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_ENABLED_MASK**
|
|
Bit mask integer applied to user-enabled attribute for the Identity service LDAP backend. Indicate the bit that the enabled value is stored in if the LDAP server represents "enabled" as a bit on an integer rather than a boolean. A value of "0" indicates the mask is not used (default). If this is not set to "0", the typical value is "2", typically used when "CONFIG_KEYSTONE_LDAP_USER_ENABLED_ATTRIBUTE = userAccountControl".
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_ENABLED_DEFAULT**
|
|
Value of enabled attribute which indicates user is enabled for the Identity service LDAP backend. This should match an appropriate integer value if the LDAP server uses non-boolean (bitmask) values to indicate whether a user is enabled or disabled. If this is not set as 'y', the typical value is "512". This is typically used when "CONFIG_KEYSTONE_LDAP_USER_ENABLED_ATTRIBUTE = userAccountControl".
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_ENABLED_INVERT**
|
|
Specify 'y' if users are disabled (not enabled) in the Identity service LDAP backend (inverts boolean-enalbed values). Some LDAP servers use a boolean lock attribute where "y" means an account is disabled. Setting this to 'y' allows these lock attributes to be used. This setting will have no effect if "CONFIG_KEYSTONE_LDAP_USER_ENABLED_MASK" is in use. ['n', 'y']
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_ATTRIBUTE_IGNORE**
|
|
Comma-separated list of attributes stripped from LDAP user entry upon update.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_DEFAULT_PROJECT_ID_ATTRIBUTE**
|
|
Identity service LDAP attribute mapped to default_project_id for users.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_ALLOW_CREATE**
|
|
Specify 'y' if you want to be able to create Identity service users through the Identity service interface; specify 'n' if you will create directly in the LDAP backend. ['n', 'y']
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_ALLOW_UPDATE**
|
|
Specify 'y' if you want to be able to update Identity service users through the Identity service interface; specify 'n' if you will update directly in the LDAP backend. ['n', 'y']
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_ALLOW_DELETE**
|
|
Specify 'y' if you want to be able to delete Identity service users through the Identity service interface; specify 'n' if you will delete directly in the LDAP backend. ['n', 'y']
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_PASS_ATTRIBUTE**
|
|
Identity service LDAP attribute mapped to password.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_ENABLED_EMULATION_DN**
|
|
DN of the group entry to hold enabled LDAP users when using enabled emulation.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USER_ADDITIONAL_ATTRIBUTE_MAPPING**
|
|
List of additional LDAP attributes for mapping additional attribute mappings for users. The attribute-mapping format is <ldap_attr>:<user_attr>, where ldap_attr is the attribute in the LDAP entry and user_attr is the Identity API attribute.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_GROUP_SUBTREE**
|
|
Group subtree for the Identity service LDAP backend.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_GROUP_FILTER**
|
|
Group query filter for the Identity service LDAP backend.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_GROUP_OBJECTCLASS**
|
|
Group object class for the Identity service LDAP backend.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_GROUP_ID_ATTRIBUTE**
|
|
Group ID attribute for the Identity service LDAP backend.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_GROUP_NAME_ATTRIBUTE**
|
|
Group name attribute for the Identity service LDAP backend.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_GROUP_MEMBER_ATTRIBUTE**
|
|
Group member attribute for the Identity service LDAP backend.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_GROUP_DESC_ATTRIBUTE**
|
|
Group description attribute for the Identity service LDAP backend.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_GROUP_ATTRIBUTE_IGNORE**
|
|
Comma-separated list of attributes stripped from LDAP group entry upon update.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_GROUP_ALLOW_CREATE**
|
|
Specify 'y' if you want to be able to create Identity service groups through the Identity service interface; specify 'n' if you will create directly in the LDAP backend. ['n', 'y']
|
|
|
|
**CONFIG_KEYSTONE_LDAP_GROUP_ALLOW_UPDATE**
|
|
Specify 'y' if you want to be able to update Identity service groups through the Identity service interface; specify 'n' if you will update directly in the LDAP backend. ['n', 'y']
|
|
|
|
**CONFIG_KEYSTONE_LDAP_GROUP_ALLOW_DELETE**
|
|
Specify 'y' if you want to be able to delete Identity service groups through the Identity service interface; specify 'n' if you will delete directly in the LDAP backend. ['n', 'y']
|
|
|
|
**CONFIG_KEYSTONE_LDAP_GROUP_ADDITIONAL_ATTRIBUTE_MAPPING**
|
|
List of additional LDAP attributes used for mapping additional attribute mappings for groups. The attribute=mapping format is <ldap_attr>:<group_attr>, where ldap_attr is the attribute in the LDAP entry and group_attr is the Identity API attribute.
|
|
|
|
**CONFIG_KEYSTONE_LDAP_USE_TLS**
|
|
Specify 'y' if the Identity service LDAP backend should use TLS. ['n', 'y']
|
|
|
|
**CONFIG_KEYSTONE_LDAP_TLS_CACERTDIR**
|
|
CA certificate directory for Identity service LDAP backend (if TLS is used).
|
|
|
|
**CONFIG_KEYSTONE_LDAP_TLS_CACERTFILE**
|
|
CA certificate file for Identity service LDAP backend (if TLS is used).
|
|
|
|
**CONFIG_KEYSTONE_LDAP_TLS_REQ_CERT**
|
|
Certificate-checking strictness level for Identity service LDAP backend; valid options are: never, allow, demand. ['never', 'allow', 'demand']
|
|
|
|
Glance Config parameters
|
|
------------------------
|
|
|
|
**CONFIG_GLANCE_DB_PW**
|
|
Password to use for the Image service (glance) to access the database.
|
|
|
|
**CONFIG_GLANCE_KS_PW**
|
|
Password to use for the Image service to authenticate with the Identity service.
|
|
|
|
**CONFIG_GLANCE_BACKEND**
|
|
Storage backend for the Image service (controls how the Image service stores disk images). Valid options are: file or swift (Object Storage). The Object Storage service must be enabled to use it as a working backend; otherwise, Packstack falls back to 'file'. ['file', 'swift']
|
|
|
|
Cinder Config parameters
|
|
------------------------
|
|
|
|
**CONFIG_CINDER_DB_PW**
|
|
Password to use for the Block Storage service (cinder) to access the database.
|
|
|
|
**CONFIG_CINDER_DB_PURGE_ENABLE**
|
|
Enter y if cron job for removing soft deleted DB rows should be created.
|
|
|
|
**CONFIG_CINDER_KS_PW**
|
|
Password to use for the Block Storage service to authenticate with the Identity service.
|
|
|
|
**CONFIG_CINDER_BACKEND**
|
|
Storage backend to use for the Block Storage service; valid options are: lvm, gluster, nfs, vmdk, netapp. ['lvm', 'gluster', 'nfs', 'vmdk', 'netapp']
|
|
|
|
Cinder volume create Config parameters
|
|
--------------------------------------
|
|
|
|
**CONFIG_CINDER_VOLUMES_CREATE**
|
|
Specify 'y' to create the Block Storage volumes group. That is, Packstack creates a raw disk image in /var/lib/cinder, and mounts it using a loopback device. This should only be used for testing on a proof-of-concept installation of the Block Storage service (a file-backed volume group is not suitable for production usage). ['y', 'n']
|
|
|
|
Cinder volume size Config parameters
|
|
------------------------------------
|
|
|
|
**CONFIG_CINDER_VOLUMES_SIZE**
|
|
Size of Block Storage volumes group. Actual volume size will be extended with 3% more space for VG metadata. Remember that the size of the volume group will restrict the amount of disk space that you can expose to Compute instances, and that the specified amount must be available on the device used for /var/lib/cinder.
|
|
|
|
Cinder gluster Config parameters
|
|
--------------------------------
|
|
|
|
**CONFIG_CINDER_GLUSTER_MOUNTS**
|
|
A single or comma-separated list of Red Hat Storage (gluster) volume shares to mount. Example: 'ip-address:/vol-name', 'domain:/vol-name'
|
|
|
|
Cinder NFS Config parameters
|
|
----------------------------
|
|
|
|
**CONFIG_CINDER_NFS_MOUNTS**
|
|
A single or comma-separated list of NFS exports to mount. Example: 'ip-address:/export-name'
|
|
|
|
Cinder NetApp main configuration
|
|
--------------------------------
|
|
|
|
**CONFIG_CINDER_NETAPP_LOGIN**
|
|
Administrative user account name used to access the NetApp storage system or proxy server.
|
|
|
|
**CONFIG_CINDER_NETAPP_PASSWORD**
|
|
Password for the NetApp administrative user account specified in the CONFIG_CINDER_NETAPP_LOGIN parameter.
|
|
|
|
**CONFIG_CINDER_NETAPP_HOSTNAME**
|
|
Hostname (or IP address) for the NetApp storage system or proxy server.
|
|
|
|
**CONFIG_CINDER_NETAPP_SERVER_PORT**
|
|
The TCP port to use for communication with the storage system or proxy. If not specified, Data ONTAP drivers will use 80 for HTTP and 443 for HTTPS; E-Series will use 8080 for HTTP and 8443 for HTTPS. Defaults to 80.
|
|
|
|
**CONFIG_CINDER_NETAPP_STORAGE_FAMILY**
|
|
Storage family type used on the NetApp storage system; valid options are ontap_7mode for using Data ONTAP operating in 7-Mode, ontap_cluster for using clustered Data ONTAP, or E-Series for NetApp E-Series. Defaults to ontap_cluster. ['ontap_7mode', 'ontap_cluster', 'eseries']
|
|
|
|
**CONFIG_CINDER_NETAPP_TRANSPORT_TYPE**
|
|
The transport protocol used when communicating with the NetApp storage system or proxy server. Valid values are http or https. Defaults to 'http'. ['http', 'https']
|
|
|
|
**CONFIG_CINDER_NETAPP_STORAGE_PROTOCOL**
|
|
Storage protocol to be used on the data path with the NetApp storage system; valid options are iscsi, fc, nfs. Defaults to nfs. ['iscsi', 'fc', 'nfs']
|
|
|
|
Cinder NetApp ONTAP-iSCSI configuration
|
|
---------------------------------------
|
|
|
|
**CONFIG_CINDER_NETAPP_SIZE_MULTIPLIER**
|
|
Quantity to be multiplied by the requested volume size to ensure enough space is available on the virtual storage server (Vserver) to fulfill the volume creation request. Defaults to 1.0.
|
|
|
|
Cinder NetApp NFS configuration
|
|
-------------------------------
|
|
|
|
**CONFIG_CINDER_NETAPP_EXPIRY_THRES_MINUTES**
|
|
Time period (in minutes) that is allowed to elapse after the image is last accessed, before it is deleted from the NFS image cache. When a cache-cleaning cycle begins, images in the cache that have not been accessed in the last M minutes, where M is the value of this parameter, are deleted from the cache to create free space on the NFS share. Defaults to 720.
|
|
|
|
**CONFIG_CINDER_NETAPP_THRES_AVL_SIZE_PERC_START**
|
|
If the percentage of available space for an NFS share has dropped below the value specified by this parameter, the NFS image cache is cleaned. Defaults to 20.
|
|
|
|
**CONFIG_CINDER_NETAPP_THRES_AVL_SIZE_PERC_STOP**
|
|
When the percentage of available space on an NFS share has reached the percentage specified by this parameter, the driver stops clearing files from the NFS image cache that have not been accessed in the last M minutes, where M is the value of the CONFIG_CINDER_NETAPP_EXPIRY_THRES_MINUTES parameter. Defaults to 60.
|
|
|
|
**CONFIG_CINDER_NETAPP_NFS_SHARES**
|
|
Single or comma-separated list of NetApp NFS shares for Block Storage to use. Format: ip-address:/export-name. Defaults to ''.
|
|
|
|
**CONFIG_CINDER_NETAPP_NFS_SHARES_CONFIG**
|
|
File with the list of available NFS shares. Defaults to '/etc/cinder/shares.conf'.
|
|
|
|
|
|
Cinder NetApp iSCSI & 7-mode configuration
|
|
------------------------------------------
|
|
|
|
**CONFIG_CINDER_NETAPP_VOLUME_LIST**
|
|
This parameter is only utilized when the storage protocol is configured to use iSCSI or FC. This parameter is used to restrict provisioning to the specified controller volumes. Specify the value of this parameter to be a comma separated list of NetApp controller volume names to be used for provisioning. Defaults to ''.
|
|
|
|
**CONFIG_CINDER_NETAPP_VFILER**
|
|
The vFiler unit on which provisioning of block storage volumes will be done. This parameter is only used by the driver when connecting to an instance with a storage family of Data ONTAP operating in 7-Mode Only use this parameter when utilizing the MultiStore feature on the NetApp storage system. Defaults to ''.
|
|
|
|
Cinder NetApp 7-mode FC configuration
|
|
-------------------------------------
|
|
|
|
**CONFIG_CINDER_NETAPP_PARTNER_BACKEND_NAME**
|
|
The name of the config.conf stanza for a Data ONTAP (7-mode) HA partner. This option is only used by the driver when connecting to an instance with a storage family of Data ONTAP operating in 7-Mode, and it is required if the storage protocol selected is FC. Defaults to ''.
|
|
|
|
Cinder NetApp Vserver configuration
|
|
-----------------------------------
|
|
|
|
**CONFIG_CINDER_NETAPP_VSERVER**
|
|
This option specifies the virtual storage server (Vserver) name on the storage cluster on which provisioning of block storage volumes should occur. Defaults to ''.
|
|
|
|
Cinder NetApp E-Series configuration
|
|
------------------------------------
|
|
|
|
**CONFIG_CINDER_NETAPP_CONTROLLER_IPS**
|
|
Restricts provisioning to the specified controllers. Value must be a comma-separated list of controller hostnames or IP addresses to be used for provisioning. This option is only utilized when the storage family is configured to use E-Series. Defaults to ''.
|
|
|
|
**CONFIG_CINDER_NETAPP_SA_PASSWORD**
|
|
Password for the NetApp E-Series storage array. Defaults to ''.
|
|
|
|
**CONFIG_CINDER_NETAPP_ESERIES_HOST_TYPE**
|
|
This option is used to define how the controllers in the E-Series storage array will work with the particular operating system on the hosts that are connected to it. Defaults to 'linux_dm_mp'
|
|
|
|
**CONFIG_CINDER_NETAPP_WEBSERVICE_PATH**
|
|
Path to the NetApp E-Series proxy application on a proxy server. The value is combined with the value of the CONFIG_CINDER_NETAPP_TRANSPORT_TYPE, CONFIG_CINDER_NETAPP_HOSTNAME, and CONFIG_CINDER_NETAPP_HOSTNAME options to create the URL used by the driver to connect to the proxy application. Defaults to '/devmgr/v2'.
|
|
|
|
**CONFIG_CINDER_NETAPP_STORAGE_POOLS**
|
|
Restricts provisioning to the specified storage pools. Only dynamic disk pools are currently supported. The value must be a comma-separated list of disk pool names to be used for provisioning. Defaults to ''.
|
|
|
|
Manila Config parameters
|
|
------------------------
|
|
|
|
**CONFIG_MANILA_DB_PW**
|
|
Password to use for the OpenStack File Share service (manila) to access the database.
|
|
|
|
**CONFIG_MANILA_KS_PW**
|
|
Password to use for the OpenStack File Share service (manila) to authenticate with the Identity service.
|
|
|
|
**CONFIG_MANILA_BACKEND**
|
|
Backend for the OpenStack File Share service (manila); valid options are: generic, netapp, glusternative, or glusternfs. ['generic', 'netapp', 'glusternative', 'glusternfs']
|
|
|
|
Manila NetApp configuration
|
|
---------------------------
|
|
|
|
**CONFIG_MANILA_NETAPP_DRV_HANDLES_SHARE_SERVERS**
|
|
Denotes whether the driver should handle the responsibility of managing share servers. This must be set to false if the driver is to operate without managing share servers. Defaults to 'false' ['true', 'false']
|
|
|
|
**CONFIG_MANILA_NETAPP_TRANSPORT_TYPE**
|
|
The transport protocol used when communicating with the storage system or proxy server. Valid values are 'http' and 'https'. Defaults to 'https'. ['https', 'http']
|
|
|
|
**CONFIG_MANILA_NETAPP_LOGIN**
|
|
Administrative user account name used to access the NetApp storage system. Defaults to ''.
|
|
|
|
**CONFIG_MANILA_NETAPP_PASSWORD**
|
|
Password for the NetApp administrative user account specified in the CONFIG_MANILA_NETAPP_LOGIN parameter. Defaults to ''.
|
|
|
|
**CONFIG_MANILA_NETAPP_SERVER_HOSTNAME**
|
|
Hostname (or IP address) for the NetApp storage system or proxy server. Defaults to ''.
|
|
|
|
**CONFIG_MANILA_NETAPP_STORAGE_FAMILY**
|
|
The storage family type used on the storage system; valid values are ontap_cluster for clustered Data ONTAP. Defaults to 'ontap_cluster'. ['ontap_cluster']
|
|
|
|
**CONFIG_MANILA_NETAPP_SERVER_PORT**
|
|
The TCP port to use for communication with the storage system or proxy server. If not specified, Data ONTAP drivers will use 80 for HTTP and 443 for HTTPS. Defaults to '443'.
|
|
|
|
**CONFIG_MANILA_NETAPP_AGGREGATE_NAME_SEARCH_PATTERN**
|
|
Pattern for searching available aggregates for NetApp provisioning. Defaults to '(.*)'.
|
|
|
|
Manila NetApp Multi-SVM configuration
|
|
-------------------------------------
|
|
|
|
**CONFIG_MANILA_NETAPP_ROOT_VOLUME_AGGREGATE**
|
|
Name of aggregate on which to create the NetApp root volume. This option only applies when the option CONFIG_MANILA_NETAPP_DRV_HANDLES_SHARE_SERVERS is set to True.
|
|
|
|
**CONFIG_MANILA_NETAPP_ROOT_VOLUME_NAME**
|
|
NetApp root volume name. Defaults to 'root'.
|
|
|
|
Manila NetApp Single-SVM configuration
|
|
--------------------------------------
|
|
|
|
**CONFIG_MANILA_NETAPP_VSERVER**
|
|
This option specifies the storage virtual machine (previously called a Vserver) name on the storage cluster on which provisioning of shared file systems should occur. This option only applies when the option driver_handles_share_servers is set to False. Defaults to ''.
|
|
|
|
Manila generic driver configuration
|
|
-----------------------------------
|
|
|
|
**CONFIG_MANILA_GENERIC_DRV_HANDLES_SHARE_SERVERS**
|
|
Denotes whether the driver should handle the responsibility of managing share servers. This must be set to false if the driver is to operate without managing share servers. Defaults to 'true'. ['true', 'false']
|
|
|
|
**CONFIG_MANILA_GENERIC_VOLUME_NAME_TEMPLATE**
|
|
Volume name template for Manila service. Defaults to 'manila-share-%s'.
|
|
|
|
**CONFIG_MANILA_GENERIC_SHARE_MOUNT_PATH**
|
|
Share mount path for Manila service. Defaults to '/shares'.
|
|
|
|
**CONFIG_MANILA_SERVICE_IMAGE_LOCATION**
|
|
Location of disk image for Manila service instance. Defaults to 'https://www.dropbox.com/s/vi5oeh10q1qkckh/ubuntu_1204_nfs_cifs.qcow2'.
|
|
|
|
**CONFIG_MANILA_SERVICE_INSTANCE_USER**
|
|
User in Manila service instance.
|
|
|
|
**CONFIG_MANILA_SERVICE_INSTANCE_PASSWORD**
|
|
Password to service instance user.
|
|
|
|
Manila Network configuration
|
|
----------------------------
|
|
|
|
**CONFIG_MANILA_NETWORK_TYPE**
|
|
Type of networking that the backend will use. A more detailed description of each option is available in the Manila docs. Defaults to 'neutron'. ['neutron', 'nova-network', 'standalone']
|
|
|
|
Manila Standalone network configuration
|
|
---------------------------------------
|
|
|
|
**CONFIG_MANILA_NETWORK_STANDALONE_GATEWAY**
|
|
Gateway IPv4 address that should be used. Required. Defaults to ''.
|
|
|
|
**CONFIG_MANILA_NETWORK_STANDALONE_NETMASK**
|
|
Network mask that will be used. Can be either decimal like '24' or binary like '255.255.255.0'. Required. Defaults to ''.
|
|
|
|
**CONFIG_MANILA_NETWORK_STANDALONE_SEG_ID**
|
|
Set it if network has segmentation (VLAN, VXLAN, etc). It will be assigned to share-network and share drivers will be able to use this for network interfaces within provisioned share servers. Optional. Example: 1001. Defaults to ''.
|
|
|
|
**CONFIG_MANILA_NETWORK_STANDALONE_IP_RANGE**
|
|
Can be IP address, range of IP addresses or list of addresses or ranges. Contains addresses from IP network that are allowed to be used. If empty, then will be assumed that all host addresses from network can be used. Optional. Examples: 10.0.0.10 or 10.0.0.10-10.0.0.20 or 10.0.0.10-10.0.0.20,10.0.0.30-10.0.0.40,10.0.0.50. Defaults to ''.
|
|
|
|
**CONFIG_MANILA_NETWORK_STANDALONE_IP_VERSION**
|
|
IP version of network. Optional. Defaults to '4'. ['4', '6']
|
|
|
|
Ironic Options
|
|
--------------
|
|
|
|
**CONFIG_IRONIC_DB_PW**
|
|
Password to use for OpenStack Bare Metal Provisioning (ironic) to access the database.
|
|
|
|
**CONFIG_IRONIC_KS_PW**
|
|
Password to use for OpenStack Bare Metal Provisioning to authenticate with the Identity service.
|
|
|
|
Nova Options
|
|
------------
|
|
|
|
**CONFIG_NOVA_DB_PW**
|
|
Password to use for the Compute service (nova) to access the database.
|
|
|
|
**CONFIG_NOVA_DB_PURGE_ENABLE**
|
|
Enter y if cron job for removing soft deleted DB rows should be created.
|
|
|
|
**CONFIG_NOVA_KS_PW**
|
|
Password to use for the Compute service to authenticate with the Identity service.
|
|
|
|
**CONFIG_NOVA_SCHED_CPU_ALLOC_RATIO**
|
|
Overcommitment ratio for virtual to physical CPUs. Specify 1.0 to disable CPU overcommitment.
|
|
|
|
**CONFIG_NOVA_SCHED_RAM_ALLOC_RATIO**
|
|
Overcommitment ratio for virtual to physical RAM. Specify 1.0 to disable RAM overcommitment.
|
|
|
|
**CONFIG_NOVA_COMPUTE_MIGRATE_PROTOCOL**
|
|
Protocol used for instance migration. Valid options are: tcp and ssh. Note that by default, the Compute user is created with the /sbin/nologin shell so that the SSH protocol will not work. To make the SSH protocol work, you must configure the Compute user on compute hosts manually. ['tcp', 'ssh']
|
|
|
|
**CONFIG_NOVA_COMPUTE_MANAGER**
|
|
Manager that runs the Compute service.
|
|
|
|
**CONFIG_NOVA_PCI_ALIAS**
|
|
Enter the PCI passthrough array of hash in JSON style for controller eg.
|
|
[{"vendor_id":"1234", "product_id":"5678", "name":"default"}, {...}]
|
|
|
|
**CONFIG_NOVA_PCI_PASSTHROUGH_WHITELIST**
|
|
Enter the PCI passthrough whitelist array of hash in JSON style for controller eg.
|
|
[{"vendor_id":"1234", "product_id":"5678", "name':"default"}, {...}]
|
|
|
|
**CONFIG_VNC_SSL_CERT**
|
|
PEM encoded certificate to be used for ssl on the https server, leave blank if one should be generated, this certificate should not require a passphrase. If CONFIG_HORIZON_SSL is set to 'n' this parameter is ignored.
|
|
|
|
**CONFIG_VNC_SSL_KEY**
|
|
SSL keyfile corresponding to the certificate if one was entered. If CONFIG_HORIZON_SSL is set to 'n' this parameter is ignored.
|
|
|
|
Nova Network Options
|
|
--------------------
|
|
|
|
**CONFIG_NOVA_COMPUTE_PRIVIF**
|
|
Private interface for flat DHCP on the Compute servers.
|
|
|
|
**CONFIG_NOVA_NETWORK_MANAGER**
|
|
Compute Network Manager. ['^nova\\.network\\.manager\\.\\w+Manager$']
|
|
|
|
**CONFIG_NOVA_NETWORK_PUBIF**
|
|
Public interface on the Compute network server.
|
|
|
|
**CONFIG_NOVA_NETWORK_PRIVIF**
|
|
Private interface for flat DHCP on the Compute network server.
|
|
|
|
**CONFIG_NOVA_NETWORK_FIXEDRANGE**
|
|
IP Range for flat DHCP. ['^[\\:\\.\\da-fA-f]+(\\/\\d+){0,1}$']
|
|
|
|
**CONFIG_NOVA_NETWORK_FLOATRANGE**
|
|
IP Range for floating IP addresses. ['^[\\:\\.\\da-fA-f]+(\\/\\d+){0,1}$']
|
|
|
|
**CONFIG_NOVA_NETWORK_AUTOASSIGNFLOATINGIP**
|
|
Specify 'y' to automatically assign a floating IP to new instances. ['y', 'n']
|
|
|
|
Nova Network VLAN Options
|
|
-------------------------
|
|
|
|
**CONFIG_NOVA_NETWORK_VLAN_START**
|
|
First VLAN for private networks (Compute networking).
|
|
|
|
**CONFIG_NOVA_NETWORK_NUMBER**
|
|
Number of networks to support (Compute networking).
|
|
|
|
**CONFIG_NOVA_NETWORK_SIZE**
|
|
Number of addresses in each private subnet (Compute networking).
|
|
|
|
Neutron config
|
|
--------------
|
|
|
|
**CONFIG_NEUTRON_KS_PW**
|
|
Password to use for OpenStack Networking (neutron) to authenticate with the Identity service.
|
|
|
|
**CONFIG_NEUTRON_DB_PW**
|
|
The password to use for OpenStack Networking to access the database.
|
|
|
|
**CONFIG_NEUTRON_L3_EXT_BRIDGE**
|
|
The name of the Open vSwitch bridge (or empty for linuxbridge) for the OpenStack Networking L3 agent to use for external traffic. Specify 'provider' if you intend to use a provider network to handle external traffic.
|
|
|
|
**CONFIG_NEUTRON_METADATA_PW**
|
|
Password for the OpenStack Networking metadata agent.
|
|
|
|
**CONFIG_LBAAS_INSTALL**
|
|
Specify 'y' to install OpenStack Networking's Load-Balancing-as-a-Service (LBaaS). ['y', 'n']
|
|
|
|
**CONFIG_NEUTRON_METERING_AGENT_INSTALL**
|
|
Specify 'y' to install OpenStack Networking's L3 Metering agent ['y', 'n']
|
|
|
|
**CONFIG_NEUTRON_FWAAS**
|
|
Specify 'y' to configure OpenStack Networking's Firewall-as-a-Service (FWaaS). ['y', 'n']
|
|
|
|
**CONFIG_NEUTRON_VPNAAS**
|
|
Specify 'y' to configure OpenStack Networking's VPN-as-a-Service (VPNaaS). ['y', 'n']
|
|
|
|
Neutron ML2 plugin config
|
|
-------------------------
|
|
|
|
**CONFIG_NEUTRON_ML2_TYPE_DRIVERS**
|
|
Comma-separated list of network-type driver entry points to be loaded from the neutron.ml2.type_drivers namespace. ['local', 'flat', 'vlan', 'gre', 'vxlan']
|
|
|
|
**CONFIG_NEUTRON_ML2_TENANT_NETWORK_TYPES**
|
|
Comma-separated, ordered list of network types to allocate as tenant networks. The 'local' value is only useful for single-box testing and provides no connectivity between hosts. ['local', 'vlan', 'gre', 'vxlan']
|
|
|
|
**CONFIG_NEUTRON_ML2_MECHANISM_DRIVERS**
|
|
Comma-separated ordered list of networking mechanism driver entry points to be loaded from the neutron.ml2.mechanism_drivers namespace. ['logger', 'test', 'linuxbridge', 'openvswitch', 'hyperv', 'ncs', 'arista', 'cisco_nexus', 'mlnx', 'l2population', 'sriovnicswitch']
|
|
|
|
**CONFIG_NEUTRON_ML2_FLAT_NETWORKS**
|
|
Comma-separated list of physical_network names with which flat networks can be created. Use * to allow flat networks with arbitrary physical_network names.
|
|
|
|
**CONFIG_NEUTRON_ML2_VLAN_RANGES**
|
|
Comma-separated list of <physical_network>:<vlan_min>:<vlan_max> or <physical_network> specifying physical_network names usable for VLAN provider and tenant networks, as well as ranges of VLAN tags on each available for allocation to tenant networks.
|
|
|
|
**CONFIG_NEUTRON_ML2_TUNNEL_ID_RANGES**
|
|
Comma-separated list of <tun_min>:<tun_max> tuples enumerating ranges of GRE tunnel IDs that are available for tenant-network allocation. A tuple must be an array with tun_max +1 - tun_min > 1000000.
|
|
|
|
**CONFIG_NEUTRON_ML2_VXLAN_GROUP**
|
|
Comma-separated list of addresses for VXLAN multicast group. If left empty, disables VXLAN from sending allocate broadcast traffic (disables multicast VXLAN mode). Should be a Multicast IP (v4 or v6) address.
|
|
|
|
**CONFIG_NEUTRON_ML2_SUPPORTED_PCI_VENDOR_DEVS**
|
|
Comma separated list of supported PCI vendor devices defined by vendor_id:product_id according to the PCI ID Repository.
|
|
|
|
**CONFIG_NEUTRON_ML2_VNI_RANGES**
|
|
Comma-separated list of <vni_min>:<vni_max> tuples enumerating ranges of VXLAN VNI IDs that are available for tenant network allocation. Minimum value is 0 and maximum value is 16777215.
|
|
|
|
**CONFIG_NEUTRON_ML2_SRIOV_AGENT_REQUIRED**
|
|
Specify 'y' if the sriov agent is required
|
|
|
|
**CONFIG_NEUTRON_ML2_SRIOV_INTERFACE_MAPPINGS**
|
|
Comma-separated list of interface mappings for the OpenStack Networking ML2 SRIOV agent. Each tuple in the list must be in the format <physical_network>:<net_interface>. Example: physnet1:eth1,physnet2:eth2,physnet3:eth3.
|
|
|
|
|
|
**CONFIG_NEUTRON_L2_AGENT**
|
|
Name of the L2 agent to be used with OpenStack Networking. ['linuxbridge', 'openvswitch']
|
|
|
|
Neutron LB agent config
|
|
-----------------------
|
|
|
|
**CONFIG_NEUTRON_LB_INTERFACE_MAPPINGS**
|
|
Comma-separated list of interface mappings for the OpenStack Networking linuxbridge plugin. Each tuple in the list must be in the format <physical_network>:<net_interface>. Example: physnet1:eth1,physnet2:eth2,physnet3:eth3.
|
|
|
|
Neutron OVS agent config
|
|
------------------------
|
|
|
|
**CONFIG_NEUTRON_OVS_BRIDGE_MAPPINGS**
|
|
Comma-separated list of bridge mappings for the OpenStack Networking Open vSwitch plugin. Each tuple in the list must be in the format <physical_network>:<ovs_bridge>. Example: physnet1:br-eth1,physnet2:br-eth2,physnet3:br-eth3
|
|
|
|
**CONFIG_NEUTRON_OVS_BRIDGE_IFACES**
|
|
Comma-separated list of colon-separated Open vSwitch <bridge>:<interface> pairs. The interface will be added to the associated bridge. If you desire the bridge to be persistent a value must be added to this directive, also CONFIG_NEUTRON_OVS_BRIDGE_MAPPINGS must be set in order to create the proper port. This can be achieved from the command line by issuing the following command: packstack --allinone --os-neutron-ovs-bridge-mappings=ext-net:br-ex --os-neutron-ovs-bridge-interfaces=br-ex:eth0
|
|
|
|
Neutron OVS agent config for tunnels
|
|
------------------------------------
|
|
|
|
**CONFIG_NEUTRON_OVS_TUNNEL_IF**
|
|
Interface for the Open vSwitch tunnel. Packstack overrides the IP address used for tunnels on this hypervisor to the IP found on the specified interface (for example, eth1).
|
|
|
|
**CONFIG_NEUTRON_OVS_TUNNEL_SUBNETS**
|
|
Comma-separated list of subnets (for example, 192.168.10.0/24,192.168.11.0/24) used for sending tunneling packets. This is used to configure IP filtering to accept tunneling packets from these subnets instead of specific IP addresses of peer nodes. This is useful when you add existing nodes to EXCLUDE_SERVERS because, in this case, packstack cannot modify the IP filtering of the existing nodes.
|
|
|
|
Neutron OVS agent config for VXLAN
|
|
----------------------------------
|
|
|
|
**CONFIG_NEUTRON_OVS_VXLAN_UDP_PORT**
|
|
VXLAN UDP port.
|
|
|
|
NOVACLIENT Config parameters
|
|
----------------------------
|
|
|
|
OpenStack Horizon Config parameters
|
|
-----------------------------------
|
|
|
|
**CONFIG_HORIZON_SSL**
|
|
Specify 'y' to set up Horizon communication over https. ['y', 'n']
|
|
|
|
**CONFIG_HORIZON_SECRET_KEY**
|
|
Secret key to use for Horizon Secret Encryption Key.
|
|
|
|
SSL Config parameters
|
|
---------------------
|
|
|
|
**CONFIG_HORIZON_SSL_CERT**
|
|
PEM-encoded certificate to be used for SSL connections on the https server. To generate a certificate, leave blank.
|
|
|
|
**CONFIG_HORIZON_SSL_KEY**
|
|
SSL keyfile corresponding to the certificate if one was specified. The certificate should not require a passphrase.
|
|
|
|
**CONFIG_HORIZON_SSL_CACHAIN**
|
|
PEM-encoded CA certificates from which the certificate chain of the server certificate can be assembled.
|
|
|
|
OpenStack Swift Config parameters
|
|
---------------------------------
|
|
|
|
**CONFIG_SWIFT_KS_PW**
|
|
Password to use for the Object Storage service to authenticate with the Identity service.
|
|
|
|
**CONFIG_SWIFT_STORAGES**
|
|
Comma-separated list of devices to use as storage device for Object Storage. Each entry must take the format /path/to/dev (for example, specifying /dev/vdb installs /dev/vdb as the Object Storage storage device; Packstack does not create the filesystem, you must do this first). If left empty, Packstack creates a loopback device for test setup.
|
|
|
|
**CONFIG_SWIFT_STORAGE_ZONES**
|
|
Number of Object Storage storage zones; this number MUST be no larger than the number of configured storage devices.
|
|
|
|
**CONFIG_SWIFT_STORAGE_REPLICAS**
|
|
Number of Object Storage storage replicas; this number MUST be no larger than the number of configured storage zones.
|
|
|
|
**CONFIG_SWIFT_STORAGE_FSTYPE**
|
|
File system type for storage nodes. ['xfs', 'ext4']
|
|
|
|
**CONFIG_SWIFT_HASH**
|
|
Custom seed number to use for swift_hash_path_suffix in /etc/swift/swift.conf. If you do not provide a value, a seed number is automatically generated.
|
|
|
|
**CONFIG_SWIFT_STORAGE_SIZE**
|
|
Size of the Object Storage loopback file storage device.
|
|
|
|
Heat Config parameters
|
|
----------------------
|
|
|
|
**CONFIG_HEAT_DB_PW**
|
|
Password used by Orchestration service user to authenticate against the database.
|
|
|
|
**CONFIG_HEAT_AUTH_ENC_KEY**
|
|
Encryption key to use for authentication in the Orchestration database (16, 24, or 32 chars).
|
|
|
|
**CONFIG_HEAT_KS_PW**
|
|
Password to use for the Orchestration service to authenticate with the Identity service.
|
|
|
|
**CONFIG_HEAT_CLOUDWATCH_INSTALL**
|
|
Specify 'y' to install the Orchestration CloudWatch API. ['y', 'n']
|
|
|
|
**CONFIG_HEAT_CFN_INSTALL**
|
|
Specify 'y' to install the Orchestration CloudFormation API. ['y', 'n']
|
|
|
|
**CONFIG_HEAT_DOMAIN**
|
|
Name of the Identity domain for Orchestration.
|
|
|
|
**CONFIG_HEAT_DOMAIN_ADMIN**
|
|
Name of the Identity domain administrative user for Orchestration.
|
|
|
|
**CONFIG_HEAT_DOMAIN_PASSWORD**
|
|
Password for the Identity domain administrative user for Orchestration.
|
|
|
|
Provisioning demo config
|
|
------------------------
|
|
|
|
**CONFIG_PROVISION_DEMO**
|
|
Specify 'y' to provision for demo usage and testing. ['y', 'n']
|
|
|
|
**CONFIG_PROVISION_TEMPEST**
|
|
Specify 'y' to configure the OpenStack Integration Test Suite (tempest) for testing. The test suite requires OpenStack Networking to be installed. ['y', 'n']
|
|
|
|
Provisioning demo config
|
|
------------------------
|
|
|
|
**CONFIG_PROVISION_DEMO_FLOATRANGE**
|
|
CIDR network address for the floating IP subnet.
|
|
|
|
**CONFIG_PROVISION_IMAGE_URL**
|
|
A URL or local file location for an image to download and provision in Glance (defaults to a URL for a recent "cirros" image).
|
|
|
|
**CONFIG_PROVISION_IMAGE_NAME**
|
|
The name to be assigned to the demo image in Glance (default "cirros").
|
|
|
|
**CONFIG_PROVISION_IMAGE_FORMAT**
|
|
Format for the demo image (default "qcow2").
|
|
|
|
**CONFIG_PROVISION_IMAGE_SSH_USER**
|
|
User to use when connecting to instances booted from the demo image.
|
|
|
|
Provisioning tempest config
|
|
---------------------------
|
|
|
|
**CONFIG_PROVISION_TEMPEST_USER**
|
|
Name of the Integration Test Suite provisioning user. If you do not provide a user name, Tempest is configured in a standalone mode.
|
|
|
|
**CONFIG_PROVISION_TEMPEST_USER_PW**
|
|
Password to use for the Integration Test Suite provisioning user.
|
|
|
|
**CONFIG_PROVISION_TEMPEST_FLOATRANGE**
|
|
CIDR network address for the floating IP subnet.
|
|
|
|
**CONFIG_PROVISION_TEMPEST_REPO_URI**
|
|
URI of the Integration Test Suite git repository.
|
|
|
|
**CONFIG_PROVISION_TEMPEST_REPO_REVISION**
|
|
Revision (branch) of the Integration Test Suite git repository.
|
|
|
|
**CONFIG_RUN_TEMPEST**
|
|
Specify 'y' to run Tempest smoke test as last step of installation.
|
|
|
|
**CONFIG_RUN_TEMPEST_TESTS**
|
|
Test suites to run, example: "smoke dashboard TelemetryAlarming". Optional, defaults to "smoke".
|
|
|
|
Provisioning all-in-one ovs bridge config
|
|
-----------------------------------------
|
|
|
|
**CONFIG_PROVISION_OVS_BRIDGE**
|
|
Specify 'y' to configure the Open vSwitch external bridge for an all-in-one deployment (the L3 external bridge acts as the gateway for virtual machines). ['y', 'n']
|
|
|
|
Ceilometer Config parameters
|
|
----------------------------
|
|
|
|
**CONFIG_CEILOMETER_SECRET**
|
|
Secret key for signing Telemetry service (ceilometer) messages.
|
|
|
|
**CONFIG_CEILOMETER_KS_PW**
|
|
Password to use for Telemetry to authenticate with the Identity service.
|
|
|
|
**CONFIG_CEILOMETER_COORDINATION_BACKEND**
|
|
Backend driver for Telemetry's group membership coordination. ['redis', 'none']
|
|
|
|
MONGODB Config parameters
|
|
-------------------------
|
|
|
|
**CONFIG_MONGODB_HOST**
|
|
IP address of the server on which to install MongoDB.
|
|
|
|
Redis Config parameters
|
|
-----------------------
|
|
|
|
**CONFIG_REDIS_MASTER_HOST**
|
|
IP address of the server on which to install the Redis master server.
|
|
|
|
**CONFIG_REDIS_PORT**
|
|
Port on which the Redis server(s) listens.
|
|
|
|
**CONFIG_REDIS_HA**
|
|
Specify 'y' to have Redis try to use HA. ['y', 'n']
|
|
|
|
**CONFIG_REDIS_SLAVE_HOSTS**
|
|
Hosts on which to install Redis slaves.
|
|
|
|
**CONFIG_REDIS_SENTINEL_HOSTS**
|
|
Hosts on which to install Redis sentinel servers.
|
|
|
|
**CONFIG_REDIS_SENTINEL_CONTACT_HOST**
|
|
Host to configure as the Redis coordination sentinel.
|
|
|
|
**CONFIG_REDIS_SENTINEL_PORT**
|
|
Port on which Redis sentinel servers listen.
|
|
|
|
**CONFIG_REDIS_SENTINEL_QUORUM**
|
|
Quorum value for Redis sentinel servers.
|
|
|
|
**CONFIG_REDIS_MASTER_NAME**
|
|
Name of the master server watched by the Redis sentinel. ['[a-z]+']
|
|
|
|
Aodh Config parameters
|
|
----------------------
|
|
|
|
**CONFIG_AODH_KS_PW**
|
|
Password to use for Telemetry Alarming to authenticate with the Identity service.
|
|
|
|
|
|
Gnocchi Config parameters
|
|
-------------------------
|
|
|
|
**CONFIG_GNOCCHI_DB_PW**
|
|
Password to use for Gnocchi to access the database.
|
|
|
|
**CONFIG_GNOCCHI_KS_PW**
|
|
Password to use for Gnocchi to authenticate with the Identity service.
|
|
|
|
|
|
Sahara Config parameters
|
|
------------------------
|
|
|
|
**CONFIG_SAHARA_DB_PW**
|
|
Password to use for OpenStack Data Processing (sahara) to access the database.
|
|
|
|
**CONFIG_SAHARA_KS_PW**
|
|
Password to use for OpenStack Data Processing to authenticate with the Identity service.
|
|
|
|
Trove config parameters
|
|
-----------------------
|
|
|
|
**CONFIG_TROVE_DB_PW**
|
|
Password to use for OpenStack Database-as-a-Service (trove) to access the database.
|
|
|
|
**CONFIG_TROVE_KS_PW**
|
|
Password to use for OpenStack Database-as-a-Service to authenticate with the Identity service.
|
|
|
|
**CONFIG_TROVE_NOVA_USER**
|
|
User name to use when OpenStack Database-as-a-Service connects to the Compute service.
|
|
|
|
**CONFIG_TROVE_NOVA_TENANT**
|
|
Tenant to use when OpenStack Database-as-a-Service connects to the Compute service.
|
|
|
|
**CONFIG_TROVE_NOVA_PW**
|
|
Password to use when OpenStack Database-as-a-Service connects to the Compute service.
|
|
|
|
Nagios Config parameters
|
|
------------------------
|
|
|
|
**CONFIG_NAGIOS_PW**
|
|
Password of the nagiosadmin user on the Nagios server.
|
|
|
|
Log files and Debug info
|
|
------------------------
|
|
|
|
Log files and generated puppet manifests can be found in the /var/tmp/packstack directory under a directory named by the date in which Packstack was run and a random string (for example, /var/tmp/packstack/20131022-204316-Bf3Ek2). Inside the directory are the openstack-setup.log file and a manifest directory, which contains puppet manifests and a log file for each one.
|
|
|
|
If debugging information is needed while running packstack, the -d switch will make it write more detailed information about the installation.
|
|
|
|
Examples:
|
|
|
|
If we need an all-in-one debug session:
|
|
|
|
packstack -d --allinone
|
|
|
|
If we need a answer file to tailor it and then debug:
|
|
|
|
packstack --gen-answer-file=ans.txt
|
|
packstack -d --answer-file=ans.txt
|
|
|
|
Glusterfs Native (FUSE) configuration info
|
|
------------------------------------------
|
|
|
|
**CONFIG_MANILA_GLUSTERFS_SERVERS**
|
|
List of GlusterFS servers that can be used to create shares. Each GlusterFS server should be of the form [remoteuser@]<volserver>, and they are assumed to belong to distinct Gluster clusters.
|
|
|
|
**CONFIG_MANILA_GLUSTERFS_NATIVE_PATH_TO_PRIVATE_KEY**
|
|
Path of Manila host's private SSH key file.
|
|
|
|
**CONFIG_MANILA_GLUSTERFS_VOLUME_PATTERN**
|
|
Regular expression template used to filter GlusterFS volumes for share creation. The regex template can optionally (ie. with support of the GlusterFS backend) contain the #{size} parameter which matches an integer (sequence of digits) in which case the value shall be intepreted as size of the volume in GB. Examples: "manila-share-volume-\d+$", "manila-share-volume-#{size}G-\d+$"; with matching volume names, respectively: "manila-share-volume-12", "manila-share-volume-3G-13". In latter example, the number that matches "#{size}", that is, 3, is an indication that the size of volume is 3G.
|
|
|
|
GlusterNFS configuration info
|
|
-----------------------------
|
|
|
|
**CONFIG_MANILA_GLUSTERFS_TARGET**
|
|
Specifies the GlusterFS volume to be mounted on the Manila host. For e.g: [remoteuser@]<volserver>:/<volid>
|
|
|
|
**CONFIG_MANILA_GLUSTERFS_MOUNT_POINT_BASE**
|
|
Base directory containing mount points for Gluster volumes.
|
|
|
|
**CONFIG_MANILA_GLUSTERFS_NFS_SERVER_TYPE**
|
|
Type of NFS server that mediate access to the Gluster volumes (Gluster or Ganesha).
|
|
|
|
**CONFIG_MANILA_GLUSTERFS_PATH_TO_PRIVATE_KEY**
|
|
Path of Manila host's private SSH key file.
|
|
|
|
**CONFIG_MANILA_GLUSTERFS_GANESHA_SERVER_IP**
|
|
Remote Ganesha server node's IP address.
|
|
|
|
SOURCE
|
|
======
|
|
* `packstack https://github.com/openstack/packstack`
|
|
* `puppet modules https://github.com/puppetlabs and https://github.com/packstack`
|